Selective pre-concentration of selenite from aqueous samples using mercapto-silica

Silica gel modified with 3-mercaptopropyl-trimethoxysilane was used for the selective separation and pre-concentration of selenite (Se(IV)) from aqueous solutions containing Se(IV) and selenate (Se(VI)). Over a wide range of acidity, from 2 mol l⁻¹ HCl to pH 9.00, Se(IV) was taken up by the mercaptopropyl-silica with nearly 100% efficiency; Se(VI) however was unretained. Se(IV) content was determined by hydride generation atomic absorption spectrometry (HGAAS), following batch release of the selenium from the pre-concentration medium by acidic periodate. The overall pre-concentration efficiency, including both take-up and elution, in the range of 89-106%. The method was applied to spiked seawater samples containing as low as 800 ng l⁻¹ Se in selenite form. This solid-phase extraction system offers several major advantages over conventional solvent extraction procedures. It firstly exhibits high selectivity for Se(IV) over Se(VI). Using the solid-phase media, pre-concentration of Se(IV) in dilute water samples can be carried out in the field, stabilizing the selenite-selenium in a convenient form for transport and storage. In addition, selenium stored on silica is derived solely from Se(IV) overcoming problems of selenium redox speciation changes and loss during storage.     

Novel Fabrication of Conductive Polymers Contained Micro‐Array Gas Sensitive Films Using A Micromanipulation Method

A novel method for fabricating a micro gas sensor film on an indium tin oxide (ITO) electrode patterned using micro‐machining technology was developed. A micromanipulation system equipped with a counter electrode (Au; Ø10 μm) and a microsyringe, which was connected to a microinjection system, was first constructed. With this system, micro gas sensor arrays could be successfully prepared on ITO electrodes. Two kinds of micro gas sensor films were prepared, based on polythiophene (PTh) and poly(3‐n‐dodecylthiophene) (PD). The response behavior of conventional PTh and micro‐PTh films against NH₃ at three different operating temperatures (25, 40 and 60 °C) was investigated by measuring the resistance of the film. With the micro‐PTh film, a reversible response was observed against NH₃ when measured at 40 and 60 °C. In addition, the responsive characteristics of the microsensor films against different testing gases were examined at the three operating temperatures. The resistance of the microsensor films of PTh and PD changed considerably, depending on the type of testing gas, allowing these sensor films to be used for the detection of various gases. Furthermore, the microsensor films had a high stability compared with conventional films prepared from the same polymer.     

Determination of photoelectron attenuation lengths in calcium phosphate ceramic films using XPS and RBS

Calcium phosphate (CaP) coatings are used to improve the biological performance of an implant. A technique that is often used to measure the composition of this material is XPS. When extremely thin coatings are measured, for example to study the interface between CaP and a substrate, the quantification of the XPS results is complicated by the varying attenuation lengths (ALs) of the photoelectrons at different energies. To correct for this, AL data are needed. In this work we measured these ALs by comparing XPS yields with the coating coverage (as measured by Rutherford backscattering spectrometry). We were able to determine the AL for several calcium and phosphorus peaks. Determination of the oxygen ALs was not possible owing to diffusion of oxygen into the polymeric substrates. For the peaks that are most often used for quantification of XPS yields (the Ca 2p and the P 2p peak), we found ALs of 21.8 × 10¹⁵ atoms cm^?2 and 26.8 × 10¹⁵ atoms cm^?2, respectively. Concentration profiles near the interface, growth mode and interfacial roughness appeared to have no measurable effect on the measured ALs. For the ALs, an energy dependence with an exponent of 0.55 was found. The measured ALs are best predicted by the empirical CS1 equation of Cumpson and Seah. Copyright © 2003 John Wiley & Sons, Ltd.     

Kinetic studies of nickel speciation in model solutions of a well-characterized humic acid using the competing ligand exchange method

Publications on the binding characteristics of metals with humic acid (HA) are sparse. Here we investigated the release of nickel from Ni(II)-HA complexes using model solutions of three different [Ni(II)]/[HA] mole ratios at three different pH values; we also compared the results with those of [Ni(II)]/[FA] complexes from previous work in this laboratory. Ligand exchange kinetics using the competing ligand exchange method (CLEM) were studied using two different techniques: graphite furnace atomic absorption spectrometry (GFAAS) with Chelex 100 resin as the competing ligand, and adsorptive cathodic stripping voltammetry (AdCSV) with dimethylglyoxime as the competing ligand to measure the rate of dissociation of Ni(II)-HA complexes. The results of the kinetic studies showed that as the [Ni(II)]/[HA] mole ratio was decreased, the rate of dissociation of Ni(II)-HA complexes decreased, and the proportion of free Ni²⁺ ions plus very labile nickel complexes decreased while the proportion of the less labile kinetically distinguishable components increased. Generally, the rate of dissociation of Ni(II)-HA complexes was slower than that of Ni(II)-FA complexes. Studies on the validity of the kinetic model showed that the concentrations of chemical species varied in a reasonable way with pH and the [Ni(II)]/[HA] mole ratios, indicating that the kinetically distinguishable components have chemical significance and the kinetic model is valid.     

