Synthesis of polystyrene latex with amphoteric surfactant and its characterization

An emulsion polymerization of styrene in the presence of an amphoteric surfactant; N,N-dimethyl-n-laurylbetaine (LNB) was carried out at pH 7.0. The polymerization rate and the concentration of the latex particle were proportional to the LNB concentration of 0.6 power. The latex particle sizes became smaller with increasing concentrations of LNB. The molecular weights of polystyrene latices increased with the concentration of LNB. The zeta-potentials of latex particles were significantly dependent on the pH, and showed the existence of an isoelectric point.     

原子转移自由基聚合原位合成温敏性微球

以过硫酸钾为引发剂、丙酮-水[V(丙酮)∶V(水)＝4∶6]的混合溶剂为反应介质, 在少量二乙烯苯存在的条件下使苯乙烯(St)和对氯甲基苯乙烯(CMSt)进行无皂乳液共聚反应, 得到了粒径大小均匀的交联型聚苯乙烯(PSt)微球, 由X射线光电子能谱对表面组分测定发现: CMSt上的氯原子在聚合过程中富集于交联微球的表面. 以此交联型PSt微球为原子转移自由基聚合(ATRP)的引发剂, 在22 ℃下引发N-异丙基丙烯酰胺(NIPAAm)进行原位ATRP反应, 得到了表面原子转移自由基聚合接枝的交联聚苯乙烯(PNIPAAm-g-PSt)温敏性微球. 借助傅立叶变换红外光谱、差示扫描量热仪、扫描电子显微镜及激光光散射仪等对PNIPAAm-g-PSt的结构、相转变温度、形态及不同温度下的粒径变化进行了测定, 结果表明NIPAAm单体成功地原位ATRP接枝在交联PSt微球的表面, 接枝微球的球形更规整, 在水中的相转变温度约为32 ℃, 具有明显的温度敏感性.     

Production of submicron-size monodisperse polymer particles having aldehyde groups by seeded aldol condensation polymerization

Submicron-size monodisperse polystyrene/polyglutaraldehyde composite particles having aldehyde groups at the surfaces were produced by seeded aldol condensation polymerization of glutaraldehyde in the presence of polystyrene particles prepared by emulsifier-free emulsion polymerization. This technique is expected to be useful for the production of size-controlled polymer particles having aldehyde groups.Part CXXXVI of the series Studies on Suspension and Emulsion     

3-取代-5(3-乙基-4,5-二苯基噻唑叉)洛丹宁的增感性能

简单份菁(或称零甲川份菁)是一种可以用作卤化银感光乳剂层感蓝增感的染料。彩色正性材料的发展,要求感蓝乳剂层使用氯溴化银乳剂,并配合使用感蓝增感染料以符合感蓝区域的光谱要求。以氩离子激光为光源的电子分色片乳剂要求对波长488nm附近有较高的敏感,此种乳剂本身感色范围偏离氩离子激光发射峰。寻找增感效率高、光谱增感峰适合的感蓝染料很有必要。本文用2-甲硫基-3-乙基-4,5二苯基噻唑对甲苯磺酸盐(1)分别与3-取代洛丹宁(2)在无水乙醇存在下反应,制得六个未见文献报导的3-取代-5-(3-乙基-     

球形钴酸锂的乳液法合成及其结构、性能研究

采用一种特殊乳液法, 制备了锂离子电池正极材料球形LiCoO₂. 分别研究了一次颗粒尺寸、烧结时间对于二次造粒的影响. 还对LiCoO₂球体内部的结构进行了SEM和HRTEM研究, 发现一次颗粒非常紧密地融合在一起, 晶体边界区域没有明显的非晶相区, 也没有纳米级别的孔洞、裂缝. 电化学性能研究表明, 在900 ℃烧结4 h的材料具有较高的首次放电容量(143 mAh•g^－1)和良好的循环性能     

苯丙水溶胶的合成与性能研究(I) 聚合工艺和反应组分对聚合稳定性和胶体性能的影响

用一次投料法、半连续滴加法和单体预乳化法三种聚合工艺，合成了苯丙乳液聚合物，并加氨微细化，转化成水溶胶，考察了聚合工艺和反应组分（乳化剂，功能单体等）对苯丙乳液及其水溶胶反应稳定性和粒子大小及分布等胶体性能的影响。     

Morphology control of soap-free seeded P(St-EA-AA) latex particles

Soap-free poly(styrene-ethyl acrylate-acrylic acid) latex particles with narrow size distribution and with surface carboxyl groups were synthesized by semicontinuous emulsion polymerization, and the particles with homogeneous multihollow structure were obtained after alkali posttreatment. Effects of treatment conditions and crosslinking agents on particle morphology were investigated. Results showed that the multihollow structure can be formed inside the uncrosslinked particles only when the treatment temperature exceeded 50 °C, the pH was higher than 10.0, the amount of 2-butanone was more than 3.0 ml and the treatment time was longer than 30 min. Furthermore, the volume expansion of the particles increased with the temperature increased to 90 °C, the pH to 12.5 or the amount of 2-butanone to 7.0 ml, and this value increased first and then decreased with the treatment time prolonged. Fine pores can be generated in the shell of particles crosslinked by 0.2 g of ethyl glycol dimethylacrylate (EGDMA), while no hollow structure formed inside particles when 0.4 g of EGDMA or 0.2 g of divinyl benzene was used.     

W／O／W乳液的渗透溶胀与夹带溶胀

研究了W/O/W乳液的溶胀,实验结果表明,渗透溶胀随内外相溶液间的渗透压差、表面活性剂及载体浓度的增大而增加,但随膜粘度的增加而降低,渗透压差较高时,水渗透的影响大于夹带的影响;膜相中含氧化合物对溶胀的影响大于含氮化合物,采用Span 80作乳化剂时,比采用E 644渗透溶胀约高6倍,夹带溶胀也较高;重复聚结再分散使夹带溶胀急剧增加,因而多级混合澄清槽对液膜操作似不适用。     

反相乳液聚合制备壳聚糖接枝共聚物及应用

以壳聚糖、丙烯酰胺、甲基丙烯酰氧乙基三甲基氯化铵为原料,硝酸铈铵为引发剂,Span-20为乳化剂,通过反相乳液聚合技术,合成壳聚糖阳离子接枝共聚物。分析讨论了乳化剂用量、引发剂浓度、油水体积比、单体配比、反应时间、反应温度对共聚物接枝率的影响,并采用正交试验方法对合成条件进行了优化。研究了其对重金属离子Cu2 、Cd2 、Zn2 的吸附性能。结果表明,在Cu2 、Cd2 、Zn2 的混合离子体系中,该共聚物对Cu2 、Zn2 有选择性吸附。     

Coaxial electrospinning core-shell fibers for self-healing scratch on coatings

Polystyrene (PS) fibers with core-shell structure were prepared by coaxial electrostatic spinning using liquid epoxy or curing agent as the core and PS solution as the shell. Scratch self-healing coatings were realized by using the healant-loaded core-shell fibers in the matrix.