Physicochemical aspects of microbial adhesion — Influence of antibody adsorption on the deposition ofStreptococcus sobrinus in a parallel-plate flow chamber

Deposition of the oral bacteriumStreptococcus sobrinus HG977 onto glass (water contact angle 0°) and onto FEP-Teflon (fluoroethylenepropylene; water contact angle 110°) was studied in a parallel-plate flow chamber in the presence and absence of polyclonal antibodies (pAb) and monoclonal antibodies (mAbs) adsorbed onto the cells. The zeta potentials of the bacteria ranged from −7.1 to −8.5 mV at pH 6.8 and were not affected by the presence of pAb or mAbs. Hydrophobicity (by water contact angles) increased from 30° (no antibodies) to 88° in the presence of pAb adsorbed onto the bacterial cell surface. The untreatedS. sobrinus had a greater tendency to adhere to glass (44.5 × 10⁶ cm⁻²) than to FEP-Teflon (18.3 × 10⁶ cm⁻²), in accordance with thermodynamic modelling. After preincubation ofS. sobrinus with pAb, its clear preference for adhesion to glass disappeared as expected from its increased hydrophobicity. Although forS. sobrinus preincubated with OMVU10 no difference was found in hydrophobicity in comparison to the untreated bacteria, the number of bacteria adhering to glass decreased to 10.2 ¢ 10⁶ cm⁻². Formation of bacterial aggregates was found whenS. sobrinus, preincubated with pAb or OMVU10, adhered to glass and FEP. This was also observed when untreated bacteria adhered to glass coated with OMVU10, or to FEP coaled with OMVU10 or pAb. Adhesion in these experiments is therefore thought to occur via near-neighbour collection induced by the presence of pAb or mAbs. Low numbers of bacteria were removed from glass after draining the flow cell, whereas high numbers of untreated bacteria and bacteria preincubated with OMVU10 were removed from FEP.S. sobrinus cells preincubated with pAb were not removed but piled up. It was concluded that the adhesion of untreatedS. sobrinus andS. sobrinus preincubated with pAb is in accordance with thermodynamic modelling, based on the overall wettability of the cell surfaces, whereas the adhesion ofS. sobrinus preincubated with OMVU10 may be through localized interactions, not expressed in overall surface properties.     

(ClAlNH)n簇合物的结构与稳定性

用量子化学从头算方法（HF／6－31G）和密度泛函理论（DFT）的B3LYP方法，以6－31G标准基组加一个极化函数，对（ClAlNH)n(n=1-10)簇合物的几何构型，电子结构和红外光谱进行了优化，并讨论了聚合反应（ClAlNH)m→(ClAlNH)n的热力学效应，结果表明，（ClAlNH)n系列簇合物的基态稳定结构为Cs(n=1),D2h(n=2),D3h(n=3),Td(n=4),Cs(n=5),D3d(n=6),Cs(n=7),S4(n=8),D3h(n=9),C2h(n=10,n=2,4,6,8,10等偶数对应的（ClAlNH)n簇化合物的结构比n等于奇数量更稳定。     

The effect of the exchangeable metallic cation on the colloid properties of laponite treated with acridine orangea spectrophotometric study

The adsorption of the cationic dye acridine orange (AO) by different monoionic laponites leads to changes in the colloid properties of this synthetic mineral in aqueous solutions. The organic cation is adsorbed by the mechanism of cation exchange. Small amounts of adsorbed dye keep the clay in a peptized state with all metallic cations. Greater amounts of AO result in the neutralization of the electric charge of the clay, and its flocculation. In excess AO the charge of the clay platelets becomes positive and the clay is peptized. The colloid properties are studied by absorbance curves in which the absorbance is described as a function of the degree of saturation with constant clay concentrations or with constant dye concentrations. In the absorbance curves three regions can be identified. The transition between the first and second or the second and third regions depend on the exchangeable metallic cation initially present in the clay. The spectrophotometric method is useful in identifying the presence of tactoids and flocculation mechanism, whether it results in card-house or in book-house flocs.     

Effect of Inorganic Ions on Oleate Adsorption at a Nigerian Hematite–Water Interface

Using “pure” natural hematite selected from a high silica Nigerian hematitic ore, oleate adsorption densities at the hematite–water interface were determined in the presence of various inorganic ions (anions and cations) of different charges and at varying concentrations. Adsorption density was determined using electrical conductivity measurements. The specific surface area of the hematite particles was determined using the method of adsorption of paranitrophenol in aqueous solution. Inorganic ions in solution depressed oleate adsorption at the aqueous hematite surface. The charge of the ion proved to be the dominant factor determining the depression of oleate adsorption. Ionic strength also was an influence, up to a limiting value at which monolayer oleate coverage of the hematite surface occurred. The inorganic ions in solution are considered to function through nonspecific adsorption in the diffuse region of the electric double layer.     

