Roles of SiH4 and SiF4 in growth and structural changes of poly-Si films

The structural properties of polycrystalline silicon films, prepared by plasma enhanced chemical vapor deposition system, with different flow rates of SiH₄/SiF₄ mixtures at 300 °C were investigated. This study indicates that the low hydrogen coverage on the growing surface, under optimum fluorine radicals, will be leaded to an improvement of crystallized area as compared with case of high hydrogen coverage surface. Moreover, the studies of the role of SiH₄ and SiF₄ radicals show that the SiH₄ radicals are important in the nucleation and growth of grains. However, SiF₄ radicals are effective in the structural change of grain boundaries regions and by this way, in the present system, establish the growth of grains under the dominant 〈1 1 0〉 direction. The stress investigation indicates that addition of high flow rate of SiF₄ in amorphous film, results in the nearly stress free films. Finally, we found that the changes in g-value reflect the changes in the intrinsic compressive and tensile stress in the both polycrystalline and amorphous silicon films.     

HgCl2/I2复合催化剂协同催化合成异丙醇钇的研究

以金属钇和异丙醇为原料，以HgCl2/I2为复合催化剂，通过对金属钇的机械加工以增加其比表面，并将异丙醇脱水使其含水量降低至0．05％，体系在82℃回流5h，经过滤、减压蒸馏，得到了白色海绵状异丙醇钇，其产率高达83％，合成时间比文献报道的缩短了19h，产率提高了8％。文章确定了催化剂的最佳用量为20gY加入60mg HgCl2/I2，研究了合成产率与HgCl2/I2催化剂和HgCl2催化剂的依赖关系及异丙醇中含水量对合成产率的影响，并对HgCl2/I2的催化作用机理进行了初步探讨。     

Numerical solutions of the shallow water equations with discontinuous bed topography

A simple scheme is developed for treatment of vertical bed topography in shallow water flows. The effect of the vertical step on flows is modelled with the shallow water equations including local energy loss terms. The bed elevation is denoted with z_b^‐ for the left and z_b⁺ for the right values at each grid point, hence exactly representing a discontinuity in the bed topography. The surface gradient method (SGM) is generalized to reconstruct water depths at cell interfaces involving a vertical step so that the fluxes at the cell interfaces can accurately be calculated with a Riemann solver. The scheme is verified by predicting a surge crossing a step, a tidal flow over a step and dam‐break flows on wet/dry beds. The results have shown good agreements compared with analytical solutions and available experimental data. The scheme is efficient, robust, and may be used for practical flow calculations. Copyright © 2002 John Wiley & Sons, Ltd.     

SEPARATING SCN~- FROM DESULPHURIZATION WASTE SOLUTION OF COCKING PLANT BY D241 RESIN

1. INTRODUCTION In the process of coking plant, about 30%~35% sulfur is transformed to H2S and some other sulfide, which form impurity in coal gas together with NH3 and HCN. Only 0.1% H2S containing in air can lead to die, so it is very important to carry on desulphurization and decyanation with coal gas [1~3]. Currently desulphurization and decyanation craft technique have Dry Oxidation Technology, Wet Oxidation Technology and Liquid Absorption Technology [2] three main kinds. The…     

Spray Freeze-drying – The Process of Choice for Low Water Soluble Drugs?

Most of the novel highly potent drugs, developed on the basis of modern molecular medicine, taking into account cell surface recognition techniques, show poor water solubility. A chemical modification of the drug substance enhancing the solubility often decreases the pharmacological activity. Thus, as an alternative an increase of the solubility can be obtained by the reduction of the size of the drug particles. Unfortunately, it is often difficult to obtain micro or nanosized drug particles by classical or more advanced crystallization using supercritical gases or by milling techniques. In addition, nanosized particles are often not physically stable and need to be stabilized in an appropriate matrix. Thus, it may be of interest to manufacture directly nanosized drug particles stabilized in an inert hydrophilic matrix, i.e. nanostructured and nanocomposite systems. Solid solutions and solid dispersions represent nanostructured and nanocomposite systems. In this context, the use of the vacuum-fluidized-bed technique for the spray-drying of a low water soluble drug cosolubilized with a hydrophilic excipient in a polar organic solvent is discussed. In order to avoid the use of organic solvents, a special spray-freeze-drying technique working at atmospheric pressure is presented. This process is very suitable for temperature and otherwise sensitive drugs such as pharmaproteins.     

高温水蓄冷空调的原理和理论分析

介绍了一种新型高温水蓄冷空调方案的原理井进行了理论分析。它可利用高至３８℃水的显热或其它材料的相变潜热来蓄冷空调．分析了完全不掺混系统的性能与过冷水流率的关系；给出了完全掺混系统非稳态循环的性能变化；数值计算并讨论了蓄冷水部分掺混系统的温度分层和动态特性、为高温水蓄冷空调系统的设计和运行提供了理论指导．     

Monte Carlo study of interfacial silicon suboxide layers and oxidation kinetics

A simple simulation scheme that simultaneously describes the growth kinetics of SiO₂ films at the nanometer scale and the SiO_x/Si interface dynamics (its extent, and spatial/temporal evolution) is presented. The simulation successfully applies to experimental data in the region above and below 10 nm, reproduces the Deal and Grove linear-parabolic law and the oxide growth rate enhancement in the very thin film regime (the so-called anomalous region). According to the simulation, the oxidation is governed mainly by two processes: (a) the formation of a transition suboxide layer and (b) its subsequent drift towards the silicon bulk. We found that it is the superposition of these two processes that produces the crossover from the anomalous oxidation region behavior to the linear-parabolic law.     

PVK∶DBVP掺杂体系的能量转移及发光性质的研究

研究了不同比例的PVK与齐聚PPV衍生物DBVP掺杂体系的能量转移和发光特性.通过对PVK,DBVP及PVK:DBVP掺杂体系的UV-vis,PL和PLE光谱的研究,分析了PVK与DBVP之间的能量转移过程.利用PVK在体系中类似于溶剂的分散作用,制备了结构为ITO/PEDOT/PVK:DBVP/LiF/Al的电致发光器件,研究了掺杂体系的电致发光性能.结果表明,在掺杂体系的光致发光和电致发光中,PVK的发射被有效地抑制,PVK与DBVP之间发生了非常有效的能量转移,通过调节PVK与DBVP的比例,可以获得蓝色和绿色发光,同时可以改善器件的发光性能,当PVK与DBVP的重量比为1∶2时,器件的绿色发光效率达到1·06cd/A,此时发光亮度为52cd/m2.     

水反常热膨胀特性的简易实验

通过改变带细玻璃管的烧瓶中水的温度导致水位变化来粗略演示水的收缩情况.为较准确测定水最大密度时的温度,将2个温度计放在水下较浅处和较深处,分别测量当温度经由4℃升高时和由4℃降低时两温度计的示数,进而验证水的反常热膨胀特性.     

Simple, expedient methods for the determination of water and electrolyte contents of cellulose solvent systems

The concentrations of water, W, and electrolytes present in solutions of LiCl in N,N-dimethylacetamide, LiCl/DMAc, and of tetrabutylammonium fluoride. x-hydrate in DMSO, TBAF.xW/DMSO can be accurately and expediently determined by three independent methