Characteristics of selective oxidation during the fabrication of vertical cavity surface emitting laser

Taking into account oxidation temperature, N₂ carrier gas flow, and the geometry of the mesa structures this paper investigates the characteristics of selective oxidation during the fabrication of the vertical cavity surface emitting laser (VCSEL) in detail. Results show that the selective oxidation follows a law which differs from any reported in the literature. Below 435℃ selective oxidation of Al_0.98Ga_0.02As follows a linear growth law for the two mesa structures employed in VCSEL. Above 435℃ approximately increasing parabolic growth is found, which is influenced by the geometry of the mesa structures. Theoretical analysis on the difference between the two structures for the initial oxidation has been performed, which demonstrates that the geometry of the mesa structures does influence on the growth rate of oxide at higher temperatures.     

场发射栅孔阵列的制备

 采用硅的局部氧化技术以及湿法刻蚀技术,利用2.6 μm的光刻掩模板在n型硅片上形成了栅极孔径为1 μm的场发射阴极的栅极空腔阵列,实现了用大阵点尺寸的栅极掩模板制备较小尺寸栅孔阵列。硅的湿法刻蚀溶液采用各向同性的硝酸和氢氟酸混合溶液,刻蚀后空腔的深度和宽度均随刻蚀时间线性增加。同时,由于刻蚀溶液具有较高的Si/SiO₂ 刻蚀选择比,栅极孔径随刻蚀时间增大的速度远低于深度和宽度增大的速度,栅极孔径主要取决于掩模的尺寸和氧化层的厚度。通过选择掩模板的尺寸以及氧化层的厚度,采用局部氧化技术和湿法刻蚀技术能够制备出微米或亚微米的场发射阴极的栅极空腔阵列。     

Mechanism of heterogeneous mercury oxidation by HCl on V2O5(001) surface

The selective catalytic reduction (SCR) system for NO_X removal in coal-fired power plants has a promoting effect on the oxidation and removal of elemental mercury. In this study, basic mechanism of mercury oxidation by V₂O₅-based SCR catalyst is investigated via density functional theory method and the periodic slab models. Calculations are conducted to determine the adsorption energies and geometries of Hg⁰, HgCl, HgCl₂ and HCl on V₂O₅(001) surface, and to reveal the energy profile of oxidation reaction and the structures of relative transition states and intermediates. The results indicate that HCl can significantly promote Hg⁰ oxidation on V₂O₅(001) surface, by forming an intermediate HgCl-surface which is important for Hg⁰ oxidation. The Hg⁰ oxidation goes through Hg⁰ → HgCl → HgCl₂, and the two stages of the reaction follow Eley–Rideal mechanism and Langmuir-Hinshelwood mechanism, respectively. The formation of HgCl₂ is the rate-determining step due to its high energy barrier. Three detailed reaction pathways are obtained, and the related energy profiles and structures are analyzed in detail. The Hg⁰ oxidation reaction can take place through all three pathways even if differences exist in each other, while pathways I and II have relatively low energy barriers.     

热氧化法制备ZnO纳米晶体、纳米线

以高纯Zn块为源材料,通过热氧化法制备了纳米ZnO薄膜。在950℃的温度和一定的压力条件下,通过改变生长时间,分别制备了ZnO纳米晶体、纳米纤维和纳米线。应用扫描电镜观察发现,在恒温生长条件下,纳米ZnO具有定向生长的趋势。随生长时间的延长,纳米晶体定向生长为纳米纤维,最后生长为超长的纳米线。     

ZnO/MoO3 mixed oxide nanotube: A highly efficient and stable catalyst for degradation of dye by air under room conditions

As a continuation of our work to develop catalysts with high activity for catalytic air wet oxidation process under mild conditions, degradation of wastewater containing 0.3 g/L Safranin-T (ST) by air oxidation over ZnO/MoO₃ nanotube catalyst was studied. It was found the decolorization efficiency and the chemical oxygen demand (COD) removal of ST reached above 98% and 95%, respectively, within 18 min at room temperature and atmospheric pressure. And the organic pollutants were totally mineralized to simple inorganic species such as HCO₃⁻, Cl⁻ and NO₃⁻, while the total organic carbon (TOC) decreased 99.3%. The structure and morphology of the catalyst after ten cycling runs showed that the catalyst was stable under such operating condition and the leaching test showed negligible leaching effect. This ZnO/MoO₃ nanotube is proved to be an active and stable heterogeneous catalyst in CWAO of ST under extremely mild conditions.     

