Amperometric detection of hydrazine by cyclic voltammetry and flow injection analysis using ruthenium modified glassy carbon electrodes

Glassy carbon electrodes modified with (5-amino-1,10-phenanthroline)bis(bipyridine)ruthium(II) chloride hydrate, [(bpy)₂Ru(5-phenNH₂)]Cl₂·H₂O, are shown to oxidize hydrazine with excellent sensitivity. The presence of an amine group on the ruthenium complex facilitates electropolymerization onto the electrode surface. Using cyclic voltammetry, a large catalytic current is observed upon oxidation of hydrazine in phosphate buffer (pH 5.0), compared to the current obtained from the ruthenium-modified electrode with no hydrazine present. The sensitivity of cyclic voltammetry is sufficient for obtaining a linear calibration curve for hydrazine over the range of 10⁻⁵ to 10⁻² M. Hydrodynamic amperometry was used to determine the working potential for flow injection analysis. The limit of detection for hydrazine was determined to be 8.5 μM using FIA. The thickness of these films was shown to increase linearly with the number of electropolymerization cycles, in the range of 1000-2500 nm for 5-20 cycles, respectively, using Rutherford backscattering spectrometry (RBS). RBS analysis also suggests that the film is multilayered with the outermost layers containing a high ruthenium concentration, followed by layers where the concentration of ruthenium decreases linearly and approaches zero at the electrode surface.     

On the selection of the optimal plasticizer for calix[n]arene-based ion-selective electrodes: Possible correlation between the ion selectivity and the ‘softness’ of the plasticizer

A criterion for the selection of a suitable plasticizer for calix[n]arene-based ion-selective electrodes is discussed. The cation selectivity of plasticized membranes without the ligand was first measured as a reference. The membranes can be roughly classified into two groups. The first group shows cation selectivity in the order Cs⁺+>K⁺>Na⁺>Li⁺. The membranes in the second group are made of phosphorus plasticizers, which show a selectivity in the reverse order. The plasticizers in the first group featured a linear relationship between the dipole moment of the plasticizer (calculated by a PM3 method) and the ratio of cesium selectivity to lithium selectivity. The linear relationship supports the view that the polar membrane which includes a soft plasticizer with a large dipole moment shows selectivity for Cs⁺, whereas the nonpolar membrane including the soft plasticizer with the small dipole moment shows much lower selectivity for Cs⁺. Next, 2-fluorphenyl-2-nitrophenyl ether (FPNPE) which showed the highest Cs⁺ selectivity and tris(2-ethylhexyl)phosphate (TEHP) which showed the highest Li⁺ selectivity were mixed in an appropriate ratio to make membranes with a different affinity for hard ions. The metal selectivities of several crown-based and calixarene-based ionophores were examined in these membranes. Although a few exceptions exist, the polar soft membrane is favorable when the interfering metal ion is hard, whereas the hard membrane is favorable when the interfering metal ion is soft.     

Chemical species produced in the reaction between ethanedial (glyoxal) and 5-amino-1,10-phenanthroline and their iron(II) complexes: electrochemical studies and analytical applications

The cyclic voltammetric behavior of carbon paste electrodes modified by direct admixing with the products of the reactions between ethanedial (glyoxal) and 5-amino-1,10-phenanthroline at 100°C and that of their iron(II) complexes is reported. The ligand(s) produced in absence of iron(II) are able to complex iron(II) and copper(II) ions reversibly, but other ions such as nickel(II), cobalt(II), cadmium(II) and manganese(II), if complexed, show no electrochemical activity. Admixing with the products of the reaction in the presence of excess of iron(II) ion, because of high insolubility and fast electron exchange, produces surfaces useful for amperometric detection in continuous-flow systems. The voltammetric and amperometric behavior in the presence of HSO^?₃ ions is reported in order to illustrate this application.     

Amperometric detection of nitrite and nitrate at tetraruthenated porphyrin-modified electrodes in a continuous-flow assembly

The modification of a glassy carbon surface by coating with an electrostatically assembled film of tetraruthenated cobalt porphyrin/(meso-tetra(4-sulphonatephenyl)porphyrinate zinc(II) yields an indicator electrode that allows the determination of nitrite to be performed with a limit of detection of 0.1 μM in a flow injection configuration. The dynamic range extends up to 1000 μM and the repeatability of the measurements was evaluated to be 1.5% with a throughput of 50 samples per hour. The efficiency of the bilayered film to mediate the electron transfer allows the determinations to be performed at a less positive potential (+0.75 V) with enhanced sensitivity. The coating also prevents the surface poisoning and its stability is maintained over several weeks. The same detector was used for determination of nitrate after reduction to nitrite in a reductor column containing copperised cadmium. This method was used for the determination of nitrate and nitrite in mineral water, saliva and cured meats, the results being in agreement with certified values and those obtained by using recommended procedures.     

