LES of turbulent heat transfer: proper convection numerical schemes for temperature transport

Large eddy simulations of two basic configurations (decay of isotropic turbulence, and the academic plane channel flow) with heat transfer have been performed comparing several convection numerical schemes, in order to discuss their ability to evaluate temperature fluctuations properly. Results are compared with the available incompressible heat transfer direct numerical simulation data. It is shown that the use of regularizing schemes (such as high order upwind type schemes) for the temperature transport equation in combination with centered schemes for momentum transport equation gives better results than the use of centred schemes for both equations. Copyright © 2004 John Wiley & Sons, Ltd.     

Numerical simulation and experimental validation of heat transfer within rotating flows for three‐dimensional non‐axisymmetric,turbulent conditions

A control volume type numerical methodology for the analysis of steady three‐dimensional rotating flows with heat transfer, in both laminar and turbulent conditions, is implemented and experimentally tested. Non‐axisymmetric momentum and heat transfer phenomena are allowed for. Turbulent transport is alternatively represented through three existing versions of the k–ε model that were adjusted to take into account the turbulence anisotropy promoted by rotation, streamline curvature and thermal buoyancy. Their relative performance is evaluated by comparison of calculated local and global heat balances with those obtained through measurements in a laboratory device. A modified version of the Lam and Bremhorst, low Reynolds number model is seen to give the best results. A preliminary analysis focused on the flow structure and the transfer of heat is reported. Copyright © 2002 John Wiley & Sons, Ltd.     

Thermal conductivity of poly(vinyl chloride)/polycaprolactone blends

Thermal diffusivity, heat capacity, and density of polyvinyl chloride/polycaprolactone (PVC/PCL) blends were measured by the laser flash method, DSC, and pycnometry, respectively. The thermal conductivity of the PVC/PCL blends was determined from the results. The miscibility of the blend and crystallinity of PCL were determined by DSC. The effect of blend structure on thermal conductivity is discussed. The phase compositions of the PVC/PCL blends are of three types depending on PCL content: i.e., up to 33%, from 33 to 70%, and above 70% PCL by weight. Thermal conductivity, thermal diffusivity, and heat capacity of the PVC/PCL blends are strongly affected by the phase composition of the blend, which changes in a complicated way with PCL content. © 1994 John Wiley & Sons, Inc.     

Towards understanding the increase in strength of thermotropic polyesters with heat treatment

Thermotropic copolyester fibers of oxynaphthoate and oxybenzoate have been subjected to conditions that promote solid-state polymerization as well as annealing. The annealing process causes the crystals to perfect with a simultaneous increase in heat of fusion and melting temperature. Solid-state polymerization, a reaction rate-controlled process, causes the polymer viscosity average molecular weight to increase by chain extension from about 14,000 g/mole to more than 87,000 g/mole with a simultaneous impressive increase in tenacity from about 10 g/d (1.2 GPa) to almost 30 g/d (3.7 GPa). To understand the changes in mechanical properties, we have modeled the fiber structure as short rod-like molecules poorly bonded to a continuous matrix of parallel molecules. Lengthening of the reinforcing molecules facilitates better transfer of load from matrix to molecules, resulting in higher tenacity fibers. © 1994 John Wiley & Sons, Inc.     

低速二维流动的粒子仿真研究

本文运用信息保存法对低速二维的流动现象进行模拟，考察了低速条件下的有限平板绕流以及微槽道气体流动问题。研究表明：在对低速流动的模拟过程中，运用IP法在能够获得较好的结果的同时，具有比DSMC方法更高的计算效率。     

Effect of the incomplete accommodation of the heterogeneous recombination energy on heat fluxes to a quartz surface

Taking both the heterogeneous catalytic processes, including the surface formation of particles with excited internal degrees of freedom, and the processes of multicomponent diffusion and heat transfer in the MESOX apparatus fully into account makes it possible to obtain a recombination coefficient and an accommodation coefficient of the oxygen-atoms-on-quartz recombination energy which are in good agreement with the experimental data. The heterogeneous catalysis model constructed can be used effectively for predicting the heat fluxes to the surface of reentry vehicles on their entry into the Earth’s atmosphere.     

