An analysis of avidin, biotin and their interaction at attomole levels by voltammetric and chromatographic techniques

The electroanalytical determination of avidin in solution, in a carbon paste, and in a transgenic maize extract was performed in acidic medium at a carbon paste electrode (CPE). The oxidative voltammetric signal resulting from the presence of tyrosine and tryptophan in avidin was observed using square-wave voltammetry. The process could be used to determine avidin concentrations up to 3 fM (100 amol in 3 l drop) in solution, 700 fM (174 fmol in 250 l solution) in an avidin-modified electrode, and 174 nM in a maize seed extract. In the case of the avidin-modified CPE, several parameters were studied in order to optimize the measurements, such as electrode accumulation time, composition of the avidin-modified CPE, and the elution time of avidin. In addition, the avidin-modified electrode was used to detect biotin in solution (the detection limit was 7.6 pmol in a 6 l drop) and to detect biotin in a pharmaceutical drug after various solvent extraction procedures. Comparable studies for the detection of biotin were developed using HPLC with diode array detection (HPLC-DAD) and flow injection analysis with electrochemical detection, which allowed biotin to be detected at levels as low as 614 pM and 6.6 nM, respectively. The effects of applied potential, acetonitrile content, and flow rate of the mobile phase on the FIA-ED signal were also studied.     

低钴AB5型稀土系贮氢电极合金的研究

为了进一步降低AB5型混合稀土系贮氢合金的成本,采用Cr,Si,Cu替代Co和调节化学计量比的方法制备低钴AB5型贮氢合金。结果表明:3种取代元素在寿命方面的效果依次为Si>Cr>Cu,在放电容量和活化性能方面依次是Cu>Cr>Si。Cr,Cu,Si只有少量的替代才可能发挥其有利影响;通过非化学计量比的调节,低钴混合稀土系贮氢电极合金的放电容量、活化性能及倍率放电能力都能较好地达到实用要求,但是循环寿命有待提高。     

Fluorescence Analysis in Microarray Technology

Fluorescence has been the preferred choice for data quantification in biomedical microarray formats since their earliest days. As much as the formats have grown and evolved over the years, the methods in optical analysis have become ever more sophisticated and complex in order to produce more and better output. This review will provide an insight into the most common methods and the state-of-the-art of all areas in microarray fluorescence analysis. Starting with an overview on microarray formats with a focus on their demands on the readout, the most common and useful organic fluorescent stains are discussed before proceeding on to other approaches; the use of semiconductor nanocrystals (quantum dots), polymer and silica nanoparticles and fluorescent proteins. Ways to enhance the intrinsically low signal on biochips have become increasingly important as they offer a sound approach towards the detection of low concentration sample content. The three main categories are presented: amplification using DNA, enzymes, and dendrimers. As much diversity as on the microarrays themselves can be found at the detection device. Standard optical microarray detectors, and non-standard methods using fluorescence anisotropy, fluorescence lifetime imaging (FLIM) and fluorescence resonance energy transfer (FRET), and their advantages and disadvantages are discussed.     

Preparation and Characterization of Nanotitanium Dioxide Coating Film Doped with Fe^3＋ Ions on Porous Ceramic

The nanotitanium dioxide （TiO2） photocatalytic and porous ceramic filtering technique is one of the advanced methods to effectively treat organic wastewater. The TiO2 sol doped with Fe^3＋ ions was prepared by sol-gel processing. The influences of the process conditions of coating nanophotocatalytic material- Fe^3＋-TiO2 film on the surface of porous ceramic filter by dipping-lift method on the performance of porous ceramic filter were studied. The porous ceramic filters have two functions at the same time, filtration and photocatalytic degradation. The results of this study showed that the pH and viscosity of the sol, amount of Fe^3＋ ions doped as well as the coating times greatly affect the quality of coating film, the performance parameters and the photocatalytic activity of the porous ceramic filter. When the pH of the sol is 3-4, the viscosity is about 6 mPa.S, the amount of doped Fe^3＋ ions is about 2.0 g/L, the porous ceramic filter has been shown to have the best filtering performance and photocatalytic activity. In this condition, the porosity of porous ceramic is about 42.5%, the pore diameter is 8-10μm. The degradation of methyl-orange is 74.76% under lighting for 120 rain.     

