Studies on the Phase Separation of Poly(Ether Imide)‐Modified Cyanate Ester Resin

Abstract

A high temperature thermosetting bisphenol‐A dicyanate (BADCy) was blended with a novel thermoplastic poly(ether imide) (PEI) at various composition. The phase separation behavior during isothermal curing was studied by differential scanning calorimeter (DSC), time‐resolved light scattering (TRLS), scanning electron microscopy (SEM), and rheological measurements. The results suggested that the phase structure changed from separated phase, via co‐continuous phase, to phase inversion with the increase of the PEI content. The curing conversion of BADCy was slightly affected by the composition in the blend and the curing rate was decreased with the increase of PEI content. The co‐continuous phase morphology was attributed to a spinodal decomposition. The initial concentration of PEI had an effect on the rheological behavior during phase separation. It was found by tensile test that the blend with 15 wt.% PEI had higher tensile strength and elongation at break than that without PEI.     

Living ring-opening metathesis polymerization of norbornenes bay-functionalized perylene diimides

Ring-opening metathesis polymerization (ROMP)-derived poly(oxanorbornene imide)s bearing bay-linked mono - alkoxy -M1 and 1,7-di-alkoxy M2 functionalized perylene diimides (PDIs) were synthesized using Grubb's third ( G3 ) and Hoveyda-Grubbs second generation ( HG2 ) ruthenium-alkylidene metathesis initiators. The mono-alkoxy-derived PDI-based non-ladderphane polymer poly M1 displayed 67% to 77% of the trans olefin content in the polymer chain depending on the initiator used for the polymerization. When using the symmetrical 1,7-di-alkoxy-derived PDI-based polymer poly M2 having the ladderphane type-structure, this displayed a significant amount of cis and trans olefin contents in the polymer chains, irrespective of the type of initiators used for the polymerization. ROMP of both monomers M1 and M2 proceeded in a well-controlled manner with a linear dependence of molecular weight on the monomer/initiator ratio using G3 as initiator. Optical properties of the ladderphane-based poly M2 and non-ladderphane-based poly M1 were characterized in both solution and the film state. X-ray diffraction (XRD) analysis for all the polymers showed significant π-stacking in the thin film state with ordered molecular packing and closer values of d-spacing for both poly M1 and poly M2 . Film morphology examined by AFM elucidated homogenous smooth polymer surface for both polymers in general, but with some irregularities observed for poly M1 . In addition, CV analysis revealed both polymers could be good candidates as electron-accepting materials, with excellent film-forming ability, and thermal stability.     

Influence of imide functionalized organo‐modified Mg‐Al layered double hydroxide on the thermal and mechanical properties of new aliphatic‐aromatic poly (amide‐imide)

A new dicarboxylic acid modified Mg‐Al LDH (DLDH) containing imide groups was prepared and its effects on the thermal and mechanical properties of the new synthesized aliphatic‐aromatic poly (amide‐imide) (PAI) were investigated via preparation of PAI/nanocomposite films by solution casting method. The results of X‐ray diffraction (XRD), field emission‐scanning electron microscopy (FE‐SEM) and transmission electron microscopy (TEM) showed a uniform dispersion for LDH layers into the PAI matrix. For comparison, the effects of polyacrylic acid‐co‐poly‐2‐acrylamido‐ 2‐methylpropanesulfonic acid (PAMPS‐co‐PAA) modified Mg‐Al LDH (ALDH) on the PAI properties were also studied. The thermogravimetric analysis (TGA) results exhibited that the temperature at 5 mass% loss (T₅) increased from 277 °C to 310 °C for nanocomposite containing 2 mass% of DLDH, while T₅ for nanocomposite containing 2 mass% of ALDH increased to 320 °C, along with the more enhancement of char residue compared to the neat PAI. According to the tensile test results, with 5 mass% DLDH loading in the PAI matrix, the tensile strength increased from 51.6 to 70.8 MPa along with an increase in Young's modulus. Also the Young's modulus of PAI nanocomposite containing 5 mass% ALDH reduced from 1.95 to 0.81 GPa.     

Synthesis of a Novel Dispiroheterocyclic Framework via the Regioselective 1,3‐Dipolar Cycloaddition Reaction of Azomethine Ylides

2‐Arylidene‐1,3‐indanediones undergo regioselective 1,3‐dipolar cycloaddition with the azomethine ylide generated from acenaphthenequinone and sarcosine to afford a rare class of complex dispiropyrrolidines in good yield. Single‐crystal X‐ray crystal analysis of one of the products confirms the structure and regiochemistry of the cycloaddition.     

Synthesis and Stereochemistry of Optically Active Selenium and Tellurium Compounds

Abstract

The synthesis and stereochemistry of tricoordinated optically active selenium and tellurium compounds are described. Telluronium salts, telluronium imides, and seleninic acids were prepared and optically resolved by fractional recrystallization of diastereomeric mixtures or by chromatography using a chiral column of racemic mixtures. Diphenyl dichalcogenides also were optically resolved by chiral crystallization. Their absolute configurations were determined or estimated based on X-ray crystallographic analysis, specific rotations, and circular dichroism spectra. The kinetic studies and the mechanism for the racemization were also studied.     

