Poly(lactic) acid (PLA) is a compostable biopolymer and has been commercialised for the for the manufacture of short-shelf life products. As a result, increasing amounts of PLA are entering waste management systems and the environment; however, the degradation mechanism is unclear. While hydrolysis of the polymer occurs abiotically at elevated temperature in the presence of water, potential catalytic role for microbes in this process is yet to be established. In this study, we examined the degradation of PLA coupons from commercial packaging at a range of temperatures (25°, 37°, 45°, 50° and 55 °C) in soil and compost and compared with the degradation rates in sterile aqueous conditions by measuring loss of tensile strength and molecular weight (Mw). In addition, in order to assess the possible influence of abiotic soluble factors in compost and soil on degradation of PLA, degradation rates in microorganism-rich compost and soil were compared with sterile compost and soil extract at 50 °C. Temperature was determined to be the key parameter in PLA degradation and degradation rates in microorganism-rich compost and soil were faster than in sterile water at temperatures 45° and 50 °C determined by tensile strength and Mw loss. Furthermore, all tensile strength was lost faster after 30 and 36 days in microorganism-rich compost and soil, respectively, than in sterile compost and soil extract, 57 and 54 days, respectively at 50 °C. Significantly more Mw, 68% and 64%, was lost in compost and soil, respectively than in compost extract, Mw, 53%; and in soil extract, 57%. Therefore, degradation rates were faster in microorganism-rich compost and soil than in sterile compost and soil extract, which contained the abiotic soluble factors of compost and soil at 50 °C. These comparative studies support a direct role for microorganisms in PLA degradation at elevated temperatures in humid environments. No change in tensile strength or Mw was observed either 25° or 37 °C after 1 year suggesting that accumulation of PLA in the environment may cause future pollution issues. 相似文献
Novel molecular ecological techniques were used to study changes in microbial community structure and population during degradation of polylactide (PLA)/organically modified layered silicates (OMLS) nanocomposites. Cloned gene sequences belonging to members of the phyla Actinobacteria and Ascomycota comprized the most dominant groups of microorganisms during biodegradation of PLA/OMLS nanocomposites. Due to their numerical abundance, members of these microbial groups are likely to play an important role during biodegradation process. This paper presents new insights into the biodegradability of PLA/OMLS nanocomposites and highlights the importance of using novel molecular ecological techniques for in situ identification of new microorganisms involved in biodegradation of polymeric materials.
ZnO nanoparticles were fabricated by pulsed laser ablation (PLA) of a Zn metal in aqueous media, and aging effects on the morphology and photoluminescence properties of ZnO nanoparticles were investigated. The crystalline phase and particle morphology were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). It was found that small, well-defined ZnO nanoparticles were obtained by PLA of a Zn plate in aqueous media, and subsequent aging of the obtained ZnO nanoparticle suspension produced in cetyltrimethylammonium bromide (CTAB) solution led to the formation of spindle-like ZnO aggregates. However, in deionized water not the spindle-like ZnO aggregates but fluffy round aggregates were obtained. High-resolution transmission electron microscopic (HRTEM) observation indicated that the spindle-like ZnO aggregates were composed of many well-defined nanoparticles. Spindle-like aggregates exhibited strong exciton emission, while green emission could be suppressed via an aging process in the presence of CTAB. Moreover, thin films prepared by electrophoretic deposition (EPD) of ZnO nanoparticles after PLA in the presence of CTAB also possessed highly elongated aggregate structures that were possibly formed by surrounding the ZnO nanoparticles with double layers of CTAB molecules. 相似文献
Secondary ion mass spectrometry (SIMS) employing an SF5+ polyatomic primary ion source was used to depth profile through poly(methylmethacrylate) (PMMA), poly(lactic acid) (PLA) and polystyrene (PS) thin films at a series of temperatures from −125 °C to 150 °C. It was found that for PMMA, reduced temperature analysis produced depth profiles with increased secondary ion stability and reduced interfacial widths as compared to analysis at ambient temperature. Atomic force microscopy (AFM) images indicated that this improvement in interfacial width may be related to a decrease in sputter-induced topography. Depth profiling at higher temperatures was typically correlated with increased sputter rates. However, the improvements in interfacial widths and overall secondary ion stability were not as prevalent as was observed at low temperature. For PLA, improvements in signal intensities were observed at low temperatures, yet there was no significant change in secondary ion stability, interface widths or sputter rates. High temperatures yielded a significant decrease in secondary ion stability of the resulting profiles. PS films showed rapid degradation of characteristic secondary ion signals under all temperatures examined. 相似文献
