Solid-state interactions and drug release of teicoplanin in binary combinations with peracetylated α-, β-, and γ-cyclodextrins

Triacetyl α-cyclodextrin, triacetyl β-cyclodextrin and triacetyl γ-cyclodextrin were tested as possible hydrophobic carriers to prolong the release of hydrophilic teicoplanin (TCP). Physical–chemical characterization of individual components, drug-carrier physical mixtures at 0.5, 0.67 and 0.75 mass fraction of carrier, and the respective interaction products by kneading or evaporative crystallization under microwave irradiation was carried out using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). In vitro drug release in pH 7.4 phosphate buffer at 37 °C was determined by intrinsic dissolution rate (IDR) measurements on non disintegrating compressed discs. Solid-state interactions of TCP with triacetyl α-cyclodextrin by evaporative crystallization and kneading and with triacetyl β-cyclodextrin by evaporative crystallization (probably resulting in carrier amorphization) were demonstrated. The role of carrier hydrophobicity, carrier mass fraction and preparation method of solid drug-carrier combinations on solid-state drug-carrier interactions and slowing down of TCP release was assessed. Modulation of drug release can be achieved using TCP-triacetyl γ-cyclodextrin combinations at 0.5 mass fraction of carrier.     

镀铜铁屑-H_2O_2催化氧化降解含酚废水

采用镀铜铁屑代替传统Fenton体系中的FeSO4作为催化剂,通过改变H2O2与镀铜铁屑的投加量、溶液的pH值、反应温度、反应时间等条件,研究了该体系对处理苯酚废水的影响。结果表明,常温下处理实际含酚印染废水,在pH值为4~6,30%H2O2 12mL/L,镀铜铁屑5g/L,反应时间为45min时,COD去除率可达96%,其CODCr从5827mg/L降至419mg/L,色度从2000降至30,符合国家三级排放标准。     

Thermal Stability Of Folic Acid in the solid-state

This study attempts to identify the degradative process which folic acid undergoes in the solid-state under thermal stress. In order to facilitate the process, the various pieces of the chemical structure, namely, p-amino benzoic acid, pterin and glutamic acid as both its d- and l-isomers were investigated as separate entities. These structured solid-state pieces were then compared to the composite solid state folic acid degradative curves in order to identify the peaks seen and provide direction for the interpolation of the degradative mechanism. It was observed that none of the structural pieces could be superimposed as assumed earlier and hence an attempt was made to identify the decomposition products using various analytical techniques such as infrared spectroscopy, mass spectroscopy and X-ray diffraction which suggested that the glutamic acid fragment is lost first as evidenced by acid loss and amide enhancement in the IR spectra. The vitamin was ultimately degrading to carbon fragments and that further identification was not necessary. This revised version was published online in August 2006 with corrections to the Cover Date.     

Properties of ITO films prepared by reactive magnetron sputtering

Indium tin oxide (ITO) thin films were deposited by mid frequency pulsed dual magnetron sputtering using a metallic alloy target with 10 wt.% tin in an atmosphere of argon and oxygen. The aim of the work was to study the interdependence of structural, electrical and optical properties of ITO films deposited in the reactive and transition target mode, respectively. The deposition rate in the transition mode exceeds the deposition rate in the reactive mode by a factor of six, a maximum value of 100 nm·m min⁻¹ could be achieved. This corresponds to a static deposition rate of 200 nm min⁻¹. The lowest electrical resistivity of 1.1·10⁻³ Ω cm was measured at samples deposited in the high oxygen flow range in the transition mode. The samples show a good transparency in the visible range corresponding to extinction coefficients being below 10⁻². X-ray diffraction was used to characterise crystalline structure as well as film stress. ITO films prepared in the transition mode show a slightly preferred orientation in (211) direction, whereas films deposited in the reactive mode are strongly (222) oriented. Compared to undoped In₂O₃ all samples have an enlarged lattice. The lattice strain perpendicular to the surface is about 0.8% and 2.0% for films grown in the transition and the reactive mode, respectively. Deposition in the transition mode introduces a biaxial film stress in the range of −300 MPa, while stress in reactive mode samples is −1500 MPa.     

