4~20 K 温区固体界面导热填料接触热阻实验研究

超导量子干涉仪、 超导光子探测器等深空探测器需要液氦温区制冷技术提供极低温温度, 固体界面接触热阻的存在会增大耦合界面温度差, 进而增加制冷机系统冷损. 为定量探究4~20 K 深低温区固体接触热阻, 采用GM 作为冷源, 设计了一台可同时调节压力和低温温度的固体界面接触热阻测试实验台. 利用感压纸进行接触界面压力校核, 并对温度重复性进行验证. 实验测试了不同导热介质填充情况下, 温度和压力变化时固体接触热阻的变化规律. 基于最小二乘法对实验数据进行半经验公式拟合, 获得4 ~20 K 温区不同压力加载条件下的接触热阻的定量参考.     

单摆周期的系统误差分析

文章逐个分析计算了单摆的摆角、摆球的自转、摆线质量、空气浮力以及空气阻力对于单摆周期的影响,以1 m长5°小幅单摆为例,得到这5种因素带来的系统相对误差分别为+0.45‰、+0.02‰、-0.45‰、+0.07‰、-0.14‰,合计仅为-0.05‰,即这5种误差因素几乎相互抵消,小幅单摆实验在理论上的系统误差极小.文章给出了较为详细的推理、计算和分析过程,尤其空气阻力矩的推理过程以及图、表等,意在提供较为完整和准确的认识.文末,针对人们在空气阻力认识上可能存在的某些不足,文章给出了几点必要的说明.     

A 3D SiC MOSFET with poly-silicon/SiC heterojunction diode

A three-dimensional(3D)silicon-carbide(SiC)trench metal-oxide-semiconductor field-effect transistor(MOSFET)with a heterojunction diode(HJD-TMOS)is proposed and studied in this work.The SiC MOSFET is characterized by an HJD which is partially embedded on one side of the gate.When the device is in the turn-on state,the body parasitic diode can be effectively controlled by the embedded HJD,the switching loss thus decreases for the device.Moreover,a highly-doped P+layer is encircled the gate oxide on the same side as the HJD and under the gate oxide,which is used to lighten the electric field concentration and improve the reliability of gate oxide layer.Physical mechanism for the HJD-TMOS is analyzed.Comparing with the conventional device with the same level of on-resistance,the breakdown voltage of the HJD-TMOS is improved by 23.4%,and the miller charge and the switching loss decrease by 43.2%and 48.6%,respectively.     

Composition dependence of unipolar resistance switching in TaOx thin films

Amorphous TaO_x thin films were deposited at different temperatures, and the resistance switching properties of the Pt/TaO_x/Pt structure were investigated. X‐ray photoelectron spectroscopy showed that the amount of Ta₂O₅ in the film decreased and the content of Ta suboxides increased substantially when the growth temperature was increased. Unipolar resistance switching near the anode was stable only for TaO_x film grown at room temperature. The experimental results revealed the critical effect of the film composition on the resistance switching behavior of TaO_x films. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

A robust numerical model for premixed flames with high density ratios based on new pressure correction and IMEX schemes

In this study we present a model for the interaction of premixed flames with obstacles in a channel flow. Although the flow equations are solved with Direct Numerical Simulation using a low Mach number approximation, the resolution used in the computation is limited (∼1 mm) hence the inner structure of the flame and the chemical scales are not solved. The species equations are substituted with a source term in the energy equation that simulates a one-step global reaction. A level set method is applied to track the position of the flame and its zero level is used to activate the source term in the energy equation only at the flame front. An immersed boundary method reproduces the geometry of the obstacles. The main contribution of the paper is represented by the proposed numerical approach: an IMEX (implicit–explicit) Runge–Kutta scheme is used for the time integration of the energy equation and a new pressure correction algorithm is introduced for the time integration of the momentum equations. The approach presented here allows to calculate flames which produce high density ratios between burnt and unburnt regions. The model is verified by simulating first simple solutions for one- and two-dimensional flames. At last, the experiments performed by Masri and Ibrahim with square and rectangular bodies are calculated.     

