The Reactivity of Cr‐Te Superlattice Reactants and of Co‐deposited Cr‐Te Films: Studies with in‐situ X‐ray Diffractometry

The reactivity of a Cr‐Te multilayer film consisting of 326 Cr/Te double‐layers with about 88(3) at% Te was investigated with in‐situ X‐ray diffraction. The occurrence of a superstructure reflection caused by the multilayer system is observed. During the annealing procedure between 80 and 90 °C the layer‐by‐layer arrangement is destroyed and elemental Te crystallizes. After 6 h isothermal annealing at 140 °C CrTe₃ starts to crystallize. The amount and the crystal size of CrTe₃ increase with raising temperature and Te is consumed during the growth process. At 220 °C the formation of crystalline Cr₂Te₃ is observed and between 220 and 260 °C CrTe₃ is completely decomposed into Cr₂Te₃. The two Cr tellurides grow as highly textured materials. The size of CrTe₃ crystals is significantly larger than that of Cr₂Te₃. For a co‐deposited Cr‐Te film with composition 77(3) at% Te the tri‐telluride and elemental Te crystallize simultaneously. The texture of CrTe₃ is less pronounced and different reflections of the tri‐telluride occur besides the (h00)‐reflections. Up to 160 °C a pronounced increase of the crystallite size is observed and the crystals are significantly larger than those obtained with the multifilm sample. At 130 °C the crystallization kinetics seem to be controlled by nucleation.     

Characterization of the Converging Jet Region in a Triple Torch Plasma Reactor

Enthalpy probe measurements were taken of the converging plasma plume in a triple torch plasma reactor and related to substrate heat flux measurements. Results show excellent entrainment of process gases injected into the converging plasma plume by way of the central injection probe. At lower pressures (40 kPa), the plasma volume is equivalent to at least a 3 cm diameter, 4 cm long cylinder, with relatively uniform temperature, velocity, and substrate heat flux profiles when compared to a typical dc arc jet. Converging plasma plume size, substrate heat flux, and enthalpy profiles are also shown to be a strong function of applied system power. Substrate heat flux measurements show smaller radial gradients than enthalpy probe measurements, because of the high radial velocity component of gases above the substrate boundary layer. Enthalpy probe measurements were also conducted for diamond deposition conditions and approximate temperature and velocity profiles obtained. Problems with the uniform gas mixture assumption prohibited more accurate measurements. Reproducibility of enthalpy measurement results was shown with an average standard deviation of 11.8% for the velocity and 7.6% for the temperature measurements.     

On-line enzymatic reaction,extraction, and chromatography of fatty acids and triglycerides with supercritical carbon dioxide

Supercritical carbon dioxide can be utilized both as an introduction solvent in capillary SFC and as a reaction medium; both possibilities are illustrated in this study. An off-line SFE unit was modified for on-line SFE-SFC. To facilitate rapid depressurization of the extraction cell and to prevent memory effects, a 6-port valve was installed at the outlet line of the extraction unit. An increased background signal was obtained when PEEK polymer was used in the construction of the extraction vessel; when stainless steel was used, the blanks improved. The synthesis of methyl esters and butyl esters of fatty acids from triglycerides in edible fat was examined using an immobilized lipase as a catalyst in on-line SFE-SFC. As a result of 30 minutes reaction – extraction time, high yields of fatty acid esters were obtained at a pressure of 150 bar and a temperature of 50°C.     

Thermal transitions and fat droplet stability in ice-cream mixmodel systems

We studied thermal transitions and physical stability of oil-in-water emulsions containing different milk fat compositions, arising from anhydrous milk fat alone (AMF) or in mixture (2:1 mass ratio) with a high melting temperature (AMF–HMT) or a low melting temperature (AMF–LMT) fraction. Changes in thermal transitions in bulk fat and emulsion samples were monitored by differential scanning calorimetry (DSC) under controlled cooling and reheating cycles performed between 50 and –45°C (5°C min^–1). Comparison between bulk fat samples and emulsions indicated similar values of melting completion temperature, whereas initial temperature of fat crystallization (T_onset) seemed to be differently affected by storage temperature depending on triacylglycerols (TAG) composition. After storage at 4°C, T_onset values were very similar for emulsified and non-emulsified AMF–HMT blend, whereas they were lower (by approx. 6°C) for emulsions containing AMF or mixture of AMF–LMT fraction. After storage at –30°C, T_onset values of re-crystallization were higher in emulsion samples than in bulk fat blends, whatever the TAG fat composition. Light scattering measurements and fluorescence microscopic observations indicated differences in fat droplet aggregation-coalescence under freeze-thaw procedure, depending on emulsion fat composition. It appeared that under quiescent freezing, emulsion containing AMF–LMT fraction was much less resistant to fat droplet aggregation-coalescence than emulsions containing AMF or AMF–HMT fraction. Our results indicated the role of fat droplet liquid-solid content on emulsion stability.     

