直接甲醇燃料电池阴极电催化剂的研究进展

直接甲醇燃料电池(DMFC)功率密度高，燃料甲醇价格低廉、储存和携带方便，特别适合作为电动车和小型电子设备的电源，是目前燃料电池研究领域的一个热点。本文介绍了40年来DMFC阴极电催化剂的发展历史及现状，并针对目前严重影响DMFC性能的“甲醇透过”问题，阐述了研制耐甲醇阴极电催化剂的重要性，讨论了今后DMFC阴极电催化剂的发展趋势。     

吸热碳氢燃料裂解镧改性混合型催化剂的研究

制备了吸热型碳氢燃料NNJ-150和镧离子交换改性的USY、ZSM-5分子重申及混合分子筛，考察了NNJ-150在USHY、HZSM-5和两者混合物以及镧改性单分子筛和混合分子筛催化剂上的裂解反应。结果表明，ZSM-5分子筛中添加镧，对NNJ-150的单分子裂解反应有明显影响；混合分子两种分子筛之间存在协同作用，低温（500℃）下，LaUSY LaZSM-5（75：25）混合分子筛对低碳烯烃的选择性较高（41.48％），催化剂寿命较长（35min以上），能有效提高吸热型碳氢燃料NNJ-150的吸热能效。     

Composition of <Emphasis Type="Italic">Carlina acanthifolia</Emphasis> Root Essential Oil

The root of Carlina acanthifolia All. (Asteraceae) contained 1.0% of essential oil (expressed in g per 100 g of dried plant material). Using GC and GC/MS, nine components were identified (100% of total oil). The structure of benzyl 2-furylacetylene (carlina oxide), which is the principal component of the oil (91.5%), was spectrometrically identified. __________ Published in Khimiya Prirodnykh Soedinenii, No. 4, pp. 331–332, July–August, 2005.     

STUDIES ON TUNG OIL COATED REGENERATED CELLULOSE FILMS WITH WATERRESISTANCE

Regenerated cellulose films with water-resistance were obtained by an improved method ofpreparing cellulose cuoxam solution from pulps of agricultural wastes (linters, wheat straw, reedand Bamao). Experimental results showed that the mechanical properties of both the dry. and wetfilms were excellent. Data from IR, SEM and tensile strength measurements implied that thesignificant improvement of water-resistance of the films was due to the cohesion between the thinTung oil covers with hydrophobicity and the regenerated cellulose films. The films werecompletely biodegraded after being buried in soil for 100 days. The transmittance of the filmsderived from linter and reed in visible band range were 80-90%.     

GC-MS Analysis of the Essential Oil from the Oleoresin of Pistacia atlantica var. mutica

The oleoresin of Pistacia atlantica var. mutica, growing in different regions of Iran, is a popular naturally occurring chewing gum and has been used traditionally in the treatment of peptic ulcer. The GC-MS analysis of the essential oil, obtained from steam distillation of the oleoresin of P. Atlantica var. mutica, has led to the identification and quantification of eleven terpenoids, -pinene (70%), -pinene (1.94%), 3-carene (0.2%), carveol (2.18%), epoxypinene (2.15%), limonene oxide (9%), myrtenol (5.31%), limonene (0.62%), citral (5.72%), -phellandrene (0.2%), and -myrcene (0.3%). The total amount of essential oil obtained was 22% v/w which is higher than any other species of the genus Pestacia.     

Cellulose-precursor synthesis of nanocrystalline Ce<Subscript>0.8</Subscript>Gd<Subscript>0.2</Subscript>O<Subscript>2−δ</Subscript> for SOFC anodes

