Synthesis and Thin Film Phase Behaviour of Functional Rod‐Coil Block Copolymers Based on Poly(para‐phenylenevinylene) and Poly(lactic acid)

We report the synthesis of a series of block copolymers consisting of a rod‐like semiconducting poly(2,5‐di(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene) (DEH‐PPV) block and a flexible poly(lactic acid) (PLA) block that can be selectively degraded under mild conditions. Such selectively degradable block copolymers are designed as self‐assembling templates for bulk heterojunction donor–acceptor layers in organic solar cells. A lamellar microphase‐separated domain structure was identified for block copolymers with PLA volume fractions between 29 and 79% in bulk and thin films using SAXS, TEM, and AFM. Depending on the ratio of the two blocks we find either lamellae oriented parallel or perpendicular to the substrate in thin films.

     

Role of Sb incorporation on the electrical and photoelectrical properties of Se-In glassy alloy

Amorphous thin films of Se₉₀In_10-xSb_x (x = 0, 2, 4 and 6 at.%) have been prepared by vacuum evaporation technique. The dark and photo-conductivity measurements were carried out in all the thin films under study. Temperature dependence of conductivity in dark as well as in presence of light show that conduction is through a thermally activated process in both the cases. A discontinuity in various photoelectrical parameters is observed at 2 at.% of Sb concentration which could be correlated with average coordination number at this particular composition. The obtained results are explained on the basis of chemically ordered network model and the topological model.     

Fabrication of two-dimensional lattices by using photosensitive sol-gel and four-beam laser interference

This work demonstrates a promising method to fabricate 2D lattices by using photosensitive sol-gel method combining with four-beam of a 350.7 nm Kr ion laser interference. Photosensitive TiO₂ gel films with chelate complexes as precursors are fabricated. The characteristics of UV and IR spectra of the films and their variations in the process of laser irradiation are investigated. The results show that the gel films had an absorption peak at about 358 nm due to the formation of chelate complex. This peak gradually decreases with irradiation in time, which indicates the photosensitive properties of the TiO₂ films. A flexible four-beam interference system is proposed. Given incident angles 20.5° and 44.5°, the lattices with pitch of 700 nm and 326 nm are fabricated, respectively. The diffraction phenomenon of the 700 nm lattices is investigated by inverse method. The results are fully consistent with the 2D crystal diffraction theory.     

基于二维结构薄膜的偏振选择相位光栅的研究

利用二维结构薄膜构建了具有偏振选择特性的新型相位光栅,借助严格耦合波分析(RCWA)方法计算了光栅各级衍射强度随入射光波长及入射角的变化,发现在垂直入射情况下,波长600—640 nm范围内,相位光栅对横向电学(TE)模主要产生0级衍射,而对横向磁学(TM)模产生±1级衍射,在波长633nm处,0级衍射光的偏振消光比为109.8,±1级衍射光的偏振消光比为334.6.利用时域有限差分方法对这种相位光栅的偏振分束现象进行了模拟,偏振分离角在玻璃基板内可以达到10°左右,最后模拟了入射角为23°时光栅对不同偏     

氢气流量对混合物理化学气相沉积法制备MgB_2超薄膜的影响

用混合物理化学气相沉积法(Hybrid physical-chemical vapor deposition简称为HPCVD)制备了MgB2超薄膜.在背景气体压强、B2H6的流量和成膜时间等条件一定的情况下,当氢气的流量从200到400sccm范围内变化时,观察了其对成膜的影响.结果显示,随氢气流量增大,膜表面粗糙度增大,同时膜面的连接性变好,伴随着样品的超导转变温度得到提高.对于平均厚度是10nm和15nm的样品,氢气流量分别是200sccm和300sccm时,Tc分别是26K和33K与28K和37K.     