Characteristics of Subtractive Anodic Stripping Voltammetry of Lead,Cadmium and Thallium at Silver‐Gold Alloy Electrodes

Silver‐gold alloy electrodes have been studied for the purpose of the quantitative determination of heavy metals by subtractive anodic stripping voltammetry, (SASV). The results have been compared with those obtained with the silver and gold electrodes. The 50/50 a/o Ag/Au alloy electrode is the most suitable for quantifying thallium in the presence of lead and cadmium. The separation of its peak from those of lead and cadmium is 200 mV, which is about twice the separation obtained on the pure metal electrodes and is also better than on mercury. The silver electrode is suitable for the simultaneous determination of thallium, lead and cadmium. The peaks of lead and cadmium overlap on the 50/50 alloy. Pure silver or pure gold can be used for simultaneous quantification of these two metals. The use of gold for quantifying lead and cadmium is more limited because the peak potential of cadmium is shifted in the negative direction as its concentration increases and at [Cd²⁺]>200 nM, the two peaks merge. SASV enables correction for background currents and is of utmost importance for obtaining well‐defined peaks. The peaks of lead, cadmium and thallium appear over a relatively narrow potential range (ca. 200 mV) on all the electrodes presented in this work. For this reason, the quantifying of a peak is based on the derivative at the inflection point of only one of its branches (ascending or descending). All SASV measurements were carried out without removal of oxygen.     

Mechanism of silicon film deposition in the RF plasma reduction of silicon tetrachloride

Plasma-chemical reduction of SiCl₄ in mixtures with H₂ and Ar has been studied by optical emission spectroscopy (OES) and laser interferometry techniques. It has been found that the Ar:H₂ ratio strongly affects the plasma composition as well as the deposition (r _D) and etch (r _E) rates of Si: H, Cl films and that the electron impact dissociation is the most important channel for the production of SiCl_x species, which are the precursors of the film growth. Chemisorption of SiCl_x and the reactive surface reaction SiCl_x+H–SiCl_(x–1)0+HCl are important steps in the deposition process. The suggested deposition model givesr _D [SiCl_x][H], in agreement with the experimental data. Etching of Si: H, Cl films occurs at high Ar: H₂ ratio when Cl atoms in the gas phase become appreciable and increases with increasing Cl concentration. The etch rate is controlled by the Cl atom chemisorption step.     

Cathodic deposition of ternary In+As+Sb alloys and formation of InAsxSb1−x

In+As+Sb alloys have been deposited onto Ni and Ti cathodes from tartaric acid solutions at pH 2. Homogeneous deposits of composition suitable for achieving InAs_xSb_1−x can be obtained from this medium. The As-to-Sb ratio can be controlled by properly selecting solution composition and deposition potential.X-ray photoelectron spectroscopy and X-ray diffraction analyses show that formation of III–V compounds occurs at room temperature. In reacts preferentially with As rather than with Sb, but crystalline phases formed at room temperature are Sb-rich. After annealing the In+As+Sb alloys at 250°C, the composition calculated from cell parameters appears similar to that measured by energy-dispersive X-ray analysis, suggesting that the entire deposit has been converted into the InAs_xSb_1−x crystalline phase.     

Investigation of nucleation processes under the influence of magnetic fields

The present work demonstrates the possibilities and the limits of the in situ electrochemical scanning tunneling microscopy for investigation of nucleation processes in magnetic fields on the examples of Cu and Co electrodeposition onto Au(111) electrodes from sulfate electrolytes with pH 3. Cyclic voltammograms of Cu in the underpotential range (UPD) exhibit no significant change in the cathodic and anodic peaks recorded in magnetic fields parallel to the surface. In magnetic fields of a permanent magnet, the reconstruction of Au has been annihilated during UPD of Cu. In the overpotential range, the dissolution of Cu is inhibited. This triggers the formation of a Cu–Au surface alloy. The UPD deposition of Co onto Au(111) could be proven without magnetic field, which leads to the formation of two monolayers. The nucleation in an applied field could not be observed due to higher induced fluctuations and microconvective effects. Contribution to special issue “Magnetic field effects in Electrochemistry”.     

Study of the first nucleation steps of thin films by XPS inelastic peak shape analysis

The initial steps in the formation of thin films have been investigated by analysis of the peak shape (both inelastic background and elastic contributions) of X‐ray photoelectron spectra. Surface coverage and averaged height of the deposited particles have been estimated for several overlayers (nanometre range) after successive deposition cycles. This study has permitted the assessment of the type of nucleation and growth mechanisms of the films. The experiments have been carried out in situ in the preparation chamber of an XPS spectrometer. To check the performance of the method, several materials (i.e. cerium oxide, vanadium oxide and cadmium sulfide) have been deposited on different substrates using a variety of preparation procedures (i.e. thermal evaporation, ion beam assisted deposition and plasma enhanced chemical vapour deposition). It is shown that the first deposited nuclei of the films are usually formed by three‐dimensional particles whose heights and degree of surface coverage depend on the chemical characteristics of the growing thin film and substrate materials, as well as the deposition procedure. It is concluded that XPS peak shape analysis can be satisfactorily used as a general method to characterize morphologically the first nanometric moieties that nucleate a thin film. Copyright © 2006 John Wiley & Sons, Ltd.     

Cadmium colloids from non-aqueous solvents

Cadmium colloids have been prepared by Chemical Liquid Deposition (CLD). The metal is evaporated to yield atoms which are solvated at liquid nitrogen temperature, and upon warming, stable liquid colloids are formed with particle size ranging between 25–100 Å. Zeta potentials were calculated according to the conversion of Hunter and the Hückel equation, for ethanol and dimethyl sulphoxide. UV/VIS measurement of most of the black colloids showed absorption band around 280 nm. For comparison, we prepared CdS colloid with size 400–625 Å. The colloids are stable to oxidation in air and/or oxygen bubbling. The synthesis of colloids and films from Cd with acetone, 2-butanone, ethanol, 2-propanol, 2-methoxyethanol, DMF and DMSO is reported. Transmission Electron Microscopy (TEM) allows us to determine particle size.