Influence of Cu electroplating solutions on boron carbon nitride (BCN) film

Cu electroplating is required for the fabrication of Cu/low-k interconnections. The permeation of a plating solution into low-k films during Cu electroplating is a serious challenge for 45-nm nodes and more complex devices. We investigated the influence of Cu electroplating solutions on boron carbon nitride (BCN) as a low-k film. After dipping it into a Cu electroplating solution that contained additives, the BCN film's hydrophilic surface changed to a hydrophobic surface, and the incorporation of water into the BCN film was suppressed by surfactant adsorption. Sulfuric residue was detected on the BCN sample by thermal desorption spectroscopy after treatment in the Cu electroplating solution with additives; however, it was found through electrical measurements that this solution did not affect the leakage current or the dielectric constant of the BCN film. We successfully fabricated an electroplating Cu layer on a BCN film with good adhesion, and we believe that this BCN film is a sufficiently useful material for Cu/BCN integration in LSI.     

Density functional theory study of surface catalysis and adsorption on several elements in Group I-B and VIII

This review deals with the high-throughput field in surface catalysis and adsorption. Special focus is placed on advanced methods for knowledge discovery such as density functional theory (DFT) simulations. An inventory of successful cases on several elements in Group I-B and VIII is reported, including the relevant data and knowledge management, which are very important in chemical industry, fuel cell, and environment protection, for both scientific and economical reasons.      

碳原子1s~22s~22pns~3P态的能量和波函数

提出了构造碳原子1s~22s~22pns~3P态波函数的新方法,以Rayleigh-Ritz变分法为基础开发了一套计算碳原子1s~22s2~2pns~3P态波函数和能量的Mathemtica程序,具体计算了碳原子1s~22s~22pns~3P(n=3～6)态的波函数和非相对论能量及其相对论修正值(包括质量修正、单体达尔文修正、双体达尔文修正、自旋-自旋接触相互作用修正),计算结果与实验值非常接近.     

基于石墨相氮化碳量子点直接荧光猝灭法检测碘离子的研究

石墨相氮化碳(g-C₃N₄)荧光纳米材料具有原料便宜、制备容易、荧光量子产率高、光学稳定性好、毒性低等优点,并且避免有机荧光染料复杂的合成步骤或者金属半导体量子点对环境潜在的危害,这些优点使得g-C₃N₄纳米材料成为新兴的荧光探针用于检测金属离子。最近,已有文献报道重金属汞离子能够高灵敏高选择性地猝灭g-C₃N₄量子点的荧光,加入碘离子能够提取被键合的汞离子形成碘化汞(HgI₂)进而恢复g-C₃N₄量子点的荧光,从而建立一种高灵敏检测碘离子的荧光传感器。然而,该方法依然需要重金属汞离子的参与,限制了该方法的推广应用。通过硝酸氧化块体g-C₃N₄并结合水热法处理制备了一种水溶性好、荧光强度高的g-C₃N₄量子点。该量子点的荧光发射波长位于368 nm,且其荧光发射波长不随激发波长的改变而改变,表明该量子点的尺寸比较均一。笔者发现碘离子在220 nm处有一个较强的吸收峰,与该量子点的激发光谱(中心波长245 nm)具有较大的重叠,从而产生内滤效应引起该量子点的荧光发生猝灭。利用这一性质,构建了一种选择性检测碘离子的新型荧光传感器。在最优检测条件下,g-C₃N₄量子点的荧光猝灭强度(ΔF)与碘离子浓度(X,μmol·L-1)在10～400 μmol·L-1之间具有良好的线性关系,线性方程为ΔF=0.325 79X+6.039 05(R2=0.999 5),检出限为5.0 μmol·L-1。通过“混合即检测”并且不需要借助与重金属离子的配位作用就能够检测碘离子,因此该方法具有快速、环保以及操作简便等优点。     

Relation between interfacial shear strength and compressive strength of carbon fiber/epoxy resin composite strands

The mechanism with which the fiber-matrix interfacial strength exerts its influence on the compressive strength of fiber reinforced composites has been studied by measuring the axial compressive strength of carbon fiber/epoxy resin unidirectional composite strands having different levels of interfacial shear strength. The composite strands are used for experiments in order to investigate the compressive strength which is not affected by the delamination taking place at a weak interlayer of the laminated composites. The interfacial strength is varied by applying various degrees of liquid-phase surface treatment to the fibers. The efficiency of the compressive strength of the fibers utilized in the strength of the composite strands is estimated by measuring the compressive strength of the single carbon filaments with a micro-compression test. The compressive strength of the composite strands does not increase monotonically with increasing interfacial shear strength but showes lower values at higher interfacial shear strengths. With increasing interfacial shear strength, the suppression of the interfacial failure in the misaligned fiber region increases the compressive strength, while at higher interfacial shear strengths, the enhancement of the crack sensitivity decreases the compressive strength.     

