STUDIES OF MULTICOMPONENT COMPLEX OXIDE CATALYSTS FOR OXIDATIVE COUPLING OF METHANE VI.SURFACE BASICITY AND SURFACE ACTIVE OXYGEN SPECIES OF LiTi_xLa_(1-x)O_2 λ MULTICOMPONENT OXIDE CATALYSTS

The surface basicity of Ti-La-Li multicoinponent oxides has been investigated by means of CO2-TPD. The experiment results show that C2 (C2H6 C2H4) selectivity is related to surface basic strength. The surface active oxygen species have also been characterized by means of XPS, O2-TPD and so on. It has been indicated that C2 selectivity and CH4 conversion are correlated with lattice oxygen and the adsorbed oxygen on the surface of the catalyst respectively In the O2-TPD experiments, it has also been found that there are three kinds of oxygen species on the surface of the series catalvsts, which are a (100℃ 750℃) Among them α-oxvgen causes deep oxidation whileβand γ oxygen species are related to oxidalive coupling of methane (OCM).     

Separation of chlamydosporol epimers by reversed-phase HPLC using commercial solvent optimisation software

Summary Two epimers of the mycotoxin chlamydosporol were separated by HPLC on an RP-18 column using a quaternary mobile phase consisting of water (79.1%), methanol (10.0%), acetonitrile (10.4%) and tetrahydrofuran (0.5%), with a flow rate of 1 ml min^–1. This optimal composition of mobile phase, with which the resolution value for the two epimers (1 and2) was 2.73 with retention times of 5.88 and 7.12 min, respectively, was achieved by the application of Philips Solvent Optimisation Software PU 6100. The presence of free silanols on the stationary phase was shown to be an essential requirement for the separation of the chlamydosporol epimers.     

Determination of arsenic in mussels by slurry sampling and electrothermal atomic absorption spectrometry (ETAAS)

A method for the determination of arsenic in slurries of mussel tissue using palladium-magnesium nitrate as modifier was optimized. The slurry was stabilized by a 0.015% (v/v) of Triton X-100. To achieve complete mineralization the slurries were ashed at 480 °C for 10s in an air flow (50 ml/min) and at 1200 °C for 15s in an argon flow (300 ml/min) in the presence of Pd—Mg(NO₃)₂ as modifier. The optimum atomization temperature was 2200 °C. The precision and accuracy of the method were studied using the Reference Material BCR n ° 278 Mussel Tissue (Mytilus edulis). The detection limit (LOD) of the final slurry solution was 1 g/l of arsenic corresponding to an arsenic level in the mussel of 1.3 g/g, for a 0.5% (m/v) slurry. Results of calibration using aqueous standards and the standard additions method were compared. The method was applied to the determination of arsenic in mussels from the Galician coast. The levels found lie between 2 and 9.3 g/g of arsenic.     

Optimization of a GFAAS method for determination of total inorganic arsenic in drinking water

The new 10 μg l⁻¹ arsenic standard in drinking water has been a spur to the search for reliable routine analytical methods with a limit of detection at the μg l⁻¹ level. These methods also need to be easy to handle due to the routine analyses that are required in drinking water monitoring. Graphite furnace atomic absorption spectrometry (GFAAS) meets these requirements, but the limit of detection is generally too high except for methods using a pre-concentration or separation step. The use of a high-intensity boosted discharge hollow-cathode lamp decreases the baseline noise level and therefore allows a lower limit of detection. The temperature program, chemical matrix modifier and thermal stabilizer additives were optimized for total inorganic arsenic determination with GFAAS, without preliminary treatment. The optimal furnace program was validated with a proprietary software. The limit of detection was 0.26 μg As l⁻¹ for a sample volume of 16 μl corresponding to 4.2 pg As. This attractive technique is rapid as 20 samples can be analysed per hour. This method was validated with arsenic reference solutions. Its applicability was verified with artificial and natural groundwaters. Recoveries from 91 to 105% with relative standard deviation <5% can be easily achieved. The effect of interfering anions and cations commonly found in groundwater was studied. Only phosphates and silicates (respectively at 4 and 20 mg l⁻¹) lead to significant interferences in the determination of total inorganic arsenic at 4 μg l⁻¹.     

Determination of Inorganic Arsenic Species by Electrochemical Hydride Generation Atomic Absorption Spectrometry with Selective Electrochemical Reduction

A new direct procedure for the determination of inorganic arsenic species was developed by electrochemical hydride generation atomic absorption spectrometry （EcHG-AAS） with selective electrochemical reduction. The determination of inorganic arsenic species is based on the fact that As（Ⅲ） shows significantly higher absorbance at low electrolytic currents than As（Ⅴ） in 0.3 mol·L^-1 H2SO4. The electrolytic current used for the determination of As（Ⅲ） without considerable interferences of As（Ⅴ） was 0.4 A, whereas the current for the determination of As（Ⅲ） and As（Ⅴ） was 1.2 A. For equal concentrations of As（Ⅲ） and As（Ⅴ） in a sample, the interferences of As（Ⅴ） during the As（Ⅲ） determination were smaller than 5%. The absorbance for As（Ⅴ） could be calculated by subtracting that for As（Ⅲ） measured at 0.4 A from the total absorbance for As（Ⅲ） and As（Ⅴ） measured at 1.2 A, and then the concentration of As（Ⅴ） can be obtained by its calibration curve at 1.2 A. The methodology developed provided the detection limits of 0.3 and 0.6 ng·mL^-1 for As（Ⅲ） and As（Ⅴ）, respectively. The relative standard deviations were of 3.5% for 20 ng·mL^-1 As（Ⅲ） and 3.2% for 20 ng·mL^-1 As（Ⅴ）. The method was successfully applied to determination of soluble inorganic arsenic species in Chinese medicine.     

