Novel UV‐induced photografting process for preparing poly(tetrafluoroethylene)‐based proton‐conducting membranes

A novel process comprising the UV‐induced photografting of styrene into poly(tetrafluoroethylene) (PTFE) films and subsequent sulfonation has been developed for preparing proton‐conducting membranes. Although under UV irradiation the initial radicals were mainly generated on the surface of the PTFE films by the action of photosensitizers such as xanthone and benzoyl peroxide, the graft chains were readily propagated into the PTFE films. The sulfonation of the grafted films was performed in a chlorosulfonic acid solution. Fourier transform infrared and scanning electron microscopy were used to characterize the grafted and sulfonated membranes. With a view to use in fuel cells, the proton conductivity, water uptake, and mechanical properties of the prepared membranes were measured. Even through the degree of grafting was lower than 10%, the proton conductivity in the thickness direction of the newly prepared membranes could reach a value similar to that of a Nafion membrane. In comparison with γ‐ray radiation grafting, UV‐induced photografting is very simple and safe and is less damaging to the membranes because significant degradation of the PTFE main chains can be avoided. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2624–2637, 2007     

非晶硅薄膜的低温快速晶化及其结构分析

在镀铝的廉价玻璃衬底上高速沉积的非晶硅薄膜在不同的温度下退火10min.退火温度为500℃时,薄膜表面形成了硅铝的混合相,非晶硅薄膜开始呈现了晶化现象 退火温度为550℃时,大部分(约80%)的非晶硅晶化为多晶硅,平均晶粒尺寸为500nm 退火温度为600℃时,几乎所有的非晶硅都转化为多晶硅,其平均晶粒尺寸约为15μm.     

Isothermal crystallization kinetics of poly(3‐hydroxybutyrate)/layered double hydroxide nanocomposites

Poly(3‐hydroxybutyrate) (PHB)/layered double hydroxides (LDHs) nanocomposites were prepared by mixing PHB and poly(ethylene glycol) phosphonates (PEOPAs)‐modified LDH (PMLDH) in chloroform solution. Both X‐ray diffraction data and TEM micrographs of PHB/PMLDH nanocomposites indicate that the PMLDHs are randomly dispersed and exfoliated into the PHB matrix. In this study, the effect of PMLDH on the isothermal crystallization behavior of PHB was investigated using a differential scanning calorimeter (DSC) and polarized optical microscopy. Isothermal crystallization results of PHB/PMLDH nanocomposites show that the addition of 2 wt % PMLDH into PHB induced more heterogeneous nucleation in the crystallization significantly increasing the crystallization rate and reducing their activation energy. By adding more PMLDH into the PHB probably causes more steric hindrance of the diffusion of PHB, reducing the transportation ability of polymer chains during crystallization, thus increasing the activation energy. The correlation among crystallization kinetics, melting behavior and crystalline structure of PHB/PMLDH nanocomposites can also be discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3337–3347, 2006     

Studies on calcium‐containing poly(urethane ether)s

The calcium salt of mono(hydroxyethoxyethyl)phthalate [Ca(HEEP)₂] was synthesized by the reaction of diethylene glycol, phthalic anhydride, and calcium acetate. Calcium‐containing poly(urethane ether)s (PUEs) were synthesized by the reaction of hexamethylene diisocyanate (HMDI) or tolylene 2,4‐diisocyanate (TDI) with a mixture of Ca(HEEP)₂ and poly(ethylene glycol) (PEG₃₀₀ or PEG₄₀₀) with di‐n‐butyltin dilaurate as a catalyst. A series of calcium‐containing PUEs of different compositions were synthesized with Ca(HEEP)₂/PEG₃₀₀ (or PEG₄₀₀)/diisocyanate (HMDI or TDI) molar ratios of 2:2:4, 3:1:4, and 1:3:4 so that the coating properties of the PUEs could be studied. Blank PUEs without calcium‐containing ionic diols were also prepared by the reaction of PEG₃₀₀ or PEG₄₀₀ with HMDI or TDI. The PUEs were well characterized by Fourier transform infrared, ¹H and ¹³C NMR, solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR, viscosity, solubility, and X‐ray diffraction studies. The thermal properties of the polymers were also studied with thermogravimetric analysis and differential scanning calorimetry. The PUEs were applied as top coats on acrylic‐coated leather, and their physicomechanical properties were also studied. The coating properties of PUEs, such as the tensile strength, elongation at break, tear strength, water vapor permeability, flexing endurance, cold crack resistance, abrasion resistance, color fastness, and adhesive strength, were better than the standard values. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2865–2878, 2003     

Latex particles bearing hydrophilic grafted hairs with controlled chain length and functionality synthesized by reversible addition–fragmentation chain transfer

A method is described for synthesizing latex particles with anchored hairs by the grafting of hydrophilic chains, synthesized by reversible addition–fragmentation chain transfer, onto functionalized latex particles. These have the potential to bind biologically active species. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1188–1195, 2003     

Microwave‐improved polymerization of ϵ‐caprolactone initiated by carboxylic acids

