实验室隔声测量中试件洞填隙墙传声影响的检验

文章探讨了实验室建筑构件隔声测量中填隙墙传声影响的检验与修正方法。通过实验分析,给出了三种可用于不同隔声量构件的门、窗和玻璃试件隔声测量的填隙墙构造方式。     

雷达回波资料反演海洋波导中观测值权重的确定

提出采用一种与电磁波传播损耗相类似的指数衰减形式来描绘观测值权重随距离的变化,结合标准的统计反演算法来测试不同的观测值权值对反演速度与精度的影响.结果表明,指数衰减形式能较好地描绘观测值权值随距离的变化情况;其中衰减指数的选取是关键.合理地选取衰减指数可较好地改进反演的速度与精度.对于不同频率的电磁波,最优衰减指数是各不相同的. 关键词： 海洋波导 观测值权重 衰减指数 反演算法     

长周期光纤光栅折射率特性仿真的新方法

基于长周期光纤光栅的模式耦合机理,提出一种快速模拟长周期光纤光栅折射率特性的方法。该方法在计算包层模式的有效折射率时分开计算,在环境折射率小于包层折射率时采用二分法和分步搜索法结合计算包层模式的有效折射率,在环境折射率大于包层折射率时采用Nelder-Mead加分步搜索法求解包层模式的有效折射率。在应用谐振波长的决定式求解与环境折射率的匹配的谐振波长时,采用变区间应用二分法求解而不是传统的逐步搜索法求解谐振波长。数值结果与实验结果做了对比,两者基本一致。实践证明,该方法方便快捷,比一般的方法速度提高7倍以上。     

大气湍流光学参数分析

利用两种不同大气湍流结构常数模型,讨论了不同高度的湍流对大气湍流光学参数的影响。通过理论计算得出:相干长度和对数振幅起伏方差主要由低层大气湍流决定,而等晕角、倾斜等晕角、格林伍德频率和泰勒频率由对流层顶附近的高层湍流决定。分析了垂直高度30 km以下的3部分大气湍流对等晕角的贡献比例,在给定的不同强度湍流下,对流层顶附近的高层大气湍流贡献比例都大于25％,而低层大气湍流的贡献比例都小于3%。     

Micro‐Raman study of exfoliated Bi2Sr2CaCu2O8+δ single crystals with different thicknesses

Exfoliated Bi₂Sr₂CaCu₂O_8+δ (Bi‐2212) single crystals were prepared by micromechanical cleavage of bulk Bi‐2212 single crystals on SiO₂/Si substrates. Room temperature micro‐Raman spectra were collected using a 532‐nm laser source. The evolutions of the spectra of A_1g (Bi), A_1g (Sr), and A_1g (O_Bi) Raman modes with different thicknesses of the samples were studied. The refractive index of Bi‐2212 single crystal was obtained by studying the intensity evolutions based on the interference effect. The observed wavenumber shifts of the A_1g (Bi), A_1g (Sr), and A_1g (O_Bi) modes were analyzed. Copyright © 2011 John Wiley & Sons, Ltd.     

Theoretical expression for change of extraordinary refractive index in annealed proton exchanged LiNbO3 optical waveguides

A general expression for the change in extraordinary refractive index of the annealed proton exchanged LiNbO₃ waveguide has been deduced. The expression deduced explains the experimental results of decrease in change of extraordinary refractive index with annealing. The effect of annealing time has also been incorporated following Cao's model (Cao, Ramaswamy, Srivastava, J. Lightwave Technol. 10 (1992) 1302–1313). The concentration profile of protons in the annealed waveguide has been deduced theoretically, which is consistent with the previous results. The spontaneous polarization has been considered as the central mechanism for change in extraordinary refractive index due to proton exchange with annealing.     

基于线偏振光反射率测量介质折射率的研究

研究线偏振光的振幅反射率与介质折射率的关系,提出一种测量介质材料折射率的方法。文中从菲涅耳公式出发,推导出各向同性介质的线偏振光反射率与折射率的关系式,给出基于线偏振光反射率测定介质折射率的原理。设计实验方案,在不同入射角情况,定出线偏振光p方向和s方向两种线偏振光在玻璃表面的反射率,得到线偏振光振幅反射率随入射角变化的实验曲线。依此实验数据得出材料的折射率。结果表明,测出的介质材料的折射率与理论值相符,所采取的测定方案可行。     

Growth and electronic properties of ultra-thin Ag films on Ni(1 1 1)

We studied the growth mode and electronic properties of ultra-thin silver films deposited on Ni(1 1 1) surface by means of scanning tunnelling microscopy (STM) and angle resolved photoemission spectroscopy (ARPES). The formation of the 4d-quantum well states (QWS) was analysed within the phase accumulation model (PAM). The electronic structure of the 1 ML film is consistent with the silver layer which very weakly interacts with the supporting surface. The line-shape analysis of Ag-4d_xz,yz QWS spectrum support the notion of strong localization of these states within the silver layer. The asymmetry of the photoemission peaks implies that the decay of the photo-hole appears to be influenced by the dynamics of the electrons in the supporting surface.     

结温对高压白光LED光谱特性的影响

高压LED因其自身突出的特点在照明领域有着潜在的应用优势,但作为一种新型功率LED,其光电热特性仍需深入研究。该实验对6和9V GaN基高压LED芯片进行了相同结构和工艺条件的封装,对封装样品进行了10~70℃的变温度光谱测试,并进行了从控温平台温度到器件结温的转换。为保证器件的电流密度相同,6和9V样品光谱测试的工作电流分别设定为150和100mA。结果显示,结温升高会导致蓝光峰值波长红移、波长半高宽增大、光效下降和显色指数上升等现象。在相同平台温度和注入功率下,9V样品的结温低于6V样品;随着温度的升高,9V样品波长半高宽的增加量比6V样品少1.3nm,光效下降量少1.13lm·W~(-1),显色指数上升量少0.28。以上表明,与低压LED相比,高压LED有着更低的工作结温和更小的温度影响。原因在于,相同环境温度下高压LED具有更好的电流扩展性和更少的发热量。此特性在高压LED的研究、发展与应用等方面具有参考价值。此外,峰值波长仍与结温有着较好的线性度,在光谱设备精度较高的情况下可继续作为结温的敏感参数。     

红外探测装置中光谱分光镜的设计与制备

在红外探测装置中,光谱分光镜是用来把3 μm～5 μm和8 μm～12 μm 2个波段的光谱分开的零件.介绍了一种在通用镀膜机上制备光谱分光镜的新工艺.在该膜系的设计过程中,把Willey公式引入到对其平均透过率最高值进行估算的过程中,同时针对国产镀膜机控制精度不高的特点,尽量使用规整膜层进行设计.为了进一步提高8 μm～12 μm波段的透过率,在膜系的最外侧引进了一层自行配制的低折射率氟化物材料,制备出了符合技术指标的红外光谱分光镜.