A Branched Pore Model Analysis for the Adsorption of Acid Dyes on Activated Carbon

A new branched-pore adsorption model has been developed using an external mass transfer coefficient, K _f, an effective diffusivity, D _eff, a lumped micropore diffusion rate parameter, K _b, and the fraction of macropores, f, to describe sorption kinetic data from initial adsorbent-adsorbate contact to the long-term adsorption phase. This model has been applied to an environmental pollution problem—the removal of two dyes, Acid Blue 80 (AB80) and Acid Red 114 (AR114), by sorption on activated carbon. A computer program has been used to generate theoretical concentration-time curves and the four mass transfer kinetic parameters adjusted so that the model achieves a close fit to the experimental data. The best fit values of the parameters have been determined for different initial dye concentrations and carbon masses. Since the model is specifically applicable to fixed constant values of these four parameters, a further and key application of this project is to see if single constant values of these parameters can be used to describe all the experimental concentration-time decay curves for one dye-carbon system.The error analysis and best fit approach to modeling the decay curves for both dye systems show that the correlation between experimental and theoretical data is good for the fixed values of the four fitted parameters. A significantly better fit of the model predictions is obtained when K _f, K _b and f are maintained constant but D _eff is varied. This indicates that the surface diffusivity may vary as a function of surface coverage.     

Adsorptive passivation of iron by organic acid anions

Studies on the iron passivation by organic acid anions in aqueous solutions are briefly reviewed. It is shown that the passivation can be caused only by their adsorption, retarding both the iron dissolution and the formation of oxide films. Earlier, it had been believed that oxide films play a dominant role in the iron passivation in neutral solutions. The recent viewpoint is that such nonoxide iron passivation can occur in solutions of salts of not only aromatic amino acids (sodium phenylantranilate and its substitutes), but other carboxylic acids as well. An important role of chemisorption and hydrophobic properties of anions for the formation of adsorption passive films is emphasized. New possibilities for inhibitor protection of iron against corrosion, which is based on adsorptive passivation, are pointed out.Translated from Elektrokhimiya, Vol. 40, No. 12, 2004, pp. 1503–1507.Original Russian Text Copyright © 2004 by Kuznetsov.     

The Effect of the Nature and Structure of Adsorbents on Interaction with Ibuprofen

The interaction of ibuprofen [2-(4-isobutylphenyl)propionic acid] with the surface of carbon and oxide adsorbents was investigated. The significant role of wide pores during the adsorption of ibuprofen on carbon adsorbents in the presence of protein molecules was demonstrated. At low concentrations ibuprofen is adsorbed on the surface of hydrophilic and hydrophobic adsorbents in the form of a monomer, but the contribution from the adsorbed dimer increases with increase in its concentration.     

Optimization of the Conditions for the Cr (III) Adsorption on Activated Carbon

In order to understand the patterns of the adsorption equilibrium of Cr (III) on activated carbon, the adsorption process was studied by two different ways: classical batch experiments on commercial Norit and Merck activated carbons and their oxidized forms in a wide range of pHs; and extended time-based tests at the same pH values on the same adsorbents. This approach allowed us to understand the role of texture, chemical carbon surface functionality and experimental conditions (initial pH of the solution, contact time and adsorbate/adsorbent ratio) on the effectiveness of Cr (III) removal. The adsorption process of Cr (III) at (24 ± 1^∘C) on Merck and Norit activated carbons and their oxidized forms were studied at pH values between 1.5 and 5 (either adjusted or buffered). Chromium concentration was fixed at 200 ppm. The carbon loading ranged from 1.2 to 20 g/l. The carbon/Cr (III) solution contact time was varied from 0.5–1 month to 5 months, to ensure that the saturation of the carbon level was reached. According to the data obtained, the presence of carboxylic groups on carbon surface seems to enhance Cr (III) uptake at initial pH of the solution in the range between 2 and 4. Depending on the nature of the adsorbent surface chemistry, the contact time to reach equilibrium may range from 3 to 5 months. There is an optimum carbon loading which limits the Cr (III) uptake/removal at given pH value. In order to understand the adsorption process, an ion exchange, surface complex and surface precipitation were considered. This paper was presented in the 5th Brazilian Meeting on Adsorption, held at Natal, Brazil, 18-21 July, 2004.     

Characterization of Titania/Silica Gel by Means of Low-Pressure Nitrogen Adsorption

Adsorbents synthesized by grafting of titania onto mesoporous silica gel surfaces at different temperatures were studied by means of nitrogen adsorption–desorption and water desorption. The pore size distribution f(R_p) of titania/silica gel depends on the titania concentration (C_TiO2) and the temperature of titania synthesis. Nonuniformity of TiO₂ phase is maximal at a low C_TiO2 value (3.2 wt.% anatase deposited at 473 K), and two peaks of the fractal dimension distribution f(D) are observed at such a concentration of titania, but at larger C_TiO2 values, only one f(D) peak is seen. More ordered filling of pores and adsorption sites by nitrogen, reflecting in the shape of adsorption energy distributions f(E) at different pressures of adsorbate, is observed for adsorbent with titania (rutile+anatase) grafted on silica gel at a higher temperature (673 K).     

大孔吸附树脂对邻甲酚的吸附行为研究

研究了大孔吸附树脂NDA—909吸附水溶液中邻甲酚的热力学特征，并与Amberlite XAD—4树脂进行了比较．通过吸附动力学实验，初步探讨了初始温度对吸附过程的影响。结果表明，NDA—909对邻甲酚的吸附符合Freundlich经验公式，表现为放热的物理吸附过程．此外吸附速率受颗粒内扩散和其它类型扩散的共同控制。