Nonlinear rheological behavior of silica filled solution‐polymerized styrene butadiene rubber

The reinforcement and nonlinear viscoelastic behavior have been investigated for silica (SiO₂) filled solution‐polymerized styrene butadiene rubber (SSBR). Experimental results reveal that the nonlinear viscoelastic behavior of the filled rubber is similar to that of unfilled SSBR, which is inconsistent with the general concept that this characteristic comes from the breakdown and reformation of the filler network. It is interesting that the curves of either dynamic storage modulus (G′) or loss tangent (tan δ) versus strain amplitude (γ) for the filled rubber can be superposed, respectively, on those for the unfilled one, suggesting that the primary mechanism for the Payne effect is mainly involved in the nature of the entanglement network in rubbery matrix. It is believed there exists a cooperation between the breakdown and reformation of the filler network and the molecular disentanglement, resulting in enhancing the Payne effect and improving the mechanical hysteresis at high strain amplitudes. Moreover, the vertical and the horizontal shift factors for constructing the master curves could be well understood on the basis of the reinforcement factor f(φ) and the strain amplification factor A(φ), respectively. The surface modification of SiO₂ causes a decrease in f(φ), which is ascribed to weakeness of the filler–filler interaction and improvement of the filler dispersion. However, the surface nature of SiO₂ hardly affects A(φ). © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2594‐2602, 2007     

Synthesis and characterization of functional gradient copolymers of allyl methacrylate and butyl acrylate

Functional spontaneous gradient copolymers of allyl methacrylate (A) and butyl acrylate (B) were synthesized via atom transfer radical polymerization. The copolymerization reactions were carried out in toluene solutions at 100 °C with methyl 2‐bromopropionate as the initiator and copper bromide with N,N,N′,N″,N″‐pentamethyldiethylenetriamine as the catalyst system. Different aspects of the statistical reaction copolymerizations, such as the kinetic behavior, crosslinking density, and gel fraction, were studied. The gel data were compared with Flory's gelation theory, and the sol fractions of the synthesized copolymers were characterized by size exclusion chromatography and nuclear magnetic resonance spectroscopy. The copolymer composition, demonstrating the gradient character of the copolymers, and the microstructure were analyzed. The experimental data agreed well with data calculated with the Mayo–Lewis terminal model and Bernoullian statistics, with monomer reactivity ratios of 2.58 ± 0.37 and 0.51 ± 0.05 for A and B, respectively, an isotacticity parameter for A of 0.24, and a coisotacticity parameter of 0.33. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5304–5315, 2006     

Preparation and properties of isobutylene–isoprene rubber–clay nanocomposites

Isobutylene isoprene rubber (IIR)‐clay nanocomposites have been prepared successfully by melt intercalation with maleic anhydride‐grafted IIR (Ma‐g‐IIR) and organophilic clay. In IIR‐clay nanocomposites, the silicate layers of the clay were exfoliated and dispersed into the monolayer. The nanocomposites exhibited greater gas barrier properties compared with those of Ma‐g‐IIR. When 15 phr clay was added, gas barrier properties were 2.5 times greater than those of Ma‐g‐IIR. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1182–1188, 2006     

Single electron transfer–degenerative chain transfer living radical polymerization of N‐butyl acrylate catalyzed by Na2S2O4 in water media

Living radical polymerization of n‐butyl acrylate was achieved by single electron transfer/degenerative‐chain transfer mediated living radical polymerization in water catalyzed by sodium dithionate. The plots of number–average molecular weight versus conversion and ln[M]₀/[M] versus time are linear, indicating a controlled polymerization. This methodology leads to the preparation of α,ω‐di(iodo) poly (butyl acrylate) (α,ω‐di(iodo)PBA) macroinitiators. The influence of polymerization degree ([monomer]/[initiator]), amount of catalyst, concentration of suspending agents and temperature were studied. The molecular weight distributions were determined using a combination of three detectors (TriSEC): right‐angle light scattering (RALLS), a differential viscometer (DV), and refractive index (RI). The methodology studied in this work represents a possible route to prepare well‐tailored macromolecules made of butyl acrylate in an environmental friendly reaction medium. Moreover, such materials can be subsequently functionalized leading to the formation of different block copolymers of composition ABA. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2809–2825, 2006     

Microemulsion photopolymerization of methacrylates stabilized with sodium dodecyl sulfate and poly(N-acetylethylenimine) macromonomers

Methyl methacrylate and butyl methacrylate were polymerized in oil-in-water microemulsions that were stabilized by sodium dodecyl sulphate (SDS). A poly(N-acetylethylenimine) (PNAEI) macromer was also included in the recipe, as a cosurfactant and a comonomer. Polymerizations were initiated by UV-irradiation. The average diameters of latex particles, obtained by STM, were in the range of 17-200 nm. The experimental data evidenced that the particle size was mainly dependent on the SDS/PNAEI ratio. Polymerization yields were around 75-85%. The synthesized copolymers have viscosity average molecular weights in the range of 2.1-2.4×10⁶ and glass transition temperatures of 38.0-43.5°C, lower than those obtained without using PNAEI. The investigation by means of FTIR and 1H-NMR techniques revealed that PNAEI was incorporated into the nanoparticles.     

