Design and synthesis of Ru(II-bipyridyl-containing conjugated polymers

A series of novel π-conjugated polymers containing ruthenium bipyridine complexes was synthesized by a cross-coupling reaction and characterized. These polymers exhibit absorption maxima around 330–350 nm (π-π*) and 460–500 nm metal-to-ligand charge transfer (MLCT), respectively. They are soluble in common organic solvents, and all polymers can be converted into transparent films. We investigated the influence of different donating and acceptor diethynylarenes of the ultraviolet-visible spectra. The oxidation potential, which was measured by cyclic- and square-wave voltametry, showed a typical Ru^2+/3+ exhibited at 1.25 V versus the saturated calomel electrode. The polymers were further characterized with photoluminescence measurements. When excited at 442 nm ( 11a ), the polymer exhibited an emission peak at 690 nm. This peak was attributed to the MLCT states. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 722–732, 2004     

Multicyclic polyethers derived from 1,1,1‐tris(4‐hydroxyphenyl)ethane and 2,6‐dihalopyridines

Poly(pyridine ether)s were prepared in two ways: the polycondensation of silylated 1,1,1‐tris(4‐hydroxyphenyl)ethane (THPE) with 2,6‐difluoropyridine (method A) and the polycondensation of free THPE with 2,6‐dichloropyridine (method B). With method A, the THPE/difluoropyridine feed ratio was varied from 1.0:1.0 to 1.0:1.6. Cycles, bicycles, and multicycles were the main reaction products, and crosslinking was never observed. When ideal stoichiometry was used exclusively, multicycles free of functional groups were obtained. These multicycles were detectable in matrix‐assisted laser desorption/ionization time‐of‐flight (MALDI‐TOF) mass spectra up to B₃₈C₇₆ with a mass of approximately 32,000 Da. With method B, the reaction conditions were varied at a fixed feed ratio to achieve an optimum for the preparation of multicyclic polyethers, but because of the lower reactivity of 2,6‐dichloropyridine, a quantitative conversion was not achieved. The reaction products were characterized with MALDI‐TOF mass spectrometry, viscosity measurements, and size exclusion chromatography. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5725–5735, 2004     

Polyesterification of aromatic dicarboxylic acids and bisphenols with tosyl chloride/dimethylformamide/pyridine promoted by the improvement of the difficult solubility of the activated diacids with lithium chloride

The solution polyesterification of dicarboxylic acids in pyridine, the activated intermediates of which were difficult to dissolve in tosyl chloride/dimethylformamide/pyridine, was investigated in the presence of lithium chloride. The solubility of the activated dicarboxylic acids was largely improved by the presence of the salt, and the polycondensation with bisphenols was greatly facilitated. The salt was more effectively added to a pyridine solution of dicarboxylic acids than to the activated dicarboxylic acids in pyridine. The favorable additive effect on the improved solubility was attributed to a lowered degree of association of the activated dicarboxylic acids, which led to distributions of the resulting oligomers from bisphenols at an earlier stage closer to the theoretical ones and yielded better polycondensation results. The reaction, which proceeded through favorable distributions of the co‐oligomers, produced copolymers of higher inherent viscosities and slightly block sequence distributions determined by NMR. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2725–2733, 2004     

功能性丙烯酸/MBAM体系共聚产物的研制

以丙烯酸和MBAM为主要原料，经聚合，合成了一种高性能的具有良好保水性能的聚合产物，其保水量达到750～1000倍．50℃以下有良好的保水性能，28℃以下有极好的保水性能，并研究了工艺条件对该产品性能的影响因素．     

Axisymmetric Collision Problem for Two Identical Elastic Solids of Revolution

A direct central collision of two identical bodies of revolution is studied. A nonstationary mixed boundary-value problem with an unknown moving boundary is formulated. Its solution is represented by a series in term of Bessel functions. An infinite system of Volterra equations of the second kind for the unknown expansion coefficients is derived by satisfying the boundary conditions. The basic characteristics of the collision process are determined depending on the curvature of the frontal surface of the bodies     

Temperature‐modulated differential scanning calorimetry studies on the origin of double melting peaks in isothermally melt‐crystallized poly(L‐lactic acid)

