Synthesis of Cationic PEM Emulsion and Application in Waste Water Treatment

Cationic polymer as a kind of flocculant is widely applied in purification treatment of waste water. Because it has positive charge group, it is able to connect strongly the suspended matters, short cellulose and other microparticles. The research on synthesis of cationic polymer and application in treatment of waste water is very universal abroad. But domestic research on those is not general. The technology of synthesis of PEM is simple, and the production cost is low. It is easy to apply in treatment of waste water.Synthesis of PEM Emulsion FlocculantSome distilled water, PVA(poly(vinyl alcohol)), EA(ethyl acrylate), and K2S2O8(potassium persulfate) were put into reaction vessel. Kept stirring up under nitrogen. When heated the solution to 40℃, dropped the water solution of MTA[(2-methacryloxylethyl)trimethyl ammonium].Maintained the temperature at 70℃, reacted about 7-8 hours. Then got the PEM emulsion. Changed the ratio of EA and MTA. Obtained a series of PEM emulsions.Stability and Convertibility of PEM EmulsionThe test results showed that when the EA/MTA was 85/15, the PEM emulsion was most stable.When the total monomer quantity was 35%, the convertibility of PEM emulsion was the highest,i.e.98.6%.The MTA Copolymerization Ratio and Morphology of PEM EmulsionWhen the monomers EA/MTA=85/15 and total monomer quantity was 35%, the MTA copolymerization ratio of PEM emulsion was 95.15%(the highest), and the PEM emulsion was some microspheres with 100-180nm of diameter.The Test Results of PEM Emulsion in Treatment of Waste Water The PEM emulsion flocculant was applied in treatment of waste water of paper mill, and measured the precipitation time(t) and transmittancy(T). The test results were showed in table 1. The optimum value of PEM which was able to make the waste water of paper mill into clear water was 0.008%.     

Hybrid free radical/cationic frontal photopolymerizations

The irradiation of hybrid photopolymer systems consisting of a free radically polymerizable multifunctional acrylate monomer and a cationically polymerizable epoxide or oxetane monomer was conducted under conditions where only the free radical polymerization takes place. This results in the formation of a free‐standing polyacrylate network film containing quiescent oxonium ions along with the unreacted cyclic ether monomer. The subsequent application of a point source of heat to the film ignites a cationic ring‐opening frontal polymerization that emanates from that site and propagates to all portions of the irradiated sample. This article examines the impact of various molecular structural and experimental parameters on these novel hybrid frontal polymerizations that produce interpenetrating network polymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4331–4340, 2007     

Curcumin: A naturally occurring long‐wavelength photosensitizer for diaryliodonium salts

Curcumin, a naturally occurring, intensely yellow dye extracted from the spice turmeric, is an efficient photosensitizer for diaryliodonium salt photoinitiators at wavelengths ranging from 340 to 535 nm. With curcumin as a photosensitizer, it is possible to carry out the cationic photopolymerization of a wide variety of epoxide, oxetane, and vinyl monomers with long‐wavelength UV and visible light. An example of the photopolymerization of an epoxide monomer with ambient solar irradiation is provided. Several other curcumin analogues were synthesized, and their use as photosensitizers is examined. With such photosensitizers, the range of spectral sensitivity can be extended well into the visible region of the electromagnetic spectrum. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5217–5231, 2005     

Control of the block copolymer morphology in templated epoxy thermosets

It has been found that by the addition of low concentrations of an amphiphilic block copolymer to an epoxy resin, novel disordered morphologies can be formed and preserved through curing. This article will focus on characterizing the influence of the block copolymer and casting solvent on the templated morphology achieved in the thermoset sample. The ultimate goal of this work is to determine the parameters that would control the microphase morphology produced. Epoxy resins blended with a series of amphiphilic block copolymers based on hydrogenated polyisoprene (polyethylene-alt-propylene or PEP) and polyethylene oxide (PEO), specifically, were investigated. In this article, the cure-induced order–order phase transition from the spherical to wormlike micelle morphology will also be discussed. It is proposed that the formation of the wormlike micelle structure from the spherical micelle structure is similar to the phase transition behavior that occurs in dilute block copolymer solutions as a function of the influence of the solvent on micelle morphology. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3338–3348, 2007     

Photoinitiated curing of mono‐ and bifunctional epoxides by combination of active chain end and activated monomer cationic polymerization methods

Photoinitiated cationic polymerization of mono‐ and bifunctional epoxy monomers, namely cyclohexeneoxide (CHO), 4‐epoxycyclohexylmethyl‐3′,4′‐epoxycyclohexanecarboxylate (EEC), respectively by using sulphonium salts in the presence of hydroxylbutyl vinyl ether (HBVE) was studied. The real‐time FTIR spectroscopic, gel content determination, and thermal characterization studies revealed that both hydroxyl and vinyl ether functionalities of HBVE take part in the polymerization. During the polymerization, HBVE has the ability to react via both active chain end (ACE) and activated monomer mechanisms through its hydroxyl and vinyl ether functionalities, respectively. Thus, more efficient curing was observed with the addition of HBVE into EEC‐containing formulations. It was also demonstrated that HBVE is effective in facilitating the photoinduced crosslinking of monofunctional epoxy monomer, CHO in the absence of a conventional crosslinker. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4914–4920, 2007     