有机硅及其改性聚合物膜用于有机溶剂水溶液的渗透汽化分离

采用室温固化硅橡胶及其它三种改性硅氧烷聚合物制成渗透汽化膜,分离丙酮(A),丁酮(B)、乙醇(E)及异丙醇(P)等有机物的水溶液。结果表明,随着透过温度提高、透量成指数关系增大,但对分离系数影响甚小。透量大小顺序为A>B>E>P,分离系数大小顺序为A>B>P>E,当膜材料中(CH_3)_2SiO链节含量由70%上升到100%时,有机物的透量及分离系数同时增加。     

Synthesis of N,N-diethyldithiocarbamate functionalized 1,4-polyisoprene, from natural rubber and synthetic 1,4-polyisoprene

N,N-Diethyldithiocarbamate functionnalized 1,4-polyisoprenes were prepared from 1,4-polyisoprenes (natural or synthetic). The syntheses were performed by nucleophilic addition of N,N-diethyldithiocarbamate salts upon oxirane rings of epoxidized units according to a SN2 mechanism with ring opening. Studies on model molecules of epoxidized 1,4-polyisoprene units (1,2-epoxy-1-methylcyclohexane and 4,5-epoxy-4-methyloctane) were previously achieved to develop the procedure. The best yields were obtained at low temperature in polar medium, and more especially in water with sodium N,N-diethyldithiocarbamate (DEDT-Na) as reagent. A diastereospecific addition was noted when reaction was performed in water with DEDT-Na. Afterwards, the developed procedure was successfully generalized to epoxidized synthetic polyisoprenes and epoxidized natural rubber (in THF, then in latex medium). Excellent results were obtained in latex medium with epoxidized natural rubber (ENR) latices. As with the models, a diastereospecific addition of sodium N,N-diethyldithiocarbamate trihydrate onto epoxidized 1,4-polyisoprene units of ENR was observed at the condition to bring the latex medium to pH 8 before introduction of DEDT-Na. Influence of temperature, drc, and DEDT-Na concentration were successively examined to determine the best conditions of the addition on ENR latices.     

Aging Process Effects on the Characteristics of Vacuum Residue Oxidation Products with the Addition of Crumb Rubber

This paper considers the effect of aging processes on viscoelastic characteristics of vacuum residue oxidation products modified with crumb rubber. Viscoelastic properties were compared to original bitumen raw material-vacuum residue and vacuum residue oxidation products during short-term and long-term aging. The complex shear modulus of the vacuum residue and its oxidation products decreased with an increase in temperature. Short-term aging resulted in increased shear modulus for all samples.The vacuum residue oxidation product modified with crumb rubber had the maximum values of the rutting parameter and fatigue parameter. There was an expansion of the temperature range of plasticity: for the vacuum residue oxidation product with crumb rubber, its value was 67.2 °C. The curves of the black diagram of the modified vacuum residue oxidation product are shifted towards smaller phase angles with the increase in the shear modulus, which indicates the increase in the stiffness and elasticity of the rubber bitumen binders. The vacuum residue oxidation product modified with crumb rubber corresponded to the rubber bitumen binder of the grade RBB 60/90, according to its physical and mechanical indicators.     

Polypropylene/poly(butyl methacrylate) blends prepared by diffusion and subsequent polymerization of butyl methacrylate in isotactic polypropylene pellets

Polypropylene/poly(butyl methacrylate)(PP/PBMA) blends were prepared by diffusion and subsequent polymerization of butyl methacrylate(BMA) in commercial isotactic polypropylene(iPP) pellets.The diffusion kinetics,diametrical distribution of PBMA in a pellet and phase morphology of a typical PP/PBMA blend were investigated.     

Crystalline Morphology and Nonisothermal Crystallization Behaviors of iPP/PcBR Blends

Isotactic polypropylene/poly(cis‐butadiene) rubber (iPP/PcBR) blends were prepared by melt mixing. The influence of PcBR content on crystalline morphology and nonisothermal crystallization behaviors of iPP was investigated by polarized optical microscopy (POM), small angle light scattering (SALS), and differential scanning calorimetry (DSC). The POM showed that an increase of PcBR ranging from 10 vol% to 40 vol% led to less perfection of spherulites, vaguer boundaries between spherulites, and smaller spherulite size, which was quantitatively validated by SALS. The presence of PcBR also remarkably affected the nonisothermal crystallization behaviors of iPP. An addition of PcBR caused higher crystallization peak temperature and a faster crystallization rate, meaning a heterogeneous nucleation effect of PcBR upon crystallization of iPP. For the same sample, the crystallization peak temperature moved to lower temperature and the crystallization rate increased as the cooling rate increased. The Ozawa and combined Avrami and Ozawa equations were used to describe the nonisothermal crystallization process of iPP and blends. The combined Avrami and Ozawa equation was more appropriate for the crystallization of the blends. Crystallization activation energy of iPP and blends was calculated by the Kissinger equation; the result showed that crystallization activation energy decreased as the content of PcBR increased from 30 vol% to 40 vol%.