Singlewall carbon nanotubes covered with polystyrene nanoparticles by in‐situ miniemulsion polymerization

This work is to make carbon nanotubes dispersible in both water and organic solvents without oxidation and cutting nanotube threads. Polystyrene‐singlewall carbon nanotube (PS‐SWNT) composites were prepared with three different methods: miniemulsion polymerization, conventional emulsion polymerization, and mixing SWNT with PS latex. The two factors, crosslinking and surface coverage of PS are important factors for the mechanical and electrical properties, including dispersion states of SWNT in various solvents. The PS‐SWNT composite prepared via a conventional emulsion polymerization showed SWNT bundles entirely covered with PS, whereas the PS‐SWNT composite prepared via a miniemulsion polymerization showed SWNT partially covered with crosslinked PS nanoparticles. The method of mixing SWNTs with PS latex did not show the well dispersed state of carbon nanotubes because PS was not crosslinked and was dissolved in a solvent, and nanotubes separated from PS precipitated. So the PS nanoparticle‐SWNT composite had lower electrical resistance, and higher mechanical strength than the other composites made by the latter two methods. As the amount of SWNT increases, the bare surface area of SWNT increases and the electrical conductivity increases in the composite made by the miniemulsion polymerization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 573–584, 2006     

Chiral discrimination of a helically organized crown ether array parallel to the helix axis of polyisocyanate

The asymmetric polymerization of 4′‐isocyanatobenzo‐18‐crown‐6 with the lithium amide of (S)‐(2‐methoxymethyl)pyrrolidine successfully proceeded to afford end‐functionalized poly(4′‐isocyanatobenzo‐18‐crown‐6) with (S)‐(2‐methoxymethyl)pyrrolidine (polymer 2 ). In the circular dichroism (CD) spectrum of 2 , a clear positive Cotton effect was observed in the range of 240–350 nm corresponding to the absorption of the polymer backbone, indicating that 2 partially formed a one‐handed helical structure, which was preserved by the chirality of (S)‐(2‐methoxymethyl)pyrrolidine bonding to the terminal end in 2 . In the titration experiments for the CD intensity of 2 in the presence of D ‐ and L ‐Phe·HClO₄ (where Phe is phenylalanine), a small but remarkable difference was observed in the amount of the chiral guest needed for saturation of the CD intensity and in the saturated CD intensity, indicating that the extremely stable, one‐handed helical part should exist in the main chain of 2 , which was not inverted even when the unfavorable chiral guest for the predominant helical sense, L ‐Phe·HClO₄, was added. In addition, helical polymer 2 exhibited a chiral discrimination ability toward racemic guests; that is, the guests were extracted from the aqueous phase into the organic phase with enantiomeric excess. The driving force of the chiral discrimination ability of 2 should certainly be attributed to the one‐handed helical structure in 2 . © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 325–334, 2006     

Synthesis,characterization, and electrical properties of polypyrrole/multiwalled carbon nanotube composites

Size‐controllable polypyrrole (PPy)/multiwalled carbon nanotube (MWCNT) composites have been synthesized by in situ chemical oxidation polymerization directed by various concentrations of cationic surfactant cetyltrimethylammonium bromide (CTAB). Raman spectra, FTIR, SEM, and TEM were used to characterize their structure and morphology. These results showed that the composites are core (MWCNT)–shell (PPy) tubular structures with the thickness of the PPy layer in the range of 20–40 nm, depending on the concentration of CTAB. Raman and FTIR spectra of the composites are almost identical to those of PPy alone. The electrical conductivities of these composites are 1–2 orders of magnitude higher than those of PPy without MWCNTs. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6449–6457, 2006     

Continuous reaction system to investigate the dispersion polymerization of vinyl monomers in supercritical carbon dioxide

A laboratory‐scale continuous reaction system using a stirred tank reactor was assembled in our laboratory to study the dispersion polymerization of vinyl monomers in supercritical carbon dioxide (scCO₂). The apparatus was equipped with a suitable downstream separation section to collect solid particles entrained in the effluent stream from the reactor, whose monomer concentration could be measured online with a gas chromatograph. The dispersion polymerization of methyl methacrylate in scCO₂ was selected as a model process to be investigated in the apparatus. The experiments were performed at 65 °C and 25 MPa with 2,2′‐azobisisobutyronitrile as the initiator and a reactive polysiloxane macromonomer as a surfactant to investigate the effect of the mean residence time of the reaction mixture on the monomer conversion, polymerization rate, polymer molecular weight, and particle size distribution. The results were compared with those obtained in batch polymerizations carried out under similar operative conditions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4122–4135, 2006     

Measurement and prediction of solubilities and diffusion coefficients of carbon dioxide in starch–water mixtures at elevated pressures