In this work, the melting behaviors of nonisothermally and isothermally melt‐crystallized poly(L ‐lactic acid) (PLLA) from the melt were investigated with differential scanning calorimetry (DSC) and temperature‐modulated differential scanning calorimetry (TMDSC). The isothermal melt crystallizations of PLLA at a temperature in the range of 100–110 °C for 120 min or at 110 °C for a time in the range of 10–180 min appeared to exhibit double melting peaks in the DSC heating curves of 10 °C/min. TMDSC analysis revealed that the melting–recrystallization mechanism dominated the formation of the double melting peaks in PLLA samples following melt crystallizations at 110 °C for a shorter time (≤30 min) or at a lower temperature (100, 103, or 105 °C) for 120 min, whereas the double lamellar thickness model dominated the formation of the double melting peaks in those PLLA samples crystallized at a higher temperature (108 or 110 °C) for 120 min or at 110 °C for a longer time (≥45 min). © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 466–474, 2007     

Notes on Sublattice-Lattices

We prove that directly reducible lattices and selfdual subdirectly irreducible lattices of locally finite length are determined by their sublattice-lattices. As a corollary we obtain that splitting varieties are closed under the isomorphism of sublattice-lattices iff they are selfdual. A class of selfdual non-closed varieties is given too.     

Influence of preparation methods on structure and properties of PA6/PA66 blends: A comparison of melt‐mixing and in situ blending

The blends composed of polyamide 6 (PA6) and polyamide 66 (PA66) were obtained using two different preparation methods, one of which was the melt‐mixing through a twin‐screw extruder and the subsequent injection molding; and the other, the in situ blending through anionic polymerization of ε‐caprolactam in the presence of PA66. For the former, there existed a remarkable improvement in toughness but a drastic drop in strength and modulus; however, for the latter, a reverse but less significant trend of mechanical properties change appeared. Various characterizations were conducted, including the analyses of crystalline morphology, crystallographic form, and crystallization and melting behaviors using polarized optical microscopy (POM), wide‐angle X‐ray diffraction (WAXD), and differential scanning calorimetry (DSC), respectively; observation of morphology of fractured surface with scanning electron microscope (SEM); measurement of glass transition through dynamic mechanical analysis (DMA); and the intermolecular interaction as well as the interchange reaction between the two components by Fourier transform infrared spectrometry (FT‐IR) and ¹³C solution NMR. The presence and absence of interchange reaction was verified for the in situ and melt‐mixed blends, respectively. It is believed that the transreaction resulted in a drop in glass transition temperature (T_g) for the in situ blends, contrary to an increase of T_g with increasing PA66 content for the melt‐mixed ones. And the two kinds of fabrication methods led to significant differences in the crystallographic form, spherulite size and crystalline content and perfection as well. Accordingly, it is attempted to explain the reasons for the opposite trends of changes in the mechanical properties for these two blends. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1176–1186, 2007     

Trefftz,collocation, and other boundary methods—A comparison

In this article we survey the Trefftz method (TM), the collocation method (CM), and the collocation Trefftz method (CTM). We also review the coupling techniques for the interzonal conditions, which include the indirect Trefftz method, the original Trefftz method, the penalty plus hybrid Trefftz method, and the direct Trefftz method. Other boundary methods are also briefly described. Key issues in these algorithms, including the error analysis, are addressed. New numerical results are reported. Comparisons among TMs and other numerical methods are made. It is concluded that the CTM is the simplest algorithm and provides the most accurate solution with the best numerical stability. © 2006 Wiley Periodicals, Inc. Numer Methods Partial Differential Eq, 2007     

Electrochemical reduction of sodium metavanadate in an equimolar KCl-NaCl melt

Electrochemical reduction of sodium metavanadate in an equimolar KCl-NaCl melt and the effect of acid-base properties of environment on this process are studied by a voltammetry method on a stationary platinum electrode. It is established that the limiting current of the NaVO₃ electroreduction process has a kinetic nature. The process proceeds via an autoinhibition scheme and its rate is limited by an acid-base reaction conjugated with an irreversible charge transfer reaction. A substantial role of cationic composition of the melt is revealed experimentally. Following acidification of the KCl-NaCl-NaVO₃ melt by Mg²⁺ (from MgCl₂), the process passes from an irreversible kinetic regime into a reversible diffusion (quasi-diffusion) process. Values of stability constants for vanadates produced with the aid of acid-base titration of vanadium pentoxide by oxygen ions in experimental conditions are presented. These values are taken into account when calculating kinetic parameters of the NaVO₃ electroreduction.