Preparation of nano-hydroxyapatite/poly(<Emphasis Type="SmallCaps">l</Emphasis>-lactide) biocomposite microspheres

Nano-hydroxyapatite (HA)/poly(l-lactide) (PLLA) composite microspheres with relatively uniform size distribution were prepared by a solid-in-oil-in-water (s/o/w) emusion solvent evaporation method. The encapsulation of the HA nanopaticles in microshperes was significantly improved by grafting PLLA on the surface of the HA nanoparticles (p-HA) during emulsion process. This procedure gave a possibility to obtain p-HA/PLLA composite microspheres with uniform morphology and the encapsulated p-HA nanoparticle loading reached up to 40 wt% (33 wt% of pure HA) in the p-HA/PLLA composite microspheres. The microstructure of composite microspheres from core-shell to single phase changed with the variation of p-HA to PLLA ratios. p-HA/PLLA composite microspheres with the diameter range of 2–3 μm were obtained. The entrapment efficiency of p-HA in microspheres could high up to 90 wt% and that of HA was only 13 wt%. Surface and bulk characterizations of the composite microspheres were performed by measurements such as wide angle X-ray diffraction (WAXD), thermal gravimetric analysis (TGA), environmental scanning electron microscope (ESEM) and transmission electron microscopy (TEM).     

紫外光引发甲基丙烯酸甲酯乳液聚合

以60W高压汞灯为光源,以偶氮二异丁氰(AIBN)为主要光引发剂,以甲基丙烯酸甲酯(MMA)为单体进行乳液聚合,考察了光照时间、单体浓度、光引发剂浓度等因素对单体转化率的影响;采用透射电镜观察了乳胶粒的形态,并测定了其尺寸.结果表明,转化率随光照时间和单体浓度的增加而上升;当光引发剂质量分数为3%时单体转化率最高.     

Synthesis by Emulsion Polymerization of Poly(butyl acrylate-co-silver acrylate) Ionomers and Evaluation of their Possible Applications

The synthesis by emulsion polymerization and the characterization by a battery of techniques of poly(butyl acrylate-co-silver acrylate) [poly(BuAc-co-AgAc)] ionomers are reported here. Reaction rates were fast and conversions around 90% were obtained in less than one hour, regardless of the initial ratio of butyl acrylate and silver acrylate employed (BuAc/AgAc = 90/10, 80/20, 70/30). Particle size was in the range of 176 to 200 nm, depending on the BuAc/AgAc ratio. Ionomers’ formation was corroborated by infrared spectroscopy and inferred by differential scanning calorimetry (DSC). DSC disclosed that the poly(BuAc-co-AgAc) has two glass transition temperatures: one at ca. ?49°C due to relaxation of the ionomer backbone domains rich in BuAc and another ca. 35°C due to the relaxation of the backbone domains where the AgAc-units content was higher. Young moduli increased as the copolymers became richer in AgAc. Antibacterial tests against Escherichia coli with the 90/10 (BuAc/AgAc) ionomer revealed that the bacteria population diminishes from 5 log CFU/mL to less than 0.3 MPN/mL after one hour of contact with the ionomers. Also, we demonstrated that the ionomers are excellent compatibilizers for making semiconductive films of n-dodecylbenzene sulfonic acid-doped polyaniline (PANIDBSA)-poly(BuAc-co-AgAc) and poly(n-butyl methacrylate) (PBMA) blends. The electrical conductivity of the blend films, which were homogeneous, rose as the AgAc content in the films increased.     

Dynamic modeling of the morphology of latex particles with in situ formation of graft copolymer

Modification of the polymer–polymer interfacial tension is a way to tailor‐make particle morphology of waterborne polymer–polymer hybrids. This allows achieving a broader spectrum of application properties and maximizing the synergy of the positive properties of both polymers, avoiding their drawbacks. In situ formation of graft copolymer during polymerization is an efficient way to modify the polymer–polymer interfacial tension. Currently, no dynamic model is available for polymer–polymer hybrids in which a graft copolymer is generated during polymerization. In this article, a novel model based on stochastic dynamics is developed for predicting the dynamics of the development of particle morphology for composite waterborne systems in which a graft copolymer is produced in situ during the process. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Role of radicals in UV‐initiated postplasma grafting of poly‐ε‐caprolactone: An electron paramagnetic resonance study

Electron paramagnetic resonance (EPR) measurements were performed on poly‐ε‐caprolactone (PCL) films at different stages of the postplasma‐grafting process. PCL films prepared by solvent casting (SC) or electrospinning (ESP) yield very similar EPR spectra after Ar‐plasma treatment and subsequent exposure to air, but the EPR signal is much stronger in the PCL‐ESP films. The free radicals appear to be mainly, and possibly exclusively, oxygen centered. The radicals generated by UV irradiation in PCL‐ESP films were studied in situ with EPR, using a UV‐LED (λ = (285 ± 5) nm). Their EPR spectrum is distinctly different from the plasma‐induced signal, indicative of carbon‐centered radicals, and appears to be independent of the plasma pretreatment. UV‐induced homolytic splitting of (hydro)peroxide bonds was not observed. Both the plasma‐ and UV‐induced radicals decay at room temperature (RT), even in an inert atmosphere. This study demonstrates the potential of electrospun films and UV‐LEDs for the study of plasma‐ and UV‐generated free radicals with EPR in polyesters, and raises questions with respect to the validity of some generally accepted molecular mechanisms underpinning the postplasma grafting technique for polyesters. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Fabrication of 3D electrospun structures from poly(lactide‐co‐glycolide acid)–nano‐hydroxyapatite composites

The fabrication of three‐dimensional (3D) electrospun composite scaffolds was presented in this study. Layers of electrospun meshes made from composites of poly(lactide‐co‐glycolide acid) (PLGA) and hydroxyapatite (HA) were stacked and sintered using pressurized gas. Three HA concentrations of 5, 10, and 20 wt % were tested, and the addition of the HA nanoparticles decreased the tensile mechanical properties of the meshes with 20 wt % HA. However, after the gas absorption process, the fibers within the mesh sintered, which improved the mechanical properties more than twofold. The fabrication of 3D, porous, electrospun scaffolds was also demonstrated. The resulting 3D scaffolds had open porosity of up to 70% and modulus of ～20 MPa. This technique improves on the current electrospinning technology by overcoming the challenges of depositing a thick, 3D structure. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Nitrile Rubber Reactor Operation Troubleshooting with Principal Component Analysis

Principal Component Analysis (PCA) is employed as a tool in order to demonstrate yet another application of the technique, and, most importantly, to show that results from the statistical multivariate technique do make physico-chemical sense. The operation of a typical emulsion copolymerization of acrylonitrile and butadiene (nitrile butadiene rubber, NBR) is used as an example of process troubleshooting. In more general terms, a statistical tool is used to aid process data analysis and process operation (recipe, product property) troubleshooting.

The goal is to produce consistent Mooney Viscosity (MV) among different batches. The observation is that varying induction times lead to Mooney Viscosity inconsistencies. Firstly, we show results from the application of PCA to process data. Secondly, we deal with an even more important (and often ignored) question by examining whether the trends indicated by PCA make process sense.