A Siloxane Homopolymer with Interacting Ferrocenes as a New Material for the Preparation of Sensors Based on the Detection of Hydrogen Peroxide

The electrochemical characterization of a hydrogen peroxide sensor based on a ferrocene‐containing polymer electrochemically deposited onto a platinum electrode is described. The redox polymer consists of a siloxane‐based homopolymer, with pendant electronically communicated ferrocenyl moieties. The electrodes were used as the transducer for glucose and lactate‐sensing enzyme sensors. Amperometric biosensors were prepared by immobilization of glucose oxidase (Gox) or lactate oxidase (Lox) onto these modified electrodes. The steady‐state amperometric response of the sensors is investigated as a function of the applied potential and substrate concentration. Interferences, sensitivity and stability of the sensors were also studied.     

Activity coefficients of electrolytes from the E.M.F. of liquid membrane cells. II - multicharged electrolyte solutions

The activity coefficients of Co(en)₃Cl₃ and K₂SO₄ were measured by means of a cell with ion-exchange liquid membranes following the method described in paper I. The results prove that this method is even more valuable with multicharged salts than with 1-1 electrolytes. The values obtained are precise and reliable down to dilution limits never before accessible, e.g., 4×10^–5 mol-kg^–1 in Co(en)₃Cl₃. High dilution levels are of particular importance when dealing with highly charged electrolytes since the trend at higher concentrations often leads to errors both in extrapolation to infinite dilution and in the absolute activity coefficients. As an application, the activity coefficients of [Co(en)₃]₂(SO₄)₃-suspected to be wrongly evaluated in past literature-were measured, and their values at low concentrations were actually lower than those quoted before.     

Chemical species produced in the reaction between ethanedial (glyoxal) and 5-amino-1,10-phenanthroline and their iron(II) complexes: preparation and some spectrometric studies

Chemical species obtained by reaction of 5-amino-1, 10-phenanthroline with ethanedial (glyoxal) are reported with regard to their preparation, chemical composition and spectrometric characterization (UV-visible, infrared and liquid secondary ion mass spectrometry). Products of the reaction are postulated to be a mixture of species with molecular weights of 339, 371,480 and 524 u. Chemical reactions leading to these products and possible structural formulas for each of these species are presented. The iron complexes of these ligands, because of their extremely low solubility in most solvents, find application as redox mediators when incorporated in carbon paste electrodes, particularly for sensing in continuous-flow systems.     

Potentiometric pH response of membranes prepared with various aminated-poly (vinyl chloride) products

The preparation and potentiometric pH response properties of membranes formulated with various aminated-poly(vinyl chloride) (PVC-NH₂) products are described. Products containing secondary and/or primary amino functional groups are obtained by modifying PVC with mono- and/or diamines, respectively. Blank membranes prepared with either type of aminated-polymer exhibit nearly Nernstian potentiometric pH responses over different pH ranges. In general, membranes based on diamino products exhibit pH response over a wider range (5–10.5) than membranes formulated with monoamino products (<8.0). These potentiometric results are used to estimate the basicity of the various primary and secondary amino sites in the membrane phases.Dedicated to Professer W. Simon on the occasion of his 60th birthday     

Increased electrochemical detector sensitivity by electrode surface modification

Summary Electrode surface modification by electrochemical pretreatment of glassy carbon electrodes was shown to enhance significantly the sensitivity of the electrodes for the detection of timolol and oxprenolol, but reduce slightly the sensitivity to prenalterol. This method may permit the detection of exprenolol and timolol with increased sensitivity, or may allow their detection at lower applied potentials than is presently possible. Electrode surface modification may prove to be a valuable aid to the detection of compounds that are considered to be outside the practical limits of electrochemical detection.     

Sol-gel-derived prussian blue-silicate amperometric glucose biosensor

A new type of inorganic biosensor is introduced. The sensor comprises glucose oxidase enzymes encapsulated in a sol-gel-derived Prussian blue-silicate hybrid network. Glucose is detected by the biocatalytic reduction of oxygen followed by catalytic reduction of hydrogen peroxide by the Prusian blue catalyst. The sol-gel silicate entails a rigid encapsulating matrix, the Prussian blue provides chemical catalysis and charge mediation from the reduction site to the supporting electrode, and the enzyme is responsible for the biocatalysis. The feasibility of a dual optical/electrochemical mode of analysis is also demonstrated.