微量Mg掺杂ZnO薄膜的光致发光光谱和带隙变化机理研究

利用射频磁控溅射(RF-MS)法在450℃玻璃基底上制备了Mg掺杂量分别为0.81at%,2.43at%和4.05at%的ZnO薄膜,对其微观结构、室温光致发光光谱(PL)、光学和电学性质进行了研究.结果发现,微量Mg掺杂ZnO薄膜晶体具有六方纤锌矿结构并保持高结晶质量;掺杂0.81at%和2.43at%Mg的ZnO薄膜室温PL谱中近带边发射(NBE)峰的短波方向出现了高能发射带与NBE峰同时存在;随着Mg掺杂量增加至4.05at%,这个高能发射带逐步将NBE峰掩盖.推测在Mg掺杂ZnO薄膜中,Mg2+替代Zn2+附近核外电子的能量增大并产生了一个高能级.而未被Mg2+替代的Zn2+周围的核外电子能量状态不变,带间能级依然存在,随着Mg掺杂量的增加处于高能级的电子数目逐步增加并占绝对优势.因此,ZnO薄膜随着Mg掺杂量增加薄膜禁带宽度增大,这是由于Mg掺杂后周围电子能量增大与Burstein-Moss效应共同作用的结果.另外,薄膜在可见光区域的平均透射率均大于85%,随着Mg掺杂量的增加,薄膜禁带宽度增大并在3.36—3.52eV内变化;Mg掺杂量为0.81at%,2.43at%和4.05at%时,薄膜电阻率分别为2.2×10-3,3.4×10-3和8.1×10-3Ω.cm.     

Cu/TiOx复合薄膜的电子态分析及其对亲水性的影响

在室温下,采用射频磁控溅射法制备了Cu/TiO_x纳米晶复合薄膜.利用X射线粉末衍射（XRD）、X射线光电子能谱（XPS）对其结构进行表征,并研究了Cu/TiO_x复合薄膜的UV-vis吸收谱和亲水性.结果表明,退火前后薄膜中钛元素皆以Ti³⁺形式存在.薄膜在可见区有吸收,吸收限为600 nm左右.Cu/TiO_x复合薄膜具有良好的亲水性.这主要是由于Cu的掺杂,使得薄膜的性能的亲水性变好. 关键词： x复合薄膜')" href="#">Cu/TiO_x复合薄膜 射频磁控溅射 XPS 亲水性     

纳米金表面修饰与表面等离子体共振传感器的相互作用研究

为了分析纳米金表面修饰对表面等离子体共振(SPR)的放大作用,以及其对传感器本身的影响,首先,基于色散介质的吸收理论,通过建立波长型SPR生物传感器四层膜结构的数学模型,理论分析了传感器表面所吸附纳米金对传感器的影响:纳米金的表面修饰,改变了表面等离子体传感器中棱镜表面各介质层内电磁场的能量分布,削弱了金属膜在共振吸收中的作用,从而使SPR曲线的半波宽度增加,最小反射系数增大,金膜的最优膜厚度也随之改变.其次,通过不同厚度的金膜外吸附纳米金的对比试验,验证了此理论.金膜厚45nm、表面修饰10nm纳米金颗 关键词： 表面等离子体共振 生物传感器 纳米金 金属膜     

氢化硅薄膜光吸收近似特性研究

利用等离子体化学气相沉积系统在直流电压源和射频源的双重激励下,以康宁7059玻璃为衬底制备了氢化硅薄膜．过测定氢化硅薄膜Raman光谱,对薄膜微结构进行了表征;建立氢化硅薄膜的光吸收模型,计算出薄膜的光吸收系数和光学带隙,和实验结果基本一致,说明该模型符合实验结果;并利用该模型计算的光吸收系数和光学带隙,结合AMPS软件对设计的太阳电池结构进行了模拟,给出的I-V特性曲线变化趋势与实验结果基本符合,同时对实验结果与模拟结果存在差异的原因进行了分析,并给出合理解释． 关键词： 氢化硅薄膜 光吸收系数 光吸收模型     

应用核磁共振进行聚驱后泡沫驱油特性研究

采用并联岩心进行聚驱后泡沫驱油实验,利用核磁共振技术,对驱替后岩心的不同直径孔隙内的流体分布进行了研究,得到了水驱、聚合物驱、泡沫驱替阶段的驱出油的孔径范围以及剩余油分布.实验结果表明,与水驱和聚合物驱相比,泡沫驱增大了波及的孔径的范围.泡沫可以在水驱和聚驱易发生窜流的大孔径通道形成封堵,从而波及到了水驱和聚驱未波及到的孔径,不但大幅度的提高了低渗岩心的采收率,也驱出了部分高渗岩心的小孔径的油.