工业用水中总铁含量的快速测定

介绍了以菲咯嗪－醋酸钠－醋酸缓冲溶液为显色体系、用自制的铁含量比色测定仪快速测定工业用水中总铁含量的方法。总铁含量≤０５ｍｇ／Ｌ时，标准偏差≤００３ｍｇ／Ｌ；总铁含量＞０５ｍｇ／Ｌ时，相对标准偏差≤５％。单次测定时间（包括样品处理）为１０～１５ｍｉｎ。采用单色光源及微型流动比色池，由蠕动泵和电子线路实现自动进样，直接显示测定结果。     

锌—镉法测定天然水中硝酸盐的盐误差及其解决方法

研究了锌-镉法测定天然水中硝酸盐的盐误差,发现水中含盐量对还原率有重大影响,但在盐度为1%以后还原率基本不变;加入人工海盐(1.5g/50ml水样)可消除盐误差.由此建立了没有盐误差的新的锌-镉法.方法相对标准偏差小于3%,回收率为98%～102%,与镉-铜法对比,两种方法的相对偏差小于8%.     

Water‐in‐Crude Oil Emulsions in the Burgan Oilfield: Effects of Oil Aromaticity,Resins to Asphaltenes Content (R/(R+A)), and Water pH

Asphaltenes and resins separated from emulsion samples collected from Burgan oil field were used with heptane‐toluene mixtures as model oil to study the effect of oil aromaticity, resin content, and pH of the aqueous phase on the stability of water in model emulsions. It was confirmed that, as long as the asphaltenes are completely solubilized, increasing aromaticity leads to less stable emulsions. A consistent correlation between emulsion stability and relative resin mass content (R/(R+A)) was observed for all three of the field samples. There was a sharp decrease in stability when the R/(R+A) value exceeded 0.75. Emulsion stability was enhanced at high pH and possibly at very low pH (<2).     

Micellization of Sodium Dodecyl Sulfate in Glycerol Aqueous Mixtures

The effect of glycerol on both micellar formation and the structural evolution of the sodium dodecyl sulfate (SDS) aggregates in the context of the action mechanism of the cosolvent has been studied. The critical micelle concentration and the degree of counterion dissociation of the surfactant over a temperature range from 20°C to 40°C were obtained by the conductance method. The thermodynamic parameters of micellization were estimated by using the equilibrium model of micelle formation. The analysis of these parameters indicated that the lower aggregation of the surfactant is mainly due to a minor cohesive energy of the mixed solvent system in relation to the pure water. The effect of glycerol on the mean aggregation number of the micelles of SDS was analyzed by the static quenching method. It was found that the aggregation number decreased with the glycerol content. This reduction in the micellar size seems to be controlled by an increase in the surface area per headgroup, which was ascribed to a participation of glycerol in the micellar solvation layer. Studies on the micropolarity of the aggregates, as sensed by the probe pyrene, indicated that this microenvironmental parameter is almost unaffected by the presence of glycerol in the mixture. However, an increase in the micellar microviscosity at the surface region was observed from the photophysical behavior of two different probes, rhodamine B and auramine O. These results suggest a certain interaction of the cosolvent in the micellar solvation of SDS micelles.     

Adsorption Mechanism of Comb Polymer Dispersants at the Cement/Water Interface

Comb polymers are commonly used as dispersants to stabilize highly concentrated cement suspensions. The effectiveness of such polymeric additives to stabilize these suspensions is determined to a large extent by the amount adsorbed. In this study we investigated the adsorption characteristics of various comb dispersant containing different graft densities on surfaces of cement particle. The effect of inorganic salts on their adsorption was also examined in order to elucidate their adsorption mechanism. The results show that the adsorption of comb polymer dispersants on cement surface conforms approximately to Langmuir's adsorption isotherm and the characteristic plateau A _s and adsorption free energy ΔG_ads are largely dependent on the anionic group content of the comb polymers. The A _s and ΔG_ads increase with increasing anionic group content. This information suggests that the adsorption of comb polymers on cement surfaces is dominated by electrostatic interaction between COO-groups on the comb polymers and the positive surface of the cement. This conclusion is supported by effects of inorganics such as calcium and sulfate ions, and diffuse reflectance FTIR spectroscopy. The implication of results for tuning polymers for the required performance in cement manufacture should be noted.     

Determination of Anionic Surfactants in Water

The use of ternary complexes in the determination of anionic surfactants has been investigated and an analytical method using linear alkyl sulfonates as a test substance has been developed. The method involves the formation of the chloroform-extractable bisphenanthroline Cu(II)-linear alkyl sulfonate (LAS) complex and the subsequent equilibration of the extract with erythrosine to form the extractable bisphenanthroline Cu(II)-erythrosine complex. In the equilibration step erythrosine displaces LAS quantitatively, allowing the determination of the LAS originally present by measuring the absorbance of the extracted bisphenanthroline-Cu(II)-erythrosine complex. Results are reported of studies made to determine the optimum analytical conditions, the sensitivity, and the precision for the method described.     

Efficient and Green Method for the Synthesis of 1,5‐Benzodiazepine and Quinoxaline Derivatives in Water

Various 1,5‐benzodiazepine and quinoxaline derivatives have been synthesized in water with excellent yields using a catalytic amount of indium chloride at room temperature. This synthetic protocol is nontoxic, safe, and environmentally benign.     

Simplified Approach to the Uncatalyzed Knoevenagel Condensation and Michael Addition Reactions in Water using Microwave Irradiation

Use of microwave irradiation in the synthesis of arylidenemalononitrile and benzopyran derivatives in water without catalyst is a clean method with high yield.     

Polymers Derived from 4-Substituted Salicylic Acids as Antifungal Agents

4-Amino-, chloro-, and bromo-substituted salicylic acid-formaldehyde polymers and their metal chelates were screened for their antifungal activity. Various copolymers prepared from 4-chloro-(bromo)salicylic acid, formaldehyde, and other comonomers were also screened for their antifungal activity. All these polymers, copolymers, and polychelates were found active against several fungi Their fungicidal activities are compared with those of the corresponding monomers and monomeric chelates.     

Method Development for the Speciation of Chromium in River and Industrial Wastewater Using GFAAS

A simple, sensitive and inexpensive method for the speciation of Cr(VI) and Cr(III) in river and industrial wastewater was developed, optimized and validated. Samples were collected, filtered and then chromium species were determined in the filtrate. In the filtrate, total Cr was determined directly by Graphite Furnace Atomic Absorption Spectrometry (GFAAS). A portion of the filtered sample was buffered to pH 6.4, extracted with Amberlite LA-2/MIBK and finally Cr(VI) was determined in the organic extract and Cr(III) in the aqueous phase using GFAAS. The method was evaluated by analysis of the certified reference material, CRM 544, and good accuracy was obtained. The limit of detection for Cr(VI) and Cr(tot)/Cr(III) was found to be 0.30 and 0.08 µg L⁻¹, respectively, and a precision expressed as relative standard deviation of better than 11% was achieved for nine replicates. A number of water samples from the Tinishu Akaki River, Ethiopia, and wastewater samples from a chemical plant in Germany, were analysed. In addition to the GFAAS method, Cr(tot) was also determined using ICP-MS (in CRM 544, lyophilized water, and Tinishu Akaki River water samples) and Cr(tot) and Cr(VI) using UV-VIS spectrophotometry (in CRM 544 and industrial wastewater samples). Good agreement between the different methods was found.