泡沫铅对VRLA电池负极活性物质结构及性能影响

0引言随着36V/42V汽车电源系统的提出,新一轮汽车用电池的竞争不断加剧。从目前情况看,铅酸电池由于具有成本低廉,使用可靠,原材料来源丰富,铅回收率可高达98%等优点,因此成为电动车电源最实际的选择之一[1]。但作为电动车用电池,需要克服其比能量低、充电接受能力差和负极硫酸盐化等缺点。为此各国科学家开展了大量的研究工作。最近报道用铸造多孔体作为敞口铅酸电池的集流体,它的比表面积为14cm2·cm-3,正极活性物质利用率上升到50%,远高于传统的铸造板栅[2]。在铅酸电池集流体研究领域里另一个重大进步,就是以R V C(R etic-ulated V i…     

有机硅耐磨透明涂层的固化分析

ＦＴＩＲ、ＴＧ、ＴＢＡ等对有机硅耐磨涂料（有机硅溶胶）的热固化过程研究表明有机硅胶体中缔合羟基间的脱水缩合速率很高；羟基脱水程度与固化温度有关，温度越高，达平衡时羟基的浓度越低，在１０５～１３０℃间羟基的浓度变化最大，加入适当的固化剂，对羟基的脱水交联有促进作用，在较高的固化温度下，反应体系中出现了环氧环异构化产生的酮羰基的吸收峰     

Preparation and Properties of Anti-Reflection/Anti-Static Thin Films for Cathode Ray Tubes Prepared by Sol-Gel Method Using Photoirradiation

A new technique for preparing anti-reflection/anti-static thin films for CRTs at low temperature has been developed. Double-layered films of SiO₂/SnO₂ were formed on a CRT panel surface by the sol-gel method using photoirradiation. The new method makes it possible to reduce heat treatment temperature (°C) by almost 50% and treatment time to approximately 33% of the conventional levels.     

Y_2O_3∶Eu~(3+)薄膜的制备及发光性能的研究

以稀土氧化物为原料,用溶胶-凝胶法制备前驱液,加入适量的聚乙烯醇做成膜物质,用浸渍拉提法在石英玻璃表面上得到均匀的薄膜,然后经过适当的干燥和热处理得到Y2O3∶Eu3+发光薄膜.讨论了Eu3+的掺杂浓度和热处理温度对薄膜发光性能的影响.试验表明:Eu3+的最佳掺杂浓度为8%(摩尔分数),薄膜的发光性能随热处理温度提高而增强,当热处理温度达到700℃后,薄膜的发光性能基本上稳定.同时用原子力显微镜和X射线衍射分析了薄膜的表面形貌和结构.     

Tribological properties of ormosil coatings

Transparent plastics are not scratch resistant. The damage leads to a loss of optical properties. Coatings prepared using either tetraethoxysilane or colloidal silica particles embedded in glymo is a way to avoid these disadvantages. Tribological experiments are carried out to better understand the surface modification due to a sliding friction. It is shown that the wear track is not directly related to usual mechanical properties such as Young's modulus and the hardness of the coating. The different stages leading to material loss are discussed in term of particle removal and debris circulation (accumulation or elimination) through the friction track. The mechanical properties of the film combined with the film to substrate adhesion are expected to play an important role as it can be deduced from results obtained as a function of the coating composition.     

水溶性含C_(60)聚电解质的制备及其与重氮树脂自组装膜AFMFFM的初步研究

通过BPO引发的溶液聚合 ,合成了水溶性的星状C6 0 苯乙烯 苯乙烯磺酸钠的三元共聚物 [Star shapedC6 0 poly(St SS) ],运用自组装技术 ,在水溶液中 ,含C6 0 的三元共聚物与重氮树脂 (Diazoresin)通过正负离子间的吸附力在云母基片上交替一层一层有序地组装成固体膜 .自组装膜经紫外光幅照反应 ,通过重氮基的分解 ,层间连接的离子键转变成共价键 ,从而增加薄膜的稳定性和堆砌密度 .用原子力显微镜 摩擦力显微镜(AFM FFM)考察了C6 0 在膜中的承载作用及比较不同链结构、不同链长、不同层数自组装膜的表面形貌和微摩擦性能 .初步的研究结果显示了聚合物薄膜的微摩擦性能与聚合物的化学结构、链长和膜的层数有密切关系     

具有平整表面的定向纳米碳管膜的制备

为了获得表面平整的定向纳米碳管，通过化学及物理的方法将纳米碳管膜进行反转，使其原来的AAO模板底面成为新的表面，用溶液逐步去除表面的铝和氧化铝后，获得了平整的定向纳米碳管膜表面，从而可将其作为工作面使用. 还比较了5％NaOH和6%H₃PO₄＋1.8%H₂CrO₄溶液去除氧化铝的效果.     

Characterization of Carbon Film Electrodes for Electroanalysis by Electrochemical Impedance

The interfacial behavior of electrodes fabricated from carbon film resistors of 2 and 20 Ω in supporting electrolyte solutions of varying pH used in electroanalytical experiments has been characterized by electrochemical impedance spectroscopy with complementary cyclic voltammetric experiments. Equivalent circuits are proposed to fit the experimental data and the influence of electrode pretreatment has also been investigated.     

表面膨胀粘度的测定研究

用不同浓度的NaCl和表面活性剂直链的十二烷基苯磺酸钠(LAS)、稳定剂聚丙烯酰胺和水所组成的泡沫体系为研究对象,通过表面压松弛的方法,利用计算机数据拟合,得到了计算表面膨胀粘度的方法。     

乙二胺铜－铁氰复合修饰电极薄膜的电沉积和结构表征及电化学性质

乙二胺铜－铁氰复合修饰电极薄膜的电沉积和结构表征及电化学性质陈昌国，李海梅，黄宗卿（重庆大学化工学院重庆６３００４４）关键词：铜、乙二胺，铁氰，修饰电极，光谱普鲁士兰（ＰＢ）修饰电极因其独特的电致变色现象而倍受关注。在１９７８年以来的十余年间里已相继...