Low velocity impact response of flax/polypropylene hybrid roving based woven fabric composites: Where does it stand with respect to GRPC?

Flax-PP based thermally bonded roving (TBR) has a unique structure where the flax fibres remain twist-free and fully aligned along the roving axis. The present study describes an experimental investigation on the low velocity impact (LVI) behaviour of the TBR based woven fabric composites and compares the same with plain woven glass fabric reinforced PP composites (GRPC). Two different fabric architectures namely plain woven (PW) and unidirectional (UD) are fabricated using flax/PP based TBR. These TBR based woven fabrics and the glass fabric/PP sheets are consolidated in a compression moulding machine and the resultant composite-laminates are tested for their LVI behaviour. The impact test results revealed that the glass/PP composites absorb more energy and exhibit a higher peak load than both TBR based PW and UD fabric composites. However, the specific load and energy of all flax/PP composites are higher than the glass/PP composite. The damage tolerance of all composite laminates are evaluated by comparing their flexural strength before and after the impact. It is observed that the proportionate loss in flexural strength due to impact thrust is larger in case of glass/PP composites than all flax-PP composites.     

Electrochemical Oxidative Determination and Electrochemical Behavior of 4‐Nitrophenol Based on an Au Electrode Modified with Electro‐polymerized 3,5‐Diamino‐1,2,4‐triazole Film

A simple and fast electrochemical method was described and evaluated to determine the hazardous compound, 4‐nitrophenol (4NP). In this work, concentration of 4NP was determined by differential wave voltammetry (DPV). A gold electrode (Au) was modified with 3,5‐diamino‐1,2,4‐triazole (35DT). The modified electrode (35DT‐Au) was characterized by using electrochemical impedance spectroscopy (EIS), fouirer transform infrared spektrofotometre (FTIR), cyclic voltammetry (CV) and DPV. The modified electrode showed more sensitivity towards 4NP compared to unmodified one. A wide linear concentration range from 0.24 to 130.6 μM was obtained for 4NP with a detection limit of 0.09 μM. In the reproducibility and repeatability studies, the relative standard deviation (RSD%) values of the method were obtained as 3.72 % and 2.56 %, respectively, which are acceptable values. This proposed method was successfully used for the analysis of 4NP in lake and tap water samples. Simplicity, sensitivity, selectivity and high efficiency of the proposed method can be used in routine analysis of trace amounts of 4NP in polluted waters.     

Multivalent ions and biomolecules: Attempting a comprehensive perspective

Ions are ubiquitous in nature. They play a key role for many biological processes on the molecular scale, from molecular interactions, to mechanical properties, to folding, to self-organisation and assembly, to reaction equilibria, to signalling, to energy and material transport, to recognition etc. Going beyond monovalent ions to multivalent ions, the effects of the ions are frequently not only stronger (due to the obviously higher charge), but qualitatively different. A typical example is the process of binding of multivalent ions, such as Ca²⁺, to a macromolecule and the consequences of this ion binding such as compaction, collapse, potential charge inversion and precipitation of the macromolecule. Here we review these effects and phenomena induced by multivalent ions for biological (macro)molecules, from the “atomistic/molecular” local picture of (potentially specific) interactions to the more global picture of phase behaviour including, e. g., crystallisation, phase separation, oligomerisation etc. Rather than attempting an encyclopedic list of systems, we rather aim for an embracing discussion using typical case studies. We try to cover predominantly three main classes: proteins, nucleic acids, and amphiphilic molecules including interface effects. We do not cover in detail, but make some comparisons to, ion channels, colloidal systems, and synthetic polymers. While there are obvious differences in the behaviour of, and the relevance of multivalent ions for, the three main classes of systems, we also point out analogies. Our attempt of a comprehensive discussion is guided by the idea that there are not only important differences and specific phenomena with regard to the effects of multivalent ions on the main systems, but also important similarities. We hope to bridge physico-chemical mechanisms, concepts of soft matter, and biological observations and connect the different communities further.     

The effect of variety seeking behaviour on optimal product positioning

In this paper we develop a stochastic (first order Markovian) consumer choice model that represents variety seeking behaviour and we investigate the practical implications of this model for optimal product positioning relative to a zero order model that does not incorporate variety seeking. We show that the optimal positioning implications of a variety seeking process is indeed different than those of a (no-variety-seeking) zero order process. Based on intuition, one might expect increased variety seeking to imply that firms should increase the distance between their products in an attribute space. In fact, we show that this effect does occur for relatively low share brands. But just the opposite effect holds for relatively high share brands. That is, variety seeking behaviour generates a desire to more differentiation among low share brands, and a desire for less differentiation among high share brands.     