Developments of intermediate-temperature solid oxide fuel cells (IT SOFCs) require novel anode materials with a high electrochemical activity at 800–1070 K. The polarization of cermet anodes, made of nickel, ceria and yttria-stabilized zirconia (YSZ) and applied onto a YSZ solid electrolyte, can be significantly reduced by catalytically active ceria additions, the relative role of which increases with decreasing temperature. Further improvement is observed when using Ce_0.8Gd_0.2O_2– (CGO) having a high oxygen ionic conductivity instead of undoped ceria, owing to enlargement of the electrochemical reaction zone. Nanocrystalline CGO powders with grain sizes of 8–35 nm were thus synthesized via the cellulose-precursor technique and introduced into Ni–CGO–YSZ cermets, and tested in contact with a (La_0.9Sr_0.1)_0.98Ga_0.8Mg_0.2O_3– (LSGM) electrolyte at 873–1073 K. The results showed that the anode performance can be enhanced by additional surface activation, in particular by impregnation with a Ce-containing solution, and also by incorporation of YSZ, which probably acts as a cermet-stabilizing component. The overpotential of the surface-modified Ni–CGO (25 wt%–75 wt%) anode in a 10% H₂/90% N₂ atmosphere was approximately 110 mV at 1073 K with a current density of 200 mA/cm².Presented at the OSSEP Workshop Ionic and Mixed Conductors: Methods and Processes, Aveiro, Portugal, 10–12 April 2003     

Determining the wax content of crude oils by using differential scanning calorimetry

By the use of differential scanning calorimetry (DSC), a new method to measure the wax content of crude oil has been developed. In this paper, the wax content of a crude oil is proposed and proved to be the Q (total thermal effect of wax precipitation in sample) ratio of the crude oil and its corresponding wax obtained by using standard acetone method, i.e. Q_oil/Q_wax. For the 14 studied crude oils with the wax content ranging from 1 to 27 wt.%, the wax contents determined by the presented method are in good agreement with those determined by standard acetone method, with an absolute average deviation of only 0.82 wt.%. This method has an advantage over reported DSC methods in which the exact dissolution or precipitation enthalpy of wax is a must. It is also found that the wax contents determined by either of the two methods show good linear relationship with the total thermal effect Q_oil, with the correlation coefficients over 0.96. According to the empirical correlations, the wax content of a crude oil can be easily determined by using the DSC total thermal effect Q_oil. In addition and more significantly, the new method can be applied to improve the accuracy in determining the amount of precipitated wax in a waxy crude oil at different temperatures.     

Ultra-fast essential oil characterization by capillary GC on a 50 microm ID column

A 5 m x 50 microm capillary column with 0.05 microm stationary phase film thickness, with a calculated efficiency of almost 20,000 plates per metre (under optimum conditions), was used for very fasthigh resolution GC analysis of lime essential oil. The total analysis time of this volatile essential oil was less than 90 s. Fast GC is shown to be appropriate for essential oil quality assurance analysis, and quantitative results of key components are comparable with those obtained by using conventional GC analysis. The fast GC analysis is approximately 33 times faster than the conventional GC method.     

四氢呋喃-水-乙醇三元溶液体系制备高合金化Pt-Ru/CMK-3催化剂

提出了在四氢呋喃(THF)、H2O和乙醇三元体系中用一般的化学还原法在室温下制备高合金化Pt-Ru/CMK-3催化剂的新方法. 与在纯水中制得的商品化ETEK催化剂相比, 其Pt-Ru粒子的合金化程度高、平均粒径较小且相对结晶度低, 因此, 该催化剂对甲醇氧化的电催化活性远高于在纯水中制得的Pt-Ru催化剂. 高合金化程度的原因是H2PtCl6和RuCl3在THF、H2O和乙醇三元溶液体系中的起始还原电位相近. 此外, CMK-3以其规整的二维有序孔道结构, 为直接甲醇燃烧电池(DMFC)中电子和物质的传输提供了方便的路径, 其巨大的比表面积也为Pt-Ru 纳米粒子的均匀分散提供了良好的载体.     

原油溶胶-凝胶等温转变过程中的流变性研究

使用RS75流变仪，采用小振幅振荡剪切方法和稳态剪切方法对含蜡原油在溶胶 -凝胶等温转变过程中的流行了研究．结果表明，等温转变成的凝胶原油的结构在 很大程度上决定于预剪切速率，非牛顿含蜡原油在结构恢复过程中表现出不可逆的 触变特性．而凝胶原油在外力作用下向溶胶状态转变的过程中，要经历从线性粘弹 性变形，到非线性粘弹性变形，再到结构屈服的过程，且高剪切应力下的溶胶原油 结构与预剪切速率无关．