多巴酚丁胺的流动注射化学发光法测定

在盐酸介质中 ,高锰酸钾可氧化多巴酚丁胺产生化学发光 ,甲醛对该反应有较强的增敏作用 ,据此 ,建立了流动注射化学发光法测定多巴酚丁胺的方法 ;方法的线性范围为0.1～100mg·L -1,检出限为0.07mg·L -1 ,相对标准偏差为1.2 %(n=11,ρ=1.0mg·L -1) ;该法用于药物中多巴酚丁胺含量的测定 ,结果令人满意。     

流动注射原子吸收光谱法测定富硒天麻、葡萄及大米中的硒

建立了流动注射氢化物发生-原子吸收光谱法测定富硒天麻、葡萄及大米中硒的方法。测定硒的线性范围为0．33μg/L-50μg/L，相对标准偏差小于3％，加标回收率为93％-106％。方法已广泛应用于实际样品中微量硒的测定。     

Application of enzyme-field effect transistor sensor arrays as detectors in a flow-injection analysis system for simultaneous monitoring of medium components. Part II. Monitoring of cultivation processes

Glucose, maltose, sucrose, lactose, ethanol and urea concentrations were monitored simultaneously during the cultivation of Escherichia coli and Saccharomyces cerevisiae by means of enzyme field effect transistors (EnFETs) applying glucose dehydrogenase (GDH), maltase (MAL)/GDH, invertase (INV)/GDH, β-galactosidase (β-GAL)/galactosedehydrogenase (GALDH), alcoholdehydrogenase (ADH)/aldehydedehydrogenase (ALDH), and urease. These enzymes were (co)immobilized on the pH sensitive gates of an eight-FET array. The FET array was integrated in a commercial FIA system.     

注入控制铜蒸气激光方向性时间过程测量

实验研究了注入控制对铜蒸气激光非稳腔输出光束质量的影响，从输出光发散角时间分辨过程的测量结果说明注入加速被注入腔内激光发散角的减小过程。由于被注入腔内放大自发辐射的存在，为得到较好的注入控制效果，注入光的脉宽和进入被注入腔的延时必须恰当。     

HPLC法测定阿奇霉素葡萄糖注射液中阿奇霉素的含量

利用高效液相色谱法，以VP-ODS型色谱柱，乙腈-异丙醇-水-氨水（60：25：15：0.1)为流动相，于210nm波长处测定了阿奇霉素葡萄糖注射液中阿奇霉素葡萄糖注射液中阿奇霉素的含量。阿奇霉素的浓度在0.75-1.75mg/mL线性关系良好，线性方程的A=881910.4c-16208.2，相关系数r=0.9999。阿奇霉素的平均回收率为99.59%，测定结果的相对标准偏差为1.31%。     

Measurement of small-signal and large-signal responses of packaged laser modules at high temperature

In this paper, the pulsed injection method is extended to measure the chip temperature of various packaged laser modules, such as the DFB laser modules, the FP laser modules, and the EML laser modules. An optimal injection condition is obtained by investigating the dependence of the lasing wavelength on the width and period of the injection pulse in a relatively wide temperature range. The small-signal frequency responses and large-signal performances of packaged laser modules at different chip temperature are measured. The adiabatic small-signal modulation characteristics of packaged LD are first extracted. In the large-signal measurement, the effects of chip temperature, bias current and driving signal on the performances of the laser modules are discussed. It has been found that the large-signal performances of the EML modules depend on the different red-shift speeds of the DFB and EAM sections as chip temperature varying, and the optimal characteristics may be achieved at higher temperature.     

ECR-SFC轴向注入系统聚束器效率的研究

为了减少目前SFC轴向注入系统中聚束器杂散电场对束流轴向注入效率的影响, 提高新系统中SFC的束流俘获效率, 参考原始设计, 对目前聚束器的电极结构进行了设计改进. 两种情况下的聚束器杂散场对注入效率影响的计算表明, 改进后0B02的聚束效率较目前有较大提高. 同时计算了束流空间电荷效应对聚束效率的影响, 据此对新SFC轴向注入系统中聚束器的位置进行了重新调整.     

Fast Fourier Continuous Cyclic Voltammetry at Gold Ultramicroelectrode in Flowing Solution for Determination of Ultra Trace Amounts of Penicillin G

In this work, for the first time a fast continuous cyclic voltammetry was used as a highly sensitive detection method for Penicillin G in a flow‐injection system. A special computer‐based numerical calculation method (using Fast Fourier Transformation) is introduced here for enhancing the analyte signal and noise reduction. During the measurements, the potential waveform (consists of potential steps for cleaning, stripping and potential ramp) was continuously applied on an Au disk microelectrode (with a radius 12.5 μm in radius). The stripping time was less than 200 ms. Effects of rest potential, sweep rate, and delay time on the sensitivity of the method were investigated. The limit of detection of the method was 1.0 × 10^?11 M. The detection limit of the method is 660 times lower than the most sensitive reported method. The relative standard deviation of the method at 1.0×10^?7 M of Penicillin G was 2.7% for 10 runs.     

Matrix assisted pulsed laser evaporation processing of triacetate-pullulan polysaccharide thin films for drug delivery systems

We report the first successful deposition of triacetate-pullulan polysaccharide thin films by matrix assisted pulsed laser evaporation. We used a KrF* excimer laser source (λ = 248 nm, τ ≈ 20 ns) operated at a repetition rate of 10 Hz. We demonstrated by FTIR that our thin films are composed of triacetate-pullulan maintaining its chemical structure and functionality. The dependence on incident laser fluence of the induced surface morphology is analysed.