含能材料HMX-RDX的热行为研究

采用差示扫描量热法研究了含能材料1,3,5,7-四硝基-1,3,5,7-四氮杂环辛烷-环三甲撑三硝胺(HMX-RDX)的热行为。结果表明,当m(HMX)∶m(RDX)=25∶75时HMX和RDX达到了共熔。随着RDX含量的增加,HMX-RDX的晶型转变温度有所升高,晶型转化的热焓逐渐减少,共熔热焓却随之增加,共熔温度基本保持不变。     

Tensile properties of microtubules: A study by nonlinear molecular structural mechanics modelling

A nonlinear molecular structural mechanics (MSM) model is proposed in this paper for studying the tensile properties of microtubules (MTs). In the nonlinear MSM models, the interactions between tubulin monomers in MTs are treated as nonlinear axial and torsional springs, whose stiffness coefficients are extracted from all-atom molecular dynamics simulations. The Young's modulus and fracture properties of MTs under tension extracted from the present nonlinear MSM models are found to agree well with the existing simulation and experiment results, which shows the efficiency and accuracy of the proposed nonlinear MSM models. In addition, the nonlinear MSM models are also extended to investigate the tensile properties including Young's modulus and fracture strain of MTs possessing lattice defects. The results obtained from nonlinear MSM models are utilized to develop a predictive equation for quickly predicting the tensile properties of MTs with different lattice defect levels.     

Instantaneous work hardening behaviour of two-phase tungsten heavy alloys: a phenomenological approach

ABSTRACT

The present work describes a phenomenological approach to explain the instantaneous behaviour of tungsten heavy alloys (WHAs) in heat-treated and swaged conditions. The strengths and elongation values of heat-treated materials are lower and higher than those of the swaged samples respectively. The heat-treated materials exhibit two slopes in true stress–true plastic strain curves and follow the Ludwigson constitutive equation. On the other hand, swaged materials display a single slope and adhere to typical Swift constitutive equation. The latter reflect the presence of pre-strain in the materials due to swaging deformation. The fracture surfaces in heat-treated materials consist of W-W decohesion along with matrix rupture and W-cleavage, while swaged samples consist of mainly W-cleavage. Both the materials display three typical stages (I, II and III) of work hardening. The second derivatives of true stress–true plastic strain curves of these alloys exhibit a perfect parabola although the nature of true stress–true strain as well as true stress–true plastic strain curves is quite different in heat-treated and swaged materials. This has been observed for the first time in WHAs consisting of matrix and W-grains. The shape of the parabola is simple and easy to fit. The fitting parameters of parabolas have been successfully employed to explain the flow behaviour of a large number of tungsten heavy alloys having two-phase microstructure in different processing conditions.     

THE CRYSTALLIZATION BEHAVIOR OF URETHANE SUBSTITUTED POLYDIACETYLENE

The crystalline behavior of urethane substitute polydiacetylene was studied by using pohrized light and electron microscopy. The lamellar morphological structure was observed in the crystallized films. The thickness of lamellae is about 300A, being independent of the crystalline temperature. But the size and density of lamellae were dependent on the crystallization temperature. If the molten film was sheared during the crystallzation process the oriented lamellae grew with their long axes perpendicular to the direction of shear and the chain direction was normal to the lamellar surface.     

On the thermal behaviour of acetylphenyl-hydroxyaceticacid-4-nitrobenzyl esters

The 4-nitrobenzyl ester of acetylphenylhydroxyacetic acid differs in its melting behaviour from other nitrobenzyl esters of phenylhydroxyacetic or acetylphenylhydroxyacetic acids, the racemate having a higher melting point than the enantiomers. By means of thermal analysis, IR spectroscopy and X-ray diffractometry the ester can be shown to occur in two crystalline modifications. In the process of solidification of the molten mass, at first a modification of higher energy is formed, obviously being caused by an excess of one enantiomer, which is then exothermally rearranged in the lattice of the racemate.     

Polarity and steric effect of the lateral substituent on the mesophase behaviour of some newly prepared liquid crystals

Eight homologous series of 2- (or 3-) substituted phenyl 4?-(4?-alkoxy phenylazo) benzoates (In_a–h) were prepared in which, within each homologous series, the length of the terminal alkoxy group varies between 6, 8, 10 and 12 carbons, while the other substituent, X, is a laterally attached polar group that alternatively changed from CH₃, H, F, Br and CN. Compounds prepared were characterised by infrared and ¹H-NMR spectroscopy, and their mesophase behaviour investigated by differential scanning calorimetry and identified by polarised light microscopy. The results were discussed in terms of polarity and steric effects. The stability of the mesophase was correlated once with the dipolar anisotropy of the whole molecule and another with the dipolar anisotropy of the substituent, X. A comparative study was made between the investigated compounds and their previously prepared linear 4-substituted isomers, namely 4-substituted phenyl 4?-(4?-alkoxy phenylazo) benzoates (In_i–k).