Synthesis of Cationic PEM Emulsion and Application in Waste Water Treatment

Cationic polymer as a kind of flocculant is widely applied in purification treatment of waste water. Because it has positive charge group, it is able to connect strongly the suspended matters, short cellulose and other microparticles. The research on synthesis of cationic polymer and application in treatment of waste water is very universal abroad. But domestic research on those is not general. The technology of synthesis of PEM is simple, and the production cost is low. It is easy to apply in treatment of waste water.Synthesis of PEM Emulsion FlocculantSome distilled water, PVA(poly(vinyl alcohol)), EA(ethyl acrylate), and K2S2O8(potassium persulfate) were put into reaction vessel. Kept stirring up under nitrogen. When heated the solution to 40℃, dropped the water solution of MTA[(2-methacryloxylethyl)trimethyl ammonium].Maintained the temperature at 70℃, reacted about 7-8 hours. Then got the PEM emulsion. Changed the ratio of EA and MTA. Obtained a series of PEM emulsions.Stability and Convertibility of PEM EmulsionThe test results showed that when the EA/MTA was 85/15, the PEM emulsion was most stable.When the total monomer quantity was 35%, the convertibility of PEM emulsion was the highest,i.e.98.6%.The MTA Copolymerization Ratio and Morphology of PEM EmulsionWhen the monomers EA/MTA=85/15 and total monomer quantity was 35%, the MTA copolymerization ratio of PEM emulsion was 95.15%(the highest), and the PEM emulsion was some microspheres with 100-180nm of diameter.The Test Results of PEM Emulsion in Treatment of Waste Water The PEM emulsion flocculant was applied in treatment of waste water of paper mill, and measured the precipitation time(t) and transmittancy(T). The test results were showed in table 1. The optimum value of PEM which was able to make the waste water of paper mill into clear water was 0.008%.     

Hybrid free radical/cationic frontal photopolymerizations

The irradiation of hybrid photopolymer systems consisting of a free radically polymerizable multifunctional acrylate monomer and a cationically polymerizable epoxide or oxetane monomer was conducted under conditions where only the free radical polymerization takes place. This results in the formation of a free‐standing polyacrylate network film containing quiescent oxonium ions along with the unreacted cyclic ether monomer. The subsequent application of a point source of heat to the film ignites a cationic ring‐opening frontal polymerization that emanates from that site and propagates to all portions of the irradiated sample. This article examines the impact of various molecular structural and experimental parameters on these novel hybrid frontal polymerizations that produce interpenetrating network polymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4331–4340, 2007     

Curcumin: A naturally occurring long‐wavelength photosensitizer for diaryliodonium salts

Curcumin, a naturally occurring, intensely yellow dye extracted from the spice turmeric, is an efficient photosensitizer for diaryliodonium salt photoinitiators at wavelengths ranging from 340 to 535 nm. With curcumin as a photosensitizer, it is possible to carry out the cationic photopolymerization of a wide variety of epoxide, oxetane, and vinyl monomers with long‐wavelength UV and visible light. An example of the photopolymerization of an epoxide monomer with ambient solar irradiation is provided. Several other curcumin analogues were synthesized, and their use as photosensitizers is examined. With such photosensitizers, the range of spectral sensitivity can be extended well into the visible region of the electromagnetic spectrum. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5217–5231, 2005     

Photoinitiated curing of mono‐ and bifunctional epoxides by combination of active chain end and activated monomer cationic polymerization methods

