混合稀土对ZL108铝合金组织与性能的影响

对稀土处理前后的ZL108合金进行了机械性能测试和断口分析, 表明稀土处理有利于提高合金的塑性和强度. 对稀土处理前后合金中氢总量进行了分析, 未加稀土的合金内氢总量与稀土处理后的合金相当, 结合性能与断口形态, 从侧面表明稀土改变了氢的存在形式.     

Iron-Cobalt-Silica Aerogel Nanocomposite Materials

Iron-Cobalt-Silica nanocomposites were prepared in form of aerogels. X-ray diffraction, transmission electron microscopy and N₂ physisorption at 77 K were used to investigate the structure, size and dispersion of the nanocrystals and the porous structure in the aerogels and in the final composites. The variation of the supercritical drying conditions gives rise to differences in the morphological features of the aerogels. These differences influence the size of the cobalt oxide nanoparticles in the aerogels. On the other hand, after the reduction treatment the average size of the alloy nanoparticles is the same in all the aerogel nanocomposites. The effect of reduction temperature on alloy formation and particle size is also discussed.     

Spectrophotometric determination of zinc in copper-base alloys with TAN

TAN reacts with zinc(II) forming a red complex with composition 1:2 Zn(II)-TAN and absorption maximum at 582 nm. Zinc can be determined with this reagent in the presence of Triton X-100, in the pH range 6.20-8.00 with a molar absorptivity of 4.5×10⁴ l/mol/cm Beer's Law was obeyed up to least 1.55 g/ml. Copper interference was eliminated with a mixture of thiosulfate and ascorbic acid and nickel separated by precipitation with dimethylglyoxime. The proposed method was used for zinc determination in several copper-base alloys and the results of analysis in comparison with certified values indicated that the procedure was accurate and precise. A derivative procedure is also proposed, allowing zinc determination with high sensitivity (5-400 ng/ml).     

Magnetic susceptibility of liquid gold-indium-zinc alloys

Summary Alloys of the ternary system gold-indium-zinc with a variable content of goldx _Au at a constant ratio ofx _In:x _Zn=1:1 have been investigated by susceptibility measurements from 300 K up to 1500 K with emphasis on the liquid state. The magnetic susceptibilities of the homogeneous liquids were found to vary in a non-linear manner with temperature and composition. At temperatures close to the liquid-solid transition, the susceptibilities pass through a characteristic minimum which tends to disappear with increasing temperature. The anomaly located atx _Au 0.6 seems to be related to a particular valence electron concentration ofe/a 1.6.

---

Magnetische Suszeptibilität von flüssigen Gold-Indium-Zink-Legierungen

Zusammenfassung Legierungen des ternären Systems Gold-Indium-Zink mit einem variablen Goldgehaltx _Au bei konstantem Indium-Zink-Verhältnis (x _In:x _Zn=1:1) wurden zwischen 300 und 1500 K auf ihre magnetische Suszeptibilität untersucht. Das Hauptaugenmerk wurde dabei auf den flüssigen Zustand gelegt. Die magnetischen Suszeptibilitäten der homogenen Schmelzen variieren nichtlinear mit Temperatur und Zusammensetzung. Bei Temperaturen nahe dem übergang flüssig-fest tritt ein charakteristisches Minimum der Suszeptibilität auf, das mit steigender Temperatur verschwindet. Die Anomalie bei einemx _Au vonca. 0.6 scheint mit einer speziellen Valenzelektronenkonzentration (e/a) von etwa 1.6 verknüpft zu sein.

     

温度对贮氢合金MlNi3.75Co0.65Mn0.4Al0.2动力学性能的影响

在-20℃～85℃的范围内系统地研究了温度对贮氢合金MINi3.75Co0.65Mn0.4Al0.2动力学性能的影响.结果表明:该贮氢合金电极的电化学反应电阻Rt,欧姆内阻Ro,阴极极化过电位,阳极极化过电位,阳极极化过程中的电化学反应过电位ηa和浓差极化过电位ηa均随温度的升高而减小,该电极的交换电流密度i0,对称因子β和电极中氢的扩散系数D随温度的升高而增大.当放电电流密度较低时,电化学反应是整个电极过程的速度控制步骤;当放电电流密度较高时,氢的扩散是整个电极过程的速度控制步骤;在中等放电电流密度下,电极过程由电化学过程和氢的扩散过程混合控制.该电极中电化学反应过程和氢扩散过程的活化能分别为28.1 kJ·mol-1和19.9 kJ·mol-1.     

往复挤压准晶增强快速凝固Mg92.5Zn6.4Y1.1合金

采用往复挤压工艺将快速凝固Mg92.5Zn6.4Y1.1合金薄带在330℃挤压2道次和4道次,然后正挤压制成Φ10 mm的棒材。用OM,TEM,XRD及DTA研究了往复挤压过程中准晶相I-Mg3YZn6弥散析出及对力学性能的影响。研究表明,往复挤压有利于快速凝固Mg92.5Zn6.4Y1.1合金薄带的焊合,获得组织致密、均匀、高强韧合金。往复挤压2道次,相组成为-αMg和准晶I-Mg3YZn6,脱溶析出纳米准晶相较少;4道次相组成为-αMg和准晶I-Mg3YZn6及MgZn相,脱溶弥散析出的纳米I-Mg3YZn6准晶相及MgZn相较多。往复挤压提高材料的拉伸性能,其主要原因是细晶强化和析出强化。     

低钴AB5型稀土系贮氢电极合金的研究

为了进一步降低AB5型混合稀土系贮氢合金的成本,采用Cr,Si,Cu替代Co和调节化学计量比的方法制备低钴AB5型贮氢合金。结果表明:3种取代元素在寿命方面的效果依次为Si>Cr>Cu,在放电容量和活化性能方面依次是Cu>Cr>Si。Cr,Cu,Si只有少量的替代才可能发挥其有利影响;通过非化学计量比的调节,低钴混合稀土系贮氢电极合金的放电容量、活化性能及倍率放电能力都能较好地达到实用要求,但是循环寿命有待提高。     

铜(Ⅱ)-铬天青S-过氧化氢体系催化光度法测定痕量铜

本文研究了在氨水介质中,痕量铜对过氧化氢氧化铬天青S褪色反应的催化作用,建立了一个催化光度法测定痕量铜的新方法。线性范围为0～20ng/mL,检出限为5.59×10~(-11)g/mL,并用于铝合金标准样品,环境标准样品和自来水中痕量铜的测定。     

Differential scanning calorimetry and the advanced solidification processing of metals and alloys

This paper describes some examples of the use of differential scanning calorimetry (DSC) in providing information for advanced solidification processing of metals and alloys. Spray forming, squeeze casting, grain refinement and crystallization of amorphous alloys are all discussed. DSC measurements are shown to be valuable for testing kinetic theories of nucleation and growth, and validating solidification process models.     

Corrosion-stable nickel- and cobalt-based alloys for dental applications

In a comparative study the in vitro corrosion behavior of a selection of nickel- and cobalt-based alloys for application in dentistry containing no noble metals was studied with slow scan cyclic voltammetry. The obtained breakthrough potentials, the repassivation behavior and further typical features of the cyclic voltamograms are correlated with the chemical composition as measured with electron beam microanalysis. Surface inhomogenities detected with the latter method are discussed with respect to the electrochemical behavior. For all alloys stabilities in terms of breakthrough potential superior to previously reported data for nickel-base alloys are found.