一种双段多层长周期光纤光栅光谱特性研究

长周期光纤光栅(LPFG)传感器具有非常广泛的应用价值,而有效解决物理量交叉敏感问题是其实用化的关键。基于LPFG对包层外介质折射率和厚度的敏感性,提出一种双段多层折射率横向分布结构的新型LPFG传感器的设计,并利用耦合模理论和传输矩阵方法分析了镀膜材料折射率、膜层厚度和镀层长度对新型LPFG传感器光谱特性的影响。软件仿真结果证明,这种LPFG由于结构设计上的特殊性,将使LPFG的谐振峰发生分裂,即一个透射峰分裂为两个。由于两个分裂峰对应力和温度的灵敏度不同,利用该结构的LPFG作为传感器,可以实现温度、应力等物理量的同步测量,从而解决LPFG传感器的交叉敏感问题。     

时间延迟积分型面阵CMOS图像传感器MTF速度失配模型研究

研究了时间延迟积分型面阵互补金属氧化物半导体(CMOS)图像传感器调制传递函数(MTF)速度失配特性,在分析累加级数、像素尺寸、镜头放大倍数、行周期及电机运动速度失配等影响因素的基础上,建立了MTF速度失配模型。基于现场可编程门阵列(FPGA)开发板,搭建面阵CMOS图像传感器实现线阵时间延时积分(TDI)的CMOS测试系统。实验结果表明,在光强为3lx,速度失配M(ΔV/V)<2,8级时间延迟积分与面阵成像相比,MTF值提高50%;当累加级数为8级,速度失配满足M(ΔV/V)=2的速度失配容限时,奈奎斯特频率处的MTF值下降10%,当速度失配达到M(ΔV/V)=10时,MTF值下降35%。     

Single LED based dual wavelength referenced optical fibre sensor system using intensity modulation

An intensity-modulated optical fibre sensor system is described which employs a single LED source to provide the measurand and the reference signals with two separate wavelength bands. The allocated wavelength bands are selected to minimize any differential intensity effects that may arise from LED thermal variations. The sensor system, comprising a transceiver unit connected to an optical displacement sensor using a single optical fibre, provides an output fully referenced for all major common-mode variations that are likely to occur. Performance characteristics for the prototype system are reported which show a linear displacement range of over 20 mm.     

应用LiNbO_3声表面波驱动的全光纤声光频移器

介绍一种工作在10.7MHz的全光纤声光频移器.它由在LiNbO_3基片上制作的叉指电极换能器产生的声表面波驱动.当驱动电功率1.5W时,频移光转换效率达35％.     

基于电化学与热能的耦合关系演算聚合物锂离子动力电池的温度状态及分布

基于电化学-热耦合模型研究聚合物锂离子动力电池放电过程热行为, 分析了放电倍率、冷却条件对电池放电过程的温度变化及分布的影响规律. 结果表明: 3C放电时, 模型计算结果与实测结果的平均偏差为0.57 K, 方差为0.15, 说明模型准确度较高. 电芯的平均生热率在整个放电过程中呈现出增加的趋势, 初期和末期增长较快. 大倍率放电时, 与电流密度的平方呈正比的不可逆热所占的比重较大, 小倍率放电时, 电化学反应可逆热占主导. 改善冷却条件能降低电池放电过程的平均温度, 对流传热过程的表面传热系数为5 W/(m²·K), 1 C, 3 C, 5 C放电结束时, 电芯的平均温升为分别为6.46 K, 17.67 K, 27.53 K, 当对流传热过程的表面传热系数增加至25 W/(m²·K)时, 温升比自然对流条件下相同倍率放电时的温度分别降低了2.91 K, 4.68 K, 5.62 K, 但电芯温度分布的不一致性也会加剧. 关键词： 电化学 耦合 锂离子动力电池 温度分布     

Application of magneto-optical method for real-time visualization of eddy currents with high spatial resolution for nondestructive testing

In this paper we describe a new, laser supported, eddy current microscope for the real-time visualization of eddy current distributions. In the experimental set-up, the induction of eddy currents is conventionally performed by an alternating current excitation coil above the object surface. The magnetic field induced by the eddy currents is detected by the use of the Faraday effect. For that purpose, a laser beam is passed through a suitable thin crystal integrated in the excitation coil. The polarization direction of the laser beam is rotated in this thin crystal depending on the local magnetic field. The area distribution of the rotation angle is transformed into a grey value picture using an optical set-up, which comprises a conventional microscope, a lighting technique, an analyzator, and a CCD sensor. By choosing a suitable optic, a real-time measurement of the magnetic field with a high spatial resolution can be carried out. In this paper, the basic physics and the design of the new microscope are described. The initial results of experimental investigations concerning the resolution power of magneto-optic eddy current sensors are presented and compared with conventional eddy current sensors.     

基于远程控制的六足搜救机器人系统的设计

针对灾后现场环境的危险性与复杂性,设计了一套搜救机器人系统。在基于仿生学的基础上设计机器人六足式移动平台,以Atmega128型单片机为控制核心,通过步态与动作控制,使之具有强大的越障能力和机体灵活性。整个搜救系统分为机器人系统和控制中心系统两大部分。机器人系统配有完备的传感器模块以及高清摄像头,通过无线传输技术,可在0-1000米范围内实现向控制中心系统上位机的数据与图像传输,并接受上位机控制指令,控制中心根据采集到的信息,可以有效指挥现场搜救人员,大大提高了搜救速度与效率。     

Curvature investigation in tapered fibers and its application to sensing and mode conversion

Non-adiabatic tapered fibers are basic photonic components used in a wide range of applications. Here we investigate a way to increase their utility through the controllable bending of one of their tapered sections. The experiments carried out explain, for the first time, the mechanics of this approach showing how these tapers can be used to build more sensitive sensors. Their use as highly efficient mode converters is also discussed.     

Thermal sensors based on Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript> and (Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript>)<Subscript>70</Subscript>(Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>)<Subscript>30</Subscript> thin films

Thin films of Sb₂Te₃ and (Sb₂Te₃)₇₀(Bi₂Te₃)₃₀ alloy and have been deposited on precleaned glass substrate by thermal evaporation technique in a vacuum of 2?×?10^?6 Torr. The structural study was carried out by X-ray diffractometer, which shows that the films are polycrystalline in nature. The grain size, microstrain and dislocation density were determined. The Seebeck coefficient was determined as the ratio of the potential difference across the films to the temperature difference. The power factor for the (Sb₂Te₃)₇₀ (Bi₂Te₃)₃₀ and (Sb₂Te₃) is found to be 19.602 and 1.066 of the film of thickness 1,500 Å, respectively. The Van der-Pauw technique was used to measure the Hall coefficient at room temperature. The carrier concentration was calculated and the results were discussed.     

快速傅里叶变换与线性调频Z变换联合算法在光纤法布里-珀罗传感器解调中的应用

将快速傅里叶变换(FFT)与线性调频Z变换(CZT)联合变换的方法应用到法布里-珀罗(F-P)腔传感器的解调中,从理论上分析了该方法的解调原理及误差.模拟计算得出,该联合算法解调出的腔长的相对误差达到0.01%,腔长的最大绝对误差小于0.05 μm.在对测量范围为O～3 MPa的F-P腔微机电系统(MEMS)压力传感器进行的解调试验中,该算法可以辨别0.01 MPa的压力,腔长与压力数据的拟合度为0.99316,测量压力与实际压力的标准偏差小于0.005 MPa.实验结果表明,FFT与CZT联合解调的方法可以在较少计算量的基础上达到较高的精度,满足实际需求.