Aligned synthesis of multi-walled carbon nanotubes with high purity by aerosol assisted chemical vapor deposition: Effect of water vapor

Aligned multi-walled carbon nanotubes (MWCNTs) with high purity and bulk yield were achieved on a silicon substrate by an aerosol-assisted chemical vapor deposition. The introduction of specific amounts of water vapor played a key role in in situ controlling the purity and surface defects of the nanotubes. The morphology, surface quality and structure of MWCNTs were characterized by secondary and backscattered electron imaging in a field emission scanning electron microscope (FESEM) and transmission electron microscope (TEM). Crystallinity and defects of the MWCNTs’ were investigated by high-resolution transmission electron microscopy (HRTEM) and Raman spectroscopy. In this work, water vapor was found to provide a weak oxidative environment, which enhanced and purified the MWCNTs’ growth. However, excessive water vapor would inhibit the MWCNTs growth with a poor surface quality. In addition, it has been found that the surface morphology of the CNTs can be modified intentionally through producing some surface defects by tuning the amount of the water vapor, which may offer more nucleation sites on the chemically inert CNT surface for various applications such as catalyst support.     

Influence of ultrasonication and Fenton oxidation pre-treatment on rheological characteristics of wastewater sludge

The effect of ultrasonication and Fenton oxidation as physico-chemical pre-treatment processes on the change of rheology of wastewater sludge was investigated in this study. Pre-treated and raw sludges displayed non-Newtonian rheological behaviour with shear thinning as well as thixotropic properties for total solids ranging from 10 g/L to 40 g/L. The rheological models, namely, Bingham plastic, Casson law, NCA/CMA Casson, IPC Paste, and power law were also studied to characterize flow of raw and pre-treated sludges. Among all rheological models, the power law was more prominent in describing the rheology of the sludges. Pre-treatment processes resulted in a decrease in pseudoplasticity of sludge due to the decrease in consistency index K varying from 42.4 to 1188, 25.6 to 620.4 and 52.5 to 317.9; and increase in flow behaviour index n changing from 0.5 to 0.35, 0.62 to 0.55 and 0.63 to 0.58, for RS, UlS and FS, respectively at solids concentration 10–40 g/L. The correlation between improvement of biodegradability and dewaterability, decrease in viscosity, and change in particle size as a function of sludge pre-treatment process was also investigated. Fenton oxidation facilitated sludge filterability resulting in capillary suction time values which were approximately 50% of the raw sludges, whereas ultrasonication with high input energy deteriorated the filterability. Biodegradability was also enhanced by the pre-treatment processes and the maximum value was obtained (64%, 77% and 73% for raw, ultrasonicated and Fenton oxidized sludges, respectively) at total solids concentration of 25 g/L. Hence, pre-treatment of wastewater sludge modified the rheological properties so that: (1) the flowability of sludge was improved for transport through the treatment train (via pipes and pumps); (2) the dewaterability of wastewater sludge was enhanced for eventual disposal and; (3) the assimilation of nutrients by microorganisms for further value-addition was increased.     

Nb掺杂对γ-TiAl抗氧化能力影响的第一性原理研究

添加Nb被证实是提高TiAl合金抗氧化能力最有效的途径之一,但对于其机理仍然存在一些相互矛盾的解释.运用第一性原理方法对γ-TiAl氧化过程中存在的几种重要点缺陷杂质进行了系统的研究.在确定杂质的稳定结构基础之上,研究发现：γ-TiAl中Nb掺杂的形成能随着含量的增加而升高,导致γ-TiAl相的稳定性降低,对抗氧化性能造成不利影响;而间隙O和Ti空位的形成能随Nb掺杂量的增加而显著升高,因此Nb能有效地降低氧扩散及空位缺陷的进入,从而提高γ-TiAl的抗氧化性能;Nb掺杂对降低杂质含量的作用存在明显的局域特性,是一种近程作用,因此Nb在γ-TiAl中的作用与其含量和分布有关. 关键词： γ-TiAl 高温氧化 Nb掺杂 形成能     

大面积α-Fe2O3纳米线及纳米带阵列的制备研究

以铁箔为原材料和基片,通过控制热氧化过程中的宏观实验条件(载气流量及其组分、压强、温度分布和反应时间等),实现了α-Fe₂O₃一维纳米结构的可控生长,获得了大面积(10mm×10mm)、单分散性好、沿［110］方向生长的α-Fe₂O₃纳米带或纳米线阵列. 对不同宏观实验条件下所制备的样品进行形貌和晶格结构表征和分析,认为热氧化过程中α-Fe₂O₃一维纳米结构的生长遵循类似气- 关键词： 2O₃')" href="#">α-Fe₂O₃ 一维纳米结构 热氧化法