甲醇催化分解动力学之研究

甲醇的裂解产物为H_2与CO,故甲醇被视为一种方便、安全的贮氢材料,可作为汽油的代用燃料;其裂解气作为保护气氛可广泛应用于热处理工业。甲醇裂解有两种方法,高温热裂解(约930℃)与低温催化裂解(约300℃)由于低温催化裂解有诸多优点,在工业上的应用正在发展。     

The crystallization characteristics of polypropylene and low ethylene content polypropylene copolymer with copolyesters

The crystallization characteristics of polypropylene (PP) and low ethylene content PP copolymers with and without nucleating agents were studied by differential scanning calorimetry (DSC). PP and PP copolymers was blended with three different kinds of co[poly(butylene terephthalate-p-oxybenzoate)] copolyesters, designated B28, B46, and B64, with the copolyester level varying from 5 to 15 wt.%. All samples were prepared by solution blending in hot xylene solvent at 50 °C. The crystallization behavior of samples was then studied by DSC. The results indicate that these three copolyesters accelerate the crystallization rate of PP and PP copolymers in a manner similar to that of a nucleating agent. The acceleration of crystallization rate was most pronounced in these blend systems with a maximum level at 5 wt.% of B28. The observed changes in crystallization behavior are explained by the effect of the composition and the amount of copolyester in the blends.     

Sorption properties of freshly precipitated alumogels

The influence of the pH of precipitation and the ionic medium nature on the composition, surface charge, and kinetic sorption characteristics of aluminum oxyhydroxides formed by alkaline hydrolysis of an aqueous solution of aluminum nitrate was studied. The methods of drop titration with alkali, argentometric titration, point of zero charge, and indicator reactions of heterogeneous hydrolysis were used. The composition of the freshly precipitated hydrogels of aluminum(iii) oxyhydroxide, rate constants of heterogeneous hydrolysis of the IrCl₆ ^2– ions as indicator reactions, and the pH of the point of zero charge were determined. The rate of indicator reactions (as for other oxyhydroxide hydrogels) depends strongly on the pH of precipitation. However, it is lower than the rates characteristics of iron(iii) and chromium(iii) oxyhydroxides obtained under similar conditions. The pH of the point of zero charge for the alumogels in a chloride medium is 8.3 and that in a sulfate medium is 9.5.     

Comparison of the thermal behavior of three cellulose fibers mercerized or submitted to solar degradation

Comparison of Lyocell, modal and viscose fibers was performed by means of differential scanning calorimetry, thermogravimetry and scanning electron microscopy. Thermal analysis was performed in air atmosphere. Samples were mercerized (21.3 g 100 mL-1) or submitted to solar radiation (seven months). Solar degraded samples presents a higher thermal stability and are initially less degraded. Furthermore, Lyocell fiber is the most stable under thermal degradation conditions. Heating produces a reduction of the fiber diameter (about 50%). This revised version was published online in July 2006 with corrections to the Cover Date.     

SYNTHESIS AND PHOTOCHROMISM OF ACRYLIC ESTER COPOLYMERS BEARING PENDANT VIOLOGEN GROUPS

A series of acrylic ester copolymers with viologen group as pendant were synthesizedthrough the reaction of MMA-EBA (Ethenyl bromoacetate) copolymer with 4-(4'-pyridyl)-N-alkyl (or arylalkyl) pyridiniums. These viologen copolymers can exchange their anionwith NH_4PF_6 in methanol to improve their solubility in organic solvents such as DMFand acetone. Compared with the corresponding low molecular viologens, these viologencopolymers have relatively lower color development rate under UV light and fade fasterin air due to less affinity to photo-reductant and deficiency of association between theircation radicals. Their photofatigue resistant ability is also slightly better than that of lowmolecular vinlogens.     

Thermal degradation behaviors of some branched and linear polysiloxanes

The thermal degradation behaviors of some branched and linear polysiloxanes were studied by thermogravimetric (TG) analysis and infrared (IR) spectroscopy, and the effect of phenyl content on the thermal stability of the tested branched polysiloxanes was investigated. The branched polysiloxanes with phenyl obtain higher thermal stability at lower temperature. The degradation residues of the examined branched polysiloxanes at 800 °C are rather high, 65.1-77.6% in N₂ and 40.5-66.5% in air, respectively. However, the amount of solid residue increases with decrease in phenyl content in both N₂ and air atmospheres. It was found that the thermal stability of the branched polysiloxanes is higher than that of the linear one, which indicated that the branched structure benefits the formation of a crosslink in the solid residue.