改进的单纯形优化法用于混合稀土的同时测定

本文应用改进的单纯形优化法较好地弥补了目前在分析化学计量学中得到广泛应用的卡尔曼滤波法所存在的不足，交法应用于混合稀土的同时测定中，获得了满意的结果，结果准确度较卡尔滤波法的有显著的提高。     

Determination of trace elements in ambient aerosol samples

A microwave-assisted digestion procedure using HNO₃, HF, and H₂O₂ has been developed for analysis of elements in ambient particulate matter (PM). The samples are collected on cellulose filters and analyzed by inductively coupled plasma mass spectrometry (ICP-MS). The ICP-MS is calibrated with external standards, and recovery of analytes is tested with NIST SRM 1648 Urban Dust. This method has been used to quantify the airborne concentrations of a large number of elements, including Ag, As, Ba, Be, Ca, Cd, Ce, Co, Cr, Cs, Cu, Fe, Ga, K, Li, Mg, Mn, Mo, Ni, Pb, Rb, Se, Sb, Sr, Ti, Tl, V, and Zn. For the majority of these elements, recovery of the NIST SRM is within 15% of the certified values.     

液相组合合成的纯化方法

综述了近8年来液相平行合成和组合合成中应用的不同技术, 包括可溶性载体、氟合成技术、离子液体、固相试剂树脂以及低聚乙烯二醇(OEG)衍生物的应用等几方面内容. 论述了它们的基本原理以及相关的应用实例, 并着重强调了目标化合物的分离纯化方法.     

Application of an Ion Beam Technique for the Design of Visible Light-Sensitive, Highly Efficient and Highly Selective Photocatalysts: Ion-Implantation and Ionized Cluster Beam Methods

As a new concept for the design of effective photocatalysts, an ion beam technology using accelerated metal ions, a metal ion implantation and an ionized cluster beam (ICB) method, have been applied to design unique photocatalysts. The metal ion implantation of TiO₂ and Ti-containing zeolites with highly accelerated metal ions (V⁺, Cr⁺, etc.) is useful in designing photocatalysts that can operate efficiently under visible light irradiation. Also, an ICB method with a low acceleration energy is useful in preparing transparent TiO₂ thin films on various types of substrates for the efficient photocatalytic degradation of pollutants diluted in water and air. The combination of the ICB method and metal ion implantation can develop the TiO₂ thin films that are able to operate not only under UV light but also under visible light irradiation.     

口腔癌相关唾液肿瘤生物标志物的分析检测研究进展

口腔癌系头颈部癌，癌组织均位于口腔内，其非侵入性早期诊断是减少该病死亡的有效手段.唾液系口腔癌变相关物质首先释放进入的体液，取材方便，安全无创，是口腔癌普查筛选、早期诊断的首选指标.本文对唾液肿瘤生物标志物的种类、目前国内外常用的检测方法进行概述，重点阐述新型电化学生物传感方法在口腔癌相关唾液肿瘤生物标志物检测方面的相关应用及其最新研究进展.并对口腔癌相关唾液肿瘤生物标志物电化学传感技术的未来发展方向提出展望，拟为其深入研究与应用提供参考.     

Pretreatment of swine wastewater using anaerobic filter

Efforts were made to assess the efficiency of an anaerobic filter packed with porous floating ceramic media and to identify the optimum operational condition of anaerobic filter as a pretreatment of swine wastewater for the subsequent biological removal of nitrogen and phosphorus. A stepwise decrease in hydraulic retention time (HRT) and an increase in organic loading rate (OLR) were utilized in an anaerobic filter reactor at mesophilic temperature (35°C). The optimum operating condition of the anaerobic filter was found to be at an HRT of 1 d. A soluble chemical oxygen demand (COD) removal efficiency of 62% and a total suspended solids removal efficiency of 39% at an HRT of 1 d were achieved with an OLR of 16.0 kg total COD/(m³·d), respectively. The maximum methane production rate approached 1.70 vol of biogas produced per volume of reactor per day at an HRT of 1 d. It was likely that the effluent COD/total Kjeldahl nitrogen ratio, of 22, the COD/total phosphorous ratio of 47, and the high effluent alkalinity >2500 mg/L as CaCO₃ of the anaerobic filter operated at an HRT of 1 d was adequate for the subsequent biological removal of nitrogen and phosphorus.