双侧进气突扩燃烧室内液雾燃烧的数值模拟

本文采用全双流体模型对部分切向进气管式双侧进气突扩燃烧室内的液雾燃烧过程进行了数值模拟，将液雾群按初始尺寸分组，数值模拟结果表明不同尺寸液雾的蒸发及燃烧过程显著不同，小尺寸的液雾是先蒸发后燃烧，而较大尺寸的液雾则是边蒸发边燃烧．模拟结果还表明，部分切向进气方式有利于在燃烧室的头部产生大面积的中心回流区，该回流区的存在有利于加强混合及火焰稳定．     

Evaluation of surface characteristics under fretting of electrical contacts: Removal behaviour of hot dipped tin coating

The fretting corrosion behaviour of hot dipped tin coating is investigated at low fretting cycles at ±25 μm displacement amplitude, 0.5N normal load, 3 Hz frequency, 45-50% relative humidity, and 25 ± 1 °C temperature. The typical characteristics of the change in contact resistance with fretting cycles are explained. The fretted surface is examined using laser scanning microscope, scanning electron microscope and energy dispersive X-ray analysis to assess the surface profile, extent of fretting damage, extent of oxidation and elemental distribution across the contact zone. The interdependence of extent of wear and oxidation increases the complexity of the fretting corrosion behaviour of tin coating. The variation of contact resistance clearly revealed the fretting of tin coating from 50 to 1200 cycles and the fretting of the substrate above 1200 cycles. The observed low and stable contact resistance region and the fluctuating resistance region at various fretting cycles are explained and substantiated with Scanning electron microscopy (SEM), laser scanning microscope (LSM) and energy dispersive analysis of X-rays (EDAX) analysis results of the fretted surface.     

Synthesis and characterization of Ni1−xCoxFe2O4 nanoparticles

Ni_1−xCo_xFe₂O₄ (x=0.6, 0.8 and 0.9) nanoparticles have been synthesized with various crystallite sizes depending on the thermal treatments and composition (cobalt content) using the sol-gel combustion method. The size of nanoparticles has been controlled by thermal treatment. On the other hand, the magnetic property of the ferrite has been controlled by changing the heat treatment. Morphology and particle sizes of Ni_1−xCo_xFe₂O₄ have been studied using atomic force microscopy (AFM) and transmission electron microscopy (TEM). The presence of functional group has been identified by Fourier Transform Infrared (FTIR) spectra. From TGA-DTA studies, the weight gains of Ni_1−xCo_xFe₂O₄ nanoparticles have been observed and it might be due to capping organic molecules with oxygen at temperatures above 200 °C. Magnetic properties of Ni_1−xCo_xFe₂O₄ particles have been analysed using VSM and it is found that saturation magnetization (M_s) has increased with particle size and has coercivity (H_c) increased initially and then decreased. The M_s and H_c values decreased with the increase of content of cobalt in Ni_1−xCo_xFe₂O₄.     

Ultrasonic irradiation and its application for improving the corrosion resistance of phosphate coatings on aluminum alloys

In this paper, ultrasonic irradiation was utilized for improving the corrosion resistance of phosphate coatings on aluminum alloys. The chemical composition and morphology of the coatings were analyzed by X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM). The effect of ultrasonic irradiation on the corrosion resistance of phosphate coatings was investigated by polarization curves and electrochemical impedance spectroscopy (EIS). Various effects of the addition of Nd₂O₃ in phosphating bath on the performance of the coatings were also investigated. Results show that the composition of phosphate coating were Zn₃(PO₄)₂ · 4H₂O(hopeite) and Zn crystals. The phosphate coatings became denser with fewer microscopic holes by utilizing ultrasonic irradiation treatment. The addition of Nd₂O₃ reduced the crystallinity of the coatings, with the additional result that the crystallites were increasingly nubby and spherical. The corrosion resistance of the coatings was also significantly improved by ultrasonic irradiation treatment; both the anodic and cathodic processes of corrosion taking place on the aluminum alloy substrate were suppressed consequently. In addition, the electrochemical impedance of the coatings was also increased by utilizing ultrasonic irradiation treatment compared with traditional treatment.     

Negative differential resistance behaviour in N-doped crossed graphene nanoribbons

By using first-principles calculations and nonequilibrium Green’s function technique, we study elastic transport properties of crossed graphene nanoribbons. The results show that the electronic transport properties of molecular junctions can be modulated by doped atoms. Negative differential resistance (NDR) behaviour can be observed in a certain bias region, when crossed graphene nanoribbons are doped with nitrogen atoms at the shoulder, but it cannot be observed for pristine crossed graphene nanoribbons at low biases. A mechanism for the negative differential resistance behaviour is suggested.