Simple Method for Simultaneous Determination of Selenium and Arsenic in Human Hair by Means of Atomic Fluorescence Spectrometry with Hydride Generation Technique

This study describes a simple, rapid and reliable method for simultaneous determination of selenium and arsenic in human hair by means of atomic fluorescence spectrometry combined with a hydride generation technique (HG-AFS). The procedure developed encompasses microwave digestion of a sample in the nitric acid environment only. The interferences caused by nitrous oxides are eliminated by removing a gas from above the digested solution with a stream of argon. The sample is then chemically treated in a flow-through hydride generation system and exposed to measurements in a double-channel atomic fluorescence spectrometer. The method permits determining both analytes in the linear range of 0.5–100µgL^–1 with a detection limit equal to 0.2µgL^–1, as well as with very good repeatability not exceeding 1% for Se and 2% for As. No mutual interferences from either of the analytes in the concentrations ranges matching the hair composition were found. The method was verified in terms of accuracy with the use of a reference material and then applied to the analysis of the natural samples of human hair.     

Copper-catalyzed addition reaction of γ,γ-dialkoxyallylic zirconium species with imines

In the presence of CuCN, reaction of γ,γ-dialkoxyallylic zirconium species 1 with imines proceeded at the γ-position of 1 to give gem-dialkoxyhomoallylic amines 3 in high yield. In this reaction, γ,γ-dialkoxyallylic zirconium species 1 acts as an α,β-unsaturated acyl anion equivalent.     

Speciation of inorganic arsenic by electrochemical hydride generation atomic absorption spectrometry

A simple procedure was developed for the speciation of inorganic arsenic by electrochemical hydride generation atomic absorption spectrometry (EcHG–AAS), without pre-reduction of As(V). Glassy carbon was selected as cathode material in the flow cell. An optimum catholyte concentration for simultaneous generation of arsine from As(III) and As(V) was 0.06 mol l⁻¹ H₂SO₄. Under the optimized conditions, adequate sensitivity and difference in ratio of slopes of the calibration curves for As(III) and As(V) can be achieved at the electrolytic currents of 0.6 and 1 A. The speciation of inorganic arsenic can be performed by controlling the electrolytic currents, and the concentration of As(III) and As(V) in the sample can be calculated according to the equations of absorbance additivity obtained at two selected electrolytic currents. The calibration curves were linear up to 50 ng ml⁻¹ for both As(III) and As(V) at 0.6 and 1 A. The detection limits of the method were 0.2 and 0.5 ng ml⁻¹ for As(III) and As(V) at 0.6 A, respectively. The relative standard deviations were of 2.1% for 20 ng ml⁻¹ As(III) and 2.5% for 20 ng ml⁻¹ As(V). The method was validated by the analysis of human hair certified reference material and successfully applied to speciation of soluble inorganic arsenic in Chinese medicine.     

Comparative analysis of the underground parts ofGentiana species by HPLC with diode-array and mass spectrometric detection

Summary The aim of this work was to compare the chemical composition of the underground parts (roots and rhizomes) ofGentiana cruciata L.,Gentiana pneumonanthe L., andGentiana asclepiadea L.— the three gentians native to Hungary—with that of the widely used stomachicGentiana lutea L., to determine which of the three Hungarian species could be used as a substitute forGentiana lutea in pharmaceutical preparations. The four gentians were compared by means of RPHPLC with diode-array detection (DAD) and electrospray ionization-mass spectrometric detection (ESI-MSD). The quantities of the lead compounds, the secoiridoid-glycosides, in 220 samples of the underground parts of gentians originating from several locations in Hungary, were determined by a more economical RPHPLC-DAD method. The occurrence of the characteristic compounds investigated—bitter principles and xanthones—in the underground parts of the speciesGentiana asclepiadea L. suggest it might be a potential replacement forGentiana lutea L. in pharmaceutical products. Presented at Balaton Symposium '01 on High-Performance Separation Methods, Siófok, Hungary, September 2–4, 2001     

甲烷氧化偶联催化剂La2O3／SrCO3—BaCO3的催化活性与表征

在甲烷氧化偶联制Ｃ２烃的研究中，人们发现碱土金属与稀土金属组成的复合氧化物催化剂具有高的催化活性［１，２］．稀土化合物作为有希望的工业催化剂之一，已受到广泛的关注．一般认为，它们含有的氧空位对活化甲烷的有效氧物种有利．Ｄｅｂｅｙ等在１％Ｓｒ／Ｌａ２Ｏ...