Wavelength effect on the photoinduced reaction of polymethylmethacrylate

Polymethylmethacrylate (PMMA) containing benzophenone (BP) was photo-irradiated with monochromatic radiation of wavelength 260–360 nm using the Okazaki Large Spec-trograph (OLS). On irradiation of PMMA films containing BP in air, the sensitized main-chain scission and photocrosslinking of PMMA took place simultaneously. These reactions are dependent on irradiation wavelength. The threshold wavelength for both reactions is found to be ca. 380 nm. The number of main-chain scission and amount of gel increased with the increase of BP concentration in PMMA. Photosensitized main-chain scission favors the irradiation of radiation at ca. 280 nm and photocrosslinking takes place efficiently with the exposure of 340 nm radiation. A possible mechanism for photosensitized reaction is proposed. © 1995 John Wiley & Sons, Inc.     

A study on the influence of anionic surfactants on electrochemical degradation of polyaniline

The influence of anionic surfactants on the electrochemical degradation of polyaniline (PANI), deposited by electro-polymerization onto platinum electrodes, was investigated in an aqueous medium by means of cyclic voltammetry. The degradation rate was found to be greatly dependent on the pH of the solution. The electrochemical degradation of PANI/dodecylsulfate and PANI/dodecylbenzenesulfonate films was compared with that of a PANI/hydrochloride film. The degradation rate in the two former cases decreased by some 50% compared to the PANI/hydrochloride film in aqueous solution at pH = 2. The results were confirmed with theoretical calculations performed on the evaluation of head group charge of surfactants, the distance of anions from PANI positive sites and the shielding of anions on PANI positive sites.     

Exhaustive degradation of the ring D of 3,20-epoxy ent-kaurane-type diterpene maoecrystal A

This study described a new approach for exhaustive degradation of the ring D of maoecrystal A (1), an ent-kaurane-type diterpene from Isodon eriocalyx, in seven steps mainly involving retro-aldol reaction, epoxylation, NaIO₄ oxidation, and Baeyer-Villiger process in a 19% overall yield.     

活性炭纤维电极电解法处理墨绿B染料废水

将铁丝缠绕在活性炭纤维(简称ACF)上制成电极,并在阴极鼓入空气,用电解生成的Fenton试剂处理墨绿B染料模拟废水.研究了电压、pH值、温度、空气流量、支持电解质的浓度等因素对染料脱色率的影响.结果表明,pH值越低,温度越高,处理效果越好,气流量的改变对于处理效果影响不大.室温时处理浓度为50mg·L-1的活性染料墨绿B,在实验电压为11V,中性条件下,无水硫酸钠的浓度为20g·L-1,通入空气流量为60L·min-1时,处理60min,色度去除率达到95%左右.55℃时,电解30min色度去除率就达到96%,60min时达到100%.     

Thermal Degradation of Polychloroprene Rubber Under Isothermal and Non-Isothermal Conditions

The results of a kinetic investigation of the non-isothermal degradation and the isothermal degradation of the residual deformation under constant deflection for polychloroprene rubber are presented. A relationship was derived between the degree of non-isothermal conversion and the value of the investigated mechanical property. This revised version was published online in July 2006 with corrections to the Cover Date.     

聚苯基不对称三嗪的热分解

用高分辨裂解气相色谱－质谱（ＨＲＰｙＧＣ－ＭＳ）考察了由对苯二眯腙和四种不同芳香族四酮合成的聚苯基不对称三嗪的热分解行为，鉴定了相应裂解产物的组成、分布及其与高分子结构的关系，并用热重法（ＴＧ）测定了它们的热分解反应动力学参数，提出了其热分解反应机理．     

Efficiency of radiation-induced main-chain scission of poly (methyl methacrylate) depends on the irradiation temperature because of coexisting monomer

Effect of irradiation temperature on the main-chain scission of poly (methyl methacrylate) (PMMA) caused by γ-irradiation was studied by means of gel permeation chromatography and ESR spectroscopy. Although no temperature dependency was observed on the scission efficiency for purified PMMA, the efficiency for crude or monomer-doped purified PMMA was decreased by decreasing the temperature below ca. 200 K. Above 200 K the efficiency was constant and did not depend on the purity of PMMA. ESR study of the irradiated PMMA revealed that the suppression of the scission below 200 K is induced by the addition of methyl methacrylate monomer to primary radical species, which otherwise cause the main-chain scission by warming the polymer above 200 K. The primary radical generated above 200 K immediately converts to the scission-type ? CH₂ ? ?(CH₃) COOCH₃ radical through the β-scission of the polymer main chain, so that the efficiency of the scission does not depend on both the impurity and the irradiation temperature. © 1994 John Wiley & Sons, Inc.     

Acid Pullulanase from Bacillus polymyxa MIR-23

Within the frame of a screening program aimed at the isolation of amylolytic sporeformers, one strain with high amylolytic activity designated MIR-23 was selected. The microbial characterization was carried out by morphological and biochemical tests and, by means of statistical treatment, was identified asBacillus polymyxa. The organism could grow in acidic conditions (pH 5.0) on a starch medium and produce α-amylase, pullulanase, and α-glucosidase. Batch cultures showed the highest enzyme activities in the stationary phase. Pullulanase activity exhibited an optimal temperature of 52–57°C at pH 4.5–5.5. These properties would allow its use in the saccharification processes in the starch industries.     

A preliminary study on fabrication of nanoscale fibrous chitosan membranes in situ by biospecific degradation

A new approach for in situ fabrication of nanoscale fibrous chitosan membrane by biospecific degradation under physiological situation was studied. The chitosan binary blend membranes were fabricated by solvent casting of chitosan solution containing highly deacetylated chitosan (HDC) and moderately deacetylated chitosan (MDC) with different ratio. The biodegradation process was performed in PBS (pH 7.4) containing lysozyme at the temperature of 37 °C. Experimental results from weight loss, reducing sugar in surrounding media, FT-IR, X-ray diffraction, gel permeation chromatography (GPC) and SEM throughout the study showed that the biospecific degradation by lysozyme had removed MDC component selectively. When the ratio of MDC in the binary blend membranes amounted to 0.5, nanoscale domains of HDC and MDC were obtained, and thus a nanoscale fibrous structure was fabricated after biospecific degradation of MDC. This nanofibrous structure and the biospecific degradation of chitosan membranes can have potential advantages and interesting implications in tissue engineering and drug delivery.     

Immobilization of cellulase using polyurethane foam

Cellulase was covalently immobilized using a hydrophilic polyurethane foam (Hypol®FHP 2002). Compared to the free enzyme, immobilized cellulase showed a dramatic decrease (7.5-fold) in the Michaelis constant for carboxymethylcellulose. The immobilized enzyme also had a broader and more basic pH optimum (pH 5.5–6.0), a greater stability under heat-denaturing or liquid nitrogen-freezing conditions, and was relatively more efficient in utilizing insoluble cellulose substrates. High molecular weight compounds (Blue Dextran) could move throughout the foam matrix, indicating permeability to insoluble celluloses; activity could be further improved 2.4-fold after powdering, foams under liquid nitrogen. The improved kinetic and stability features of the immobilized cellulase combined with advantageous properties of the polyurethane foam (resistance to enzymatic degradation, plasticity of shape and size) suggest that this mechanism of cellulase immobilization has high potential for application in the industrial degradation of celluloses.