基于新型长周期光纤光栅的掺铒光纤放大器

报道了基于高频CO₂激光脉冲写入的新型长周期光纤光栅的低噪音掺铒光纤放大器,这种新型长周期光纤光栅是用大约几千Hz的高频CO₂激光脉冲对光纤玻璃热冲击作用而形成的.在铒纤中插入一个长周期光纤光栅,会明显减少掺铒光纤放大器的放大自发辐射(ASE)噪音.报道了两种低噪音掺铒光纤放大器,作为前置放大器和线路放大器,它们的ASE噪音指数分别从4.0 dB减少到3.5 dB和从4.8 dB减少到4.3 dB,并且在作为线放时,其小信号增益从30 dB提高到37 dB,降噪及提高增益效应十分显著.     

Fiber-Optic Backscattering Profile Measurements for Determination of the Optical Coefficients of Turbid Media

The necessity of using anisotropic approximation in techniques for determining optical parameters from the backscattered radiation profile is shown. A fiber-optic technique for simultaneous determination of the anisotropy parameter as well as the scattering and absorption coefficients of turbid media is proposed. It is based on the comparison of the experimental backscattered radiation profiles and those obtained by the numerical Monte Carlo method.     

一种控制掺铒光纤激光器超混沌的方法——非线性延时反馈参数调制法

提出一种非线性延时反馈参数调制法来控制混沌/超混沌，给出了利用这种方法控制处于超混沌状态的双环掺铒光纤激光器的方案.数值模拟表明，只要延时时间和反馈强度合适就可以把双环掺铒光纤激光器从超混沌状态成功地控制到不同的周期状态. 关键词： 掺铒光纤激光器 超混沌 非线性延时反馈参数调制 混沌控制     

Load-Carrying Capacity of Circular Plates Made of a Fiber-Reinforced Composite

The load-carrying capacity of circular plates made of a fiber-reinforced composite and loaded with axisymmetric transverse forces under axisymmetric boundary conditions is investigated. The plates can be freely supported or clamped along their contour. To the known yield condition used, in the plane of main bending moments, there correspond irregular hexagons, which depend on the mechanical properties of composite constituents and some characteristic geometrical parameters. It is shown that, depending on the ratio of ultimate radial and circumferential bending moments, in the plastic state, the circular plates (the central part of the clamped plates) take the form of a cone or a frustum of cone. For each of the cases, the limit load is found, which is a function of the above-mentioned mechanical parameters. The statically allowable fields of bending moments and the corresponding allowable fields of deflection rates are determined. The solutions found are exact. Special cases for the freely supported plates are analyzed, and the results obtained are presented in the form of graphs.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 2, pp. 177–192, March–April, 2005.     

三包层WⅠ和WⅡ型单模光纤波导色散特性的研究

研究了三包层WⅠ和WⅡ型单模光纤的波导色散特性。结果发现在相同条件下，三包层WⅠ和WⅡ型单模光纤零色散点的调节范围比传统的双包层W型单模光纤明显增大。详细分析了几何参量P、Q和光学参量R1、R2对单模传输时的波导色散特性和低次模截止频率的影响。所得的研究结果为获得更为理想的色散补偿、色散平坦光纤及设计新型无源光器件提供了重要的依据。计算波导色散的方法可推广到多包层光纤。     

Covalent functionalization of multi-walled carbon nanotubes by lipase

Lipase from Candida rugosa was covalently anchored onto acid-treated multi-walled carbon nanotubes (MWNTs) through a self-catalytic mechanism. A variety of characterization techniques including FTIR, Raman spectroscopy, and XPS were employed to demonstrate the formation of the ester linkage between lipase and MWNTs. The MWNTs-lipase biocomposites showed significantly increased solubility in some common-used organic solvents, such as THF, DMF and chloroform. This study may offer a novel and facile route for covalent modification of carbon nanotubes, and expand the potential utilization of both lipases and MWNTs in the fields of biocatalyst and biosensor.     

集中荷载下叠合梁抗剪强度

本文对低叠合面钢筋破简支在合梁二阶段受力的斜截面抗剪性能进行了试验研究，并运用非线性有限元分析和试验实测数据，得出了一个适合于集中荷载下高低叠合面叠合梁的抗剪强度计算公式．     

新型AFM探针的制备及应用

采用熔拉 -腐蚀复合方法 ,将普通单模石英光纤制成直锥形光纤探针。利用自制工具将探针打弯 ,制成悬臂式光纤探针 ,在AFM上取得了较理想的测试结果。将自制光纤探针和商用硅材料探针获得的两种扫描图像进行了对比 ,分析了悬臂式光纤探针的特点     

KrF准分子激光激发掺锗光纤折射率扰动的非线性过程

本文采用了一种简单的功率监测法,观察了KrF准分子激光对掺锗光纤折射率影响的非线性过程。观察到子纤芯折射率扰动过程中非稳定现象、饱和现象和折射率扰动的非线性。     

群色散光纤中高强度光脉冲传输与压缩的研究

考虑非线性四阶折射率,推导了光脉冲在群色散单模光纤中传输的非线性方程,并得到孤子型解析解.同时指出在Sech型光纤脉冲压缩实验中,光强度的阈值.