This paper reports which are the possibilities of quantification by time of flight secondary ion mass spectrometry (ToF-SIMS) for some polymer blends. In order to assess the composition of the mixtures, we studied first different poly(l-lactide)/polymethylmethacrylate (PLA/PMMA) blends by X-ray photoelectron spectroscopy (XPS), this technique being quantitative. By XPS fitting of the C 1s level, we found a very good agreement of the measured concentrations with the initial compositions. Concerning ToF-SIMS data treatment, we used principal component analysis (PCA) on negative spectra allowing to discriminate one polymer from the other one. By partial least square regression (PLS), we found also a good agreement between the ToF-SIMS predicted and initial compositions. This shows that ToF-SIMS, in a similar way to XPS, can lead to quantitative results. In addition, the observed agreement between XPS (60-100 Å depth analyzed) and ToF-SIMS (10 Å depth analyzed) measurements show that there is no segregation of one of the two polymers onto the surface. 相似文献
Poly-(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) and poly-(l-lactic acid) (PLA) have attracted much interest in recent years since they are biodegradable, thus can replace synthetic non-degradable materials. In this study, improvements of PHBV, mechanical, phase inversions, and rheological properties were investigated after blending with PLA in varying ratio’s. Three different blends of commercially available PLAs with 92–98% l-lactide units and one grade of PHB with 5% valerate content were blended using a micro-compounder at 175 °C. The composition of PHBV in blends ranged from 50% to 80%. With the addition of PLA, increases in the flexural strength and elastic modulus were observed for several blends, while minor to no changes were detected in the elongation at break and tensile strength as compared to pure PHBV material. Like many conventional plastics, the complex viscosity decreased with increasing rotational frequency due to decreasing entanglements and molecular weight. The complex viscosity with respect to time was very stable for the blends, but no improvements in the PHBV viscosity were observed with the addition of PLA at 170 °C. Three phase inversion models were used to predict the continuity of the blends, and the results showed both dual- and PLA-continuity phase for the blends. In summary, the mechanical results showed improvements in the tensile and flexural properties, while the rheological observation showed minor improvements in the complex viscosity for numerous concentrations. 相似文献
Polylactide (PLA), a biodegradable polymer, produced from annually renewable natural resources, has a glass transition temperature in the range of 50–60 °C and is stiff and brittle at room temperature. In this communication we demonstrate that blending of PLA with atactic poly([R,S]-3-hydroxy butyrate) (a-PHB) leads to significant improvement of drawability and impact strength. The blends of PLA with a-PHB are biodegradable, similarly to plain PLA, and can be considered as a potential material for packaging, especially for food. 相似文献
Poly(lactic acid) (PLA) and poly(butylene adipate-co-terephthalate) (PBAT) were mixed at a ratio of 40:60, extruded to form granules and cast into film; then, the PLA, PBAT, and PBAT/PLA film samples were buried in real soil environments. The residual degraded samples were taken regularly from the soil and analyzed by SEM, DSC, TGA, IR spectroscopy and elemental analysis. The analyses showed that PBAT and PLA had different biodegradation mechanisms. Further, the melting temperature and the melting point change of the various components in the PBAT/PLA blend before and after the biodegradation essentially followed the process of the changes in the respective single polymers. After biodegradation, the carbon atom content in the molecular structure of the PBAT, PLA, and PBAT/PLA samples decreased, while the oxygen atom content increased, indicating that the samples indeed degraded. The biodegradation rates of PBAT and PLA in the PBAT/PLA blend were not the same as those for the single materials. 相似文献
The synthetic routes for preparation of several phospholipid analogues such as lithium alkyl-3-alkoxy allylvinyl-sn-glycerol 5 and 6 and lithium trans-2-amidomethyl phosphate 7 and lithium cholesterol ester phosphate 8 containing ether, amide, and phosphate ester moieties are described. 相似文献