The ring‐opening polymerization of ε‐caprolactone (ε‐CL), initiated by carboxylic acids such as benzoic acid and chlorinated acetic acids under microwave irradiation, was investigated; with this method, no metal catalyst was necessary. The product was characterized as poly(ε‐caprolactone) (PCL) by ¹H NMR spectroscopy, Fourier transform infrared spectroscopy, ultraviolet spectroscopy, and gel permeation chromatography. The polymerization was significantly improved under microwave irradiation. The weight‐average molecular weight (M_w) of PCL reached 44,800 g/mol, with a polydispersity index [weight‐average molecular weight/number‐average molecular weight (M_w/M_n)] of 1.6, when a mixture of ε‐CL and benzoic acid (25/1 molar ratio) was irradiated at 680 W for 240 min, whereas PCL with M_w = 12,100 and M_w/M_n = 4.2 was obtained from the same mixture by a conventional heating method at 210 °C for 240 min. A degradation of the resultant PCL was observed during microwave polymerization with chlorinated acetic acids as initiators, and this induced a decrease in M_w of PCL. However, the degradation was hindered by benzoic acid at low concentrations. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 13–21, 2003     

Synthesis and adsorption properties of gold nanoparticles within pores of surface‐functional porous polymer microspheres

Mesoporous polymer microspheres with gold (Au) nanoparticles inside their pores were prepared considering their surface functionality and porosity. The Au/polymer composite microspheres prepared were characterized by transmission electron microscope (TEM), X‐ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) techniques. The results showed that the adsorption of Au nanoparticles could be increased by imparting the pore structure and surface‐functional groups into the supporting polymer microspheres (in this study, poly (ethylene glycol dimethacrylate‐co‐acrylonitrile) and poly (EGDMA‐co‐AN) system). Above all, from this study, it was established that the porosity of the polymer microspheres is the most important factor that determines the distribution and adsorption amount of face‐centered cubic (fcc) Au nanoparticles in the final products. Our study showed that the continuous adsorption of Au nanoparticles with the aid of the large surface area and surface interaction sites formed more favorably the Au/polymer composite microspheres. The BET measurements of Au/poly(EGDMA‐co‐AN) composite microspheres reveals that the adsorption of Au nanoparticles into the pores kept the pore structure intact and made it more porous. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5627–5635, 2004     

Temperature‐modulated differential scanning calorimetry studies on the origin of double melting peaks in isothermally melt‐crystallized poly(L‐lactic acid)

In this work, the melting behaviors of nonisothermally and isothermally melt‐crystallized poly(L ‐lactic acid) (PLLA) from the melt were investigated with differential scanning calorimetry (DSC) and temperature‐modulated differential scanning calorimetry (TMDSC). The isothermal melt crystallizations of PLLA at a temperature in the range of 100–110 °C for 120 min or at 110 °C for a time in the range of 10–180 min appeared to exhibit double melting peaks in the DSC heating curves of 10 °C/min. TMDSC analysis revealed that the melting–recrystallization mechanism dominated the formation of the double melting peaks in PLLA samples following melt crystallizations at 110 °C for a shorter time (≤30 min) or at a lower temperature (100, 103, or 105 °C) for 120 min, whereas the double lamellar thickness model dominated the formation of the double melting peaks in those PLLA samples crystallized at a higher temperature (108 or 110 °C) for 120 min or at 110 °C for a longer time (≥45 min). © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 466–474, 2007     

On‐line Determination of Particle Size Distributions in Flowing Dispersions

Emulsions are of great importance to industry. They are involved in many engineering operations, including chemical reactions, extraction, emulsification and suspension polymerization, etc. However, an important problem for these processes is how to control the size distribution of the dispersed phase. Indeed, off‐line analysis of the emulsion may generate uncertainties due to sampling and dilution of the product, which are likely to change the dispersion state and physico‐chemical properties. In this work, an on‐line optical method is proposed to characterize dispersed media in real flowing conditions. This method is based on the time‐analysis of back‐scattered light fluctuations. The present paper deals with the development of this method and its application to dispersions of alumina in water. The results obtained with the on‐line optical method are compared with those acquired by classical laser light scattering and microscopy.     

Kinetics and mechanism of the formation of poly[(1,1,3,3-tetramethyldisiloxanyl)ethylene] and poly(methyldecylsiloxane) by hydrosilylation

The kinetics of the formation of poly(carbosiloxane), as well as of alkyl-substituted poly(siloxane), by Karstedt's catalyst catalyzed hydrosilylation were investigated. Linear poly(carbosiloxane), poly[(1,1,3,3-tetramethyldisiloxanyl)ethylene], (PTMDSE), was obtained by hydrosilylation of 1,3-divinyltetramethyldisiloxane (DVTMDS) and 1,1,3,3-tetramethyldisiloxane (TMDS), while alkyl-substituted poly(siloxane), poly(methyldecylsiloxane), (PMDS), was synthesized by hydrosilylation of poly(methylhydrosiloxane) (PMHS) and 1-decene. To investigate the kinetics of PTMDSE formation, two series of experiments were performed at reaction temperatures ranging from 25 to 56 °C and with catalyst concentrations ranging from 7.0 × 10⁻⁶ to 3.1 × 10⁻⁵ mol Pt/mol CHCH₂. A series of experiments was performed at reaction temperatures ranging from 28 to 48 °C, with catalyst concentrations of 7.0 ×10⁻⁶ mol of Pt per mol of CHCH₂, when kinetics of PMDS formation was investigated. All reactions were carried out in bulk, with equimolar amounts of the reacting Si H and CHCH₂ groups. The course of the reactions was monitored by following the disappearance of the Si H bands using quantitative infrared spectroscopy. The results obtained showed typical first order kinetics for the PTMDSE formation, consistent with the proposed reaction mechanism. In the case of PMDS an induction period occurred at lower reaction temperatures, but disappeared at 44 °C and the rate of Si H conversion also started to follow the first-order kinetics. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2246–2258, 2007