THERMOPLASTIC ELASTOMERS. II. POLY(ETHER-ESTER-IMIDE)S BASED ON 1,4-DIAMINOBUTANE,TRIMELLITIC ANHYDRIDE, 1,4-DIHYDROXYBUTANE,AND POLY(ETHYLENE OXIDE)S

A series of new poly(ether-ester-imide)s, PEEIs, was prepared from an imide dicarboxylic acid based on 1,4-diaminobutane and trimellitic anhydride. This imide dicarboxylic acid polycondensed with 1,4-dihydroxybutane formed the hard segments and poly(ethylene oxide), PEO-1000, or mixtures of PEO-1000 and poly(tetramethylene oxide), PTMO-1000, were used as soft segments. Whenever PTMO-1000 was used as comonomer, macrophase separation was observed at the end of the polycondensation. However, this macrophase separation had little influence on the mechanical properties. A poly(ether-esterimide), PEEI, containing neat PEO-1000 was characterized by dynamic mechanical thermoanalysis, stress-strain and hysteresis measurements, and by melt rheology. The mechanical properties were compared with those of an analogous PEEI containing neat PTMO-1000 and with those of a poly(ether-ester), PEE, based on poly(butylene terephthalate) hard segments and PTMO-1000.     

New Fluorinated Poly(imide siloxane) Random and Block Copolymers with Variation of Siloxane Loading

Several new random and block copoly(imide siloxane)s have been prepared by the solution polycondensation of commercially available 4,4′-oxydianiline (ODA) and amino-propyl terminated polydimethylsiloxane (APPS) with 4,4′-(hexafluoro-isopropylidene)diphthalic anhydride (6FDA). The siloxane loading was kept to 10, 20, 30, 40 and 50 wt% in the copolymers. The random copolymers were prepared by a one pot solution imidization technique, and two pot solution imidization technique was adopted for the synthesis of the block copolymers. The diamine ODA and the dianhydride 6FDA composed the hard block segment, while APPS and 6FDA composed the soft block segment. The hard block length was kept constant while the soft block lengths were varied by varying the siloxane loading. Accordingly, block copoly(imide siloxane)s were prepared on increasing the soft block lengths (DP) from 3 to 6, 10, 18 and 36 for fixed hard block length of 22. The resulting polymers have been well characterized by IR, NMR and GPC techniques. Thermal and mechanical properties of the random and block copolymers were compared with the already reported homopolyimide without siloxane moiety.     

Cyclic Aromatic Polyamides via the Triphenylphosphite Method

Abstract

5‐tert‐Butyl‐isophthalic acid (TIPA) was polycondensed with three different aromatic diamines by means of triphenylphosphite (TPP) and pyridine. The resulting polyamides were characterized by solution viscosities and MALDI‐TOF mass spectra (m.s.). These m.s. revealed significant fractions of cyclic oligo‐ and polyamides in all samples. In polyamides of high molecular weight, only cycles were detectable (observed up to masses of 13,000 Da). Three poly(amide‐imide)s were prepared by TPP‐mediated polycondensation of trimellitic anhydride (TMA) and three aromatic diamines. Although relatively high molar masses were obtained, the MALDI‐TOF m.s. displayed the peaks of linear chains in addition to those of cyclic polymers. The results together suggest that the side reactions mainly occur at the amino endgroups.     

Synthesis,Characterization and Comparison of Properties of Novel Fluorinated Polyimides Derived from Bisphenol–A‐di(phthaleic anhydride)

Four new poly(etherimide)s have been synthesized by reaction with commercially available bisphenol‐A‐(diphthaleic anhydride) (BPADA) with four different kinds of diamines, namely 4,4′‐bis(p‐aminophenoxy‐3,3″‐trifluoromethyl) terphenyl,4,4′‐bis(3″‐trifluoromethyl‐p‐aminobiphenyl ether)biphenyl,2,6‐bis(3′‐trifluoromethyl‐p‐aminobiphenyl ether)pyridine, 2,5‐bis(3′‐trifluoromethyl‐p‐aminobiphenylether)thiopene. The poly(etherimide)s are named as 1a, 1b, 1c and 1d, respectively. The synthesized polyimides show good solubility in various organic solvents. The polyimide films had low water absorption of 0.19–0.30% and low dielectric constant of 2.79–3.1 at 1 MHz. These polyimides showed very high thermal stability with decomposition temperature (5% wt loss) up to 522°C in nitrogen. Transparent thin films of these polyimides exhibited tensile strength up to 97 MPa, a modulus of elasticity up to 1.56 GPa and elongation at break up to 20%.