Detection of perfluorocarbons using ion mobility spectrometry

An ISAS custom-designed ion mobility spectrometer equipped with a ionization source is used for the sensitive detection of traces of perfluorocarbons (PFCs, C₅F₁₂ to C₉F₂₀) in air, a class of substances for which a growing interest for industrial and environmental applications arose within the last years. Mobility spectra of the PFCs are presented, compared and discussed with regard to the possibility of identifying these analytes; detection limits are determined to be in the upper ng l⁻¹ range. Using a specific PFC as an example, a way to prevent unwanted contributions of non-product ions, the difference mobility spectrum, is introduced and described. Advantages and possibilities of this technique are briefly discussed.     

Determination of ethanol in fuel ethanol and beverages by Fourier transform (FT)-near infrared and FT-Raman spectrometries

Fourier transform-near infrared (FT-NIR) and FT-Raman spectrometries have been used to design partial least squares (PLS) calibration models for the determination of the ethanol content of ethanol fuel and alcoholic beverages. In the FT-NIR measurements the spectra were obtained using air as reference, and the spectral region for PLS modeling were selected based on the spectral distribution of the relative standard deviation in concentration. In the FT-Raman measurements hexachloro-1,3-butadiene (HCBD) has been used as an external standard. In the PLS/FT-NIR modeling for ethanol fuel analysis 50 ethanol fuel standards (84.9-100% (w/w)) were used (25 in the calibration, 25 in the validation). In the PLS/FT-Raman modeling 25 standards were used (13 in the calibration, 12 in the validation). The PLS/FT-NIR and FT-Raman models for beverage analysis made use of 24 standards (0-100% (v/v)). Twelve of them contained sugars (1-5% (w/w)), one-half was used in the calibration and the other half in the validation. Different spectral pre-processing were used in the PLS modeling, depending on the type of sample investigated. In the ethanol fuel analysis the FT-NIR pre-processing was a 17 points smoothed first derivative and for beverages no spectral pre-processing was used. The FT-Raman spectra were pre-processed by vector normalization in the ethanol fuel analysis and by a second derivative (17 points smoothing) in the beverage analysis. The PLS models were used in the analysis of real ethanol fuel and beverage samples. A t-test has shown that the FT-NIR model has an accuracy equivalent to that of the reference method (ASTM D4052) in the analysis of ethanol fuel, while in the analysis of beverages, the FT-Raman model presents an accuracy equivalent to the reference method. The limits of detection for NIR and Raman calibration models were 0.05 and 0.2% (w/w), respectively. It has also been shown that both techniques, present better results than gas chromatography (GC) in evaluating the ethanol content of beverages.     

Identification of anthraquinone coloring matters in natural red dyestuffs by high performance liquid chromatography with ultraviolet and electrospray mass spectrometric detection

Reversed phase liquid chromatography with diode array detection (DAD) and electrospray mass spectrometric (ESI MSD) methods were developed for the identification of anthraquinone color components of cochineal, lac dye, and madder – red natural dyestuffs. Electrospray mass spectrometry was found to be more suitable than diode array detection for such analysis because of its higher sensitivity (detection limits in the range 30–90 ng mL^–1) and selectivity. The developed method permitted unequivocal identification of carminic acid and laccaic acid A as coloring matters in examined preparations of cochineal and lac dye, respectively. In madder more chemical color species were found: alizarin, purpurin, lucidin, ruberythric acid, and also aluminum and calcium alizarin lake. Among the methods recommended so far, the present one allows fast, direct, and unequivocal identification of components of very complicated natural products used in art.     

Concurrent solvent recondensation large sample volume splitless injection

Concurrent Solvent Recondensation Large Sample Volume (CRS‐LV) splitless injection overcomes the limitation of the maximum sample volume to 1–2 μL valid for classical splitless injection. It is based on control of the evaporation rate in the vaporizing chamber, utilization of a strong pressure increase in the injector resulting from solvent evaporation, and greatly accelerated transfer of the sample vapors from the injector into the inlet of an uncoated precolumn by recondensation of the solvent. The sample vapors are transferred into the column as rapidly as they are formed in the injector (concurrent transfer). 20–50 μL of liquid sample is injected with liquid band formation. The sample liquid is received by a small packing of deactivated glass wool positioned slightly above the column entrance at the bottom of the vaporizing chamber. Solvent evaporation strongly increases the pressure in the injector (auto pressure surge), provided the septum purge outlet is closed and the accessible volumes around the vaporizing chamber are small, driving the first vapors into the precolumn. Transfer continues to be fast because of recondensation of the solvent, obtained by keeping the oven temperature below the pressure‐corrected solvent boiling point. The uncoated precolumn must have sufficient capacity to retain most of the sample as a liquid. The experimental data show virtually complete absence of discrimination of volatile or high boiling components as well as high reproducibility.