Physicochemical studies on hydrophobic PEO‐PPO‐PEO triblock copolymer micelles in SDS micellar environment

The shape, size, aggregation, hydration, and correlation times of water insoluble PEO‐PPO‐PEO triblock copolymer micelles with sodium dodecylsulfate (SDS) micelles were investigated using transport studies and dynamic light scattering technique. From the conductance of micellar solutions of the polymer in 25 mM SDS and 5 mM NaCl, the hydration of polymer micelles were determined using the principle of obstruction of electrolyte migration by the polymer. The asymmetry of the micellar particles of polymer and polymer‐SDS mixed micellar systems in 5 mM NaCl and their average axial ratios were calculated using intrinsic viscosity and hydration data obeying Simha–Einstein equation. Hydration number and micellar sizes were variable with temperature. The shape of the polymer micelles has been ellipsoidal rather than spherical. The micellar volume, hydrodynamic radius, radius of gyration, diffusional coefficients as well as translational, rotational and effective correlation times have been calculated from the absolute values of the axes. The partial molal volume of polymer micelles has also been determined and its comparison with the molar volume of pure polymer suggested a volume contraction due to immobilization of the water phase by the hydrophilic head groups of the polymer. The thermodynamic activation parameters for viscous flow favor a more ordered water structure around polymer micelles at higher temperatures. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2410–2420, 2007     

NMR Study of the propagation center in the cationic polymerization of N-benzoyl-8-octanelactam. II. Investigation of the propagation center

The nature of the propagation center in the cationic polymerization of N-benzoyl-8-octanelactam initiated by octanoylium hexachlcroantimonate, SbCl₅, and Ph₃CAsF₆ in perdeuterated tetrachloroethane or its mixture with o-dichlorobenzene was studied using ¹H, ¹³C, ¹⁹F, ³¹P, ⁷⁵As, and ¹²¹Sb nuclear magnetic resonance (NMR) of model oligomers and the products of their end-capping with triphenylphosphine. In all cases, the nature of the propagation center has been found to be of an acylium ion pair with an SbCl₆^? or AsF₆^? counterion coordinated with the nearest benzoylamide group and cosolvated by the solvent. © 1994 John Wiley & Sons, Inc.     

Monitoring photopolymerization reactions with optical pyrometry

This article describes the development of optical pyrometry (OP) as a new analytical technique for the continuous monitoring of the progress of both free‐radical and cationic photopolymerizations. The method is rapid, reproducible, and very easy to implement. A temperature profile of a photopolymerization can be obtained. Preliminary studies have shown that the temperatures of some polymerizing monomers can easily reach temperatures in excess of 250 °C. The effects of the mass and reactivity of the monomer, light intensity, structures, and concentrations of the photoinitiators and monomers as well as the presence or absence of oxygen on various free‐radical and cationic photopolymerizations were examined with this method. Coupling of real‐time infrared spectroscopy with OP provides a convenient method for simultaneously monitoring both the chemical conversion and the temperature of a photopolymerization. This combined technique affords new insights into the effects of temperature‐induced autoacceleration on the course of photopolymerizations. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 579–596, 2003     

Metallo‐supramolecular micelles: Studies by analytical ultracentrifugation and electron microscopy

In aqueous solutions, amphiphilic block copolymers in which a polystyrene (PS) segment is connected to a poly(ethylene oxide) (PEO) block via a bis(2,2′:6′,2″‐ terpyridine ruthenium) complex can form micelles. Such micelles of the protomer type PS₂₀‐[Ru]‐PEO₇₀, according to the preparation procedure representing frozen micelles, were studied by sedimentation velocity and sedimentation equilibrium analysis in an analytical ultracentrifuge and by transmission electron microscopy, with different techniques applied for the sample preparation. The particles obtained were surprisingly multifarious in size. In ultracentrifugation experiments performed at relatively low salt concentrations, the distributions of the sedimentation coefficient s_20,w showed a pronounced peak at 9.6 S and a broad, only partly separated second peak around 14 S. The molar mass of the particles at the peak was around 430,000 g/mol, corresponding to an aggregation number of approximately 85. The average hydrodynamic diameter of the particles in the peak fraction was approximately 13 nm. In electron micrographs of negatively stained samples, spheres of diameters between 10 and 25 nm were the most abundant particles, but larger ones with a wide size range were also visible. The latter particles apparently were composed of smaller ones. The data from both sedimentation analysis and electron microscopy showed that (1) the studied compound formed primary micelles of diameters around 20 nm and (2) the primary micelles had a tendency toward aggregation. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3159–3168, 2003