Photoinitiated cationic polymerization of mono‐ and bifunctional epoxy monomers, namely cyclohexeneoxide (CHO), 4‐epoxycyclohexylmethyl‐3′,4′‐epoxycyclohexanecarboxylate (EEC), respectively by using sulphonium salts in the presence of hydroxylbutyl vinyl ether (HBVE) was studied. The real‐time FTIR spectroscopic, gel content determination, and thermal characterization studies revealed that both hydroxyl and vinyl ether functionalities of HBVE take part in the polymerization. During the polymerization, HBVE has the ability to react via both active chain end (ACE) and activated monomer mechanisms through its hydroxyl and vinyl ether functionalities, respectively. Thus, more efficient curing was observed with the addition of HBVE into EEC‐containing formulations. It was also demonstrated that HBVE is effective in facilitating the photoinduced crosslinking of monofunctional epoxy monomer, CHO in the absence of a conventional crosslinker. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4914–4920, 2007     

Radiation‐induced migration of additives in PVC‐based biomedical disposable devices. Part 1. Surface morphology by AFM and SEM/XEDS

Two different types of plasticized poly(vinyl chloride) (PVC) used for biomedical disposable devices—extruded and injection moulded—were studied in the non‐sterilized condition and after 25 and 50 kGy of beta irradiation. The polymer surfaces were analysed by scanning electron microscopy (SEM) equipped with an x‐ray energy‐dispersive spectroscopy (XEDS) and by atomic force microscopy (AFM). The inner surface of two parts of a venous line showed a different morphology according to their original formulation (for extrusion or injection moulding process) and reacted differently on sterilization with beta irradiation. Moulded parts were affected only slightly by the radiation step, whereas the variations were bigger for the extruded parts. In order to gain the best performances for the medical devices studied, the utmost care must be taken in the sterilization step, which should be optimized as well as the other steps of the manufacturing process. Copyright © 2003 John Wiley & Sons, Ltd.     

Current R & D activities at TRCRE in polymer processing by EB

The current status of the R & D activities is presented on electron beam processing of polymers being carried out at TRCRE. Topics included are sterilization of medical products, graft polymers for selective separation or absorbents and curing of liquid prepolymer-monomer systems.     

透镜初级球差的横向剪切干涉条纹研究

利用玻璃平行平板构成简单的横向剪切干涉仪可以观察到单薄透镜形成的准直光束的剪切干涉条纹,由干涉条纹分布求出对应的几何像差和离焦量.用焦距为190 mm的单薄透镜做实验,实验结果与计算机模拟结果符合,说明可以从剪切干涉条纹的分布求出透镜的轴向调整误差和初级球差.     

CRT显示器稳定性实验研究

用屏幕色度计对一台SONY-G520显示器的显色特性进行了测量,研究了其开机稳定性和短、中、长期内的色差及色度偏差。实验结果表明,开机后,显示器的亮度Y和色度x,y分别可在2h,30min和1h达到相对稳定状态,且在达到相对稳定后,在短、中、长期内的平均色差分别为0.0611,0.1469和1.2536CIELAB色差单位;在中期内,Y,x,y,L,a,b的平均偏差分别为0.0663,0.0008,0.0015,0.0695,0.4740和0.1766。通过对显示器稳定性的测量,为在对比度敏感测量和色貌模型、图像质量、图像感知模型评价等研究领域中用显示器进行实验研究奠定了基础。     

Study of the spontaneous formation of organic layers on carbon and metal surfaces from diazonium salts

This study investigates the spontaneous grafting of different para-substituted phenyl groups on carbon and metallic surfaces from diazonium salts solutions. Glassy carbon, nickel, zinc and iron plates were allowed to react with an acetonitrile solution of aryldiazonium tetrafluoroborate salt by simple dipping. The surfaces were characterized before and after their immersion by XPS and AFM to evidence the formation of a coating on the different materials. The results are indicative of the presence of substituted phenyl groups on all the investigated surfaces. This study also aims at correlating grafting efficiency with metal reactivities and diazonium salt electronic properties by means of AFM and FT-IRRAS. For this purpose, zinc and nickel were chosen due to their opposite reducing properties and two diazonium salts were selected with electron-donor or -withdrawing para-substituents. The results tend to indicate that redox properties of both partners (diazonium + metal) are of prime importance for grafting to occur.