Carbon-nanodot-coverage-dependent photocatalytic performance of carbon nanodot/TiO_2 nanocomposites under visible light

Carbon nanodots(CDs) with visible absorption band and TiO_2 are integrated to enhance the photosensitivity of TiO_2.The CD/TiO_2 nanocomposites show obvious CD-coverage-dependent photocatalytic performance. The CD/TiO_2 nanocomposites with moderate CD coverge exhibit the highest photocatalytic activity after being irradiated with visible light, which is more excellent than that of TiO_2. Too little CD coverage could result in poor visible light absorption, which limits the photocatalytic performance of CD/TiO_2 nanocomposites. While, too much CD coverage weakens the photocatalytic activity of CD/TiO_2 nanocomposites by restraining the extraction of conduction band electrons within TiO_2 to generate active oxygen radicals and the electron transfer(ET) process from CDs to TiO_2. These results indicate that rational regulation of CD coverage and the realization of efficient ET process are important means to optimize the photocatalytic performance of CD/TiO_2 nanocomposites.     

Изотопные мишени для ядерных исследований

A non-contact measuring method on electrostatic potential by using α-ray ionization is proposed. In this method potential of a charged material is estimated from ionic current flowing through an ion collector attached with a small ²⁴¹Am source. As hade electrode surrounding the collector has a function of adjusting sensitivity and potential up to 50 kV was measured with precision of 1 kV.     

Eine Apparatur zur Messung natürlicher 4C-Aktivitäten

Aufbau, Arbeitsweise und Eigenschaften einer Apparatur, mit der naturliche ^l4C-Aktiviäten in Grund- und Oberflächenwässern gemessen werden können, werden beschrieben.

Die Messung erfordert 3 Arbeitsschritte: Probenahme, Synthese von Benzol, welches dann den Probenkohlenstoff enthält, und Messung der ¹⁴C-Aktivität in einem Flüssigkeitsszintillationszähler.

Die Apparatur kann zur Datierung von Wasserproben im Altersbereich zwischen 200 und 37000 a verwendet werden.     

Seletivitätsbestimmung von Katalysatoren zur Toluolentalkylierung durch Einsatz von Toluol-14C-7

Die bei der katalytischen Toulolentalkylierung mögliche Konkurrenzreaktion der Spaltung des aromatischen Kernes führt zu unerwünschten Verlusten an Aromaten und kann infolge ihrer starken exothermen Wärmetönung bei der technischen Realisierung des Verfahrens Schwierigkeiten bei der thermischen Beherrschung des Reaktors bewirken. Bereits in der Entwicklungsphase des Katalysators ist man somit auf ein Verfahren angewiesen, das es erlaubt, diese Ringspaltung sicher nachzuweisen und quantitativ zu bestimmen.

In der vorliegenden Arbeit wird eine Tracermethode unter Einsatz von Toluol-¹⁴C-7 beschrieben, die diese Forderung weitgehendst erfüllt.     

Methane-Derived Carbonates in a Native Sulfur Deposit: Stable Isotope and Trace Element Discriminations Related to the Transformation of Aragonite to Calcite

Abstract

Stable isotope (¹³C, ¹⁸O, ³⁴S) and trace element (Sr²⁺, Mg²⁺, Mn²⁺, Ba²⁺, Na⁺) investigations of elemental sulfur, primary calcites and mixtures of aragonite with secondary, post-aragonitic calcite from sulfur-bearing limestones have provided new insights into the geochemistry of the mineral forming environment of the native sulfur deposit at Machów (SE-Poland). The carbon isotopic composition of carbonates (δ¹³C = ?41 to ?47‰ vs. PDB) associated with native sulfur (δ³⁴S = + 10 to + 15‰ vs. V-CDT) relates their formation to the microbiological anaerobic oxidation of methane and the reduction of sulfate derived from Miocene gypsum. From a comparison with experimentally derived fractionation factors the element ratios of the aqueous fluids responsible for carbonate formation are estimated. In agreement with field and laboratory observations, ratios near seawater composition are obtained for primary aragonite, whereas the fluids were relatively enriched in dissolved calcium during the formation of primary and secondary calcites. Based on the oxygen isotope composition of the carbonates (δ¹⁸O = ?3.9 to ?5.9‰ vs. PDB) and a secondary SrSO₄ (δ¹⁸O = + 20‰ vs. SMOW; δ³⁴S = + 59‰ vs. V-CDT), maximum formation temperatures of 35°C (carbonates) and 47°C (celestite) are obtained, in agreement with estimates for West Ukraine sulfur ores. The sulfur isotopic composition of elemental sulfur associated with carbonates points to intense microbial reduction of sulfate derived from Miocene gypsum (δ³⁴S ≈ + 23‰) prior to the re-oxidation of dissolved reduced sulfur species.