The solubility and diffusion coefficient of carbon dioxide in intermediate‐moisture starch–water mixtures were determined both experimentally and theoretically at elevated pressures up to 16 MPa at 50 °C. A high‐pressure decay sorption system was assembled to measure the equilibrium CO₂ mass uptake by the starch–water system. The experimentally measured solubilities accounted for the estimated swollen volume by Sanchez–Lacombe equation of state (S‐L EOS) were found to increase almost linearly with pressure, yielding 4.0 g CO₂/g starch–water system at 16 MPa. Moreover, CO₂ solubilities above 5 MPa displayed a solubility increase, which was not contributed by the water fraction in the starch–water mixture. The solubilities, however, showed no dependence on the degree of gelatinization (DG) of starch. The diffusion coefficient of CO₂ was found to increase with concentration of dissolved CO₂, which is pressure‐dependent, and decrease with increasing DG in the range of 50–100%. A free‐volume‐based diffusion model proposed by Areerat was employed to predict the CO₂ diffusivity in terms of pressure, temperature, and the concentration of dissolved CO₂. S‐L EOS was once more used to determine the specific free volume of the mixture system. The predicted diffusion coefficients showed to correlate well with the measured values for all starch–water mixtures. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 607–621, 2006     

Characterization and electrical properties of polypyrrole/multiwalled carbon nanotube composites synthesized by in situ chemical oxidative polymerization

This study describes the preparation of polypyrrole (PPy)/multiwalled carbon nanotube (MWNT) composites by in situ chemical oxidative polymerization. Various ratios of MWNTs, which served as hard templates, were first dispersed in aqueous solutions with the surfactant cetyltrimethylammonium bromide to form micelle/MWNT templates and overcome the difficulty of MWNTs dispersing into insoluble solutions of pyrrole monomer, and PPy was then synthesized via in situ chemical oxidative polymerization on the surface of the templates. Raman spectroscopy, Fourier transform infrared (FTIR), field‐emission scanning electron microscopy (FESEM), and high‐resolution transmission electron microscopy (HRTEM) were used to characterize the structure and morphology of the fabricated composites. Structural analysis using FESEM and HRTEM showed that the PPy/MWNT composites were core (MWNT)–shell (PPy) tubular structures. Raman and FTIR spectra of the composites were almost identical to those of PPy, supporting the idea that MWNTs served as the core in the formation of a coaxial nanostructure for the composites. The conductivities of these PPy/MWNT composites were about 150% higher than those of PPy without MWNTs. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1413–1418, 2006     

气密性碳涂覆光纤筛选强度与电阻关系研究

通过实验分析确立了把光纤电阻作为衡量气密性碳涂覆光纤通过２％应变筛选的过渡标准。要拉制２％应变筛选的碳涂覆光纤，其电阻值应小于３０ｋΩ／ｃｍ。     

Gas transport through homogeneous and asymmetric polyethersulfone membranes

Both homogeneous and asymmetric polyethersulfone (PES) membranes were prepared by solvent casting. The sorption and permeation behavior of CO₂, O₂, and N₂ using these two kinds of cast PES membranes and commercially available homogeneous PES film was investigated to extract the pressure dependence of gas permeability and the permselectivity for CO₂ relative to N₂, and to confirm the validity of the working assumption that a skin layer in an asymmetric membrane can be essentially replaced by a thick homogeneous dense membrane. The pressure dependence of the mean permeability coefficient to CO₂ in homogeneous membranes obeys the dual-mode mobility model. The ideal separation factor for CO₂ relative to N₂ at an upstream pressure of 0.5 MPa attains ca. 40, while the permeability to CO₂ is about 2.7 Barrer at the same upstream pressure. The same separation factor in asymmetric membranes amounts to 35. The diffusion behavior for the skin layer in an asymmetric membrane with a thin skin layer can be simulated approximately by that in a homogeneous dense membrane. © 1993 John Wiley & Sons, Inc.     

碳原子簇的结构与质谱的关联（Ⅱ）

根据出现在质谱中的各种大小的碳原子簇的相对丰度,分析了由激光产生的碳原子簇离子的统计分布,研究了这些统计分布与碳原子簇结构的关联。研究结果表明：相同构型的原子簇的相对丰度可以由同一条对数正态分布曲线来描述,由此能够获得碳原子簇构型的变化情况。质谱中分布曲线的数目对应于具有不同构型或不同结构稳定性的原子簇的数目。如果某些簇离子的谱峰明显地高出分布曲线,它们的结构应特别稳定,其成簇原子数就是所谓的“奇幻数”（ｍａｇｉｃｎｕｍｂｅｒ）,例如在石墨质谱中的Ｃ＿（６０）就属于这种情况。原子簇的统计分布还与它们的生成过程有关,由此可能揭示出原子簇的产生机理。