Boiling heat transfer characteristics of nanofluids in a flat heat pipe evaporator with micro-grooved heating surface

An experimental study was performed to understand the nucleate boiling heat transfer of water–CuO nanoparticles suspension (nanofluids) at different operating pressures and different nanoparticle mass concentrations. The experimental apparatus is a miniature flat heat pipe (MFHP) with micro-grooved heat transfer surface of its evaporator. The experimental results indicate that the operating pressure has great influence on the nucleate boiling characteristics in the MFHP evaporator. The heat transfer coefficient and the critical heat flux (CHF) of nanofluids increase greatly with decreasing pressure as compared with those of water. The heat transfer coefficient and the CHF of nanofluids can increase about 25% and 50%, respectively, at atmospheric pressure whereas about 100% and 150%, respectively, at the pressure of 7.4 kPa. Nanoparticle mass concentration also has significant influence on the boiling heat transfer and the CHF of nanofluids. The heat transfer coefficient and the CHF increase slowly with the increase of the nanoparticle mass concentration at low concentration conditions. However, when the nanoparticle mass concentration is over 1.0 wt%, the CHF enhancement is close to a constant number and the heat transfer coefficient deteriorates. There exists an optimum mass concentration for nanofluids which corresponds to the maximum heat transfer enhancement and this optimum mass concentration is 1.0 wt% at all test pressures. The experiment confirmed that the boiling heat transfer characteristics of the MFHP evaporator can evidently be strengthened by using water/CuO nanofluids.     

Thermochemically induced binding of methyl orange to polycations containing primary amine groups

The thermochemical transformation of electrostatically formed complexes of methyl orange (MO) with polycations containing primary amine groups such as ammonium salts afforded new polymers with a high concentration of covalently bound 4‐N,N‐dimethylaminoazobenzene groups in the side chain. Poly(allylamine hydrochloride) and poly(β‐aminoethylene acrylamide hydrochloride) were employed as support polycations for MO. The transformation of sulfonate–ammonium ion pairs into sulfonamide bonds, via heating at an elevated temperature, was supported by the polymer properties before and after the thermal treatment. The polymer structure changes were monitored with elemental analysis, Fourier transform infrared, ¹H NMR, and ultraviolet–visible absorption spectroscopy, and thermogravimetric analysis. The spacer length between the backbone and azobenzene structures used as side chains strongly influenced the polymer properties before and after the heat‐induced reaction. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5898–5908, 2006     

Partial molal heat capacities of aqueous tetraalkylammonium bromides as functions of temperature

Enthalpies of solution have been measured from 5 to 85°C for aqueous tetraethyl- and tetrapropylammonium bromides, and the integral heat method is employed to evaluate for these electrolytes over a wide temperature range. Data taken from the literature have been used to evaluate for aqueous Bu₄NBr over a similar temperature range. These data, along with similar data for Me₄NBr, previously reported, have been used to evaluate absolute ionic heat capacities. While the absolute values agree only qualitatively with two other methods of division, the temperature dependences of the three methods essentially agree up to 65°C. Heat capacities due to structural effects on the solvent, obtained by subtracting the inherent heat capacities of the ions, are extraordinarily positive for all four tetraalkylammonium ions and have negative temperature coefficients, indicating that all four ions, including the tetramethylammonium ion, are structure-making ions.     

Thermodynamic properties of organic compounds in aqueous solution. II. Apparent molal heat capacities of piperidines,morpholines, and piperazines

Apparent molal heat capacities of some piperidine, morpholine, and piperazine derivatives in aqueous solution have been determined by adiabatic calorimetry in the temperature range 20–55°C and in the molality range 0.2–1m. Comparison of experimental values with those calculated through group contributions, found for monofunctional compounds, indicates strong interactions between the hydrophilic centers. An interpretation is given of the possible mechanism of this interaction. Also, values of ΔC _p for the addition reaction of proton to nitrogen centers of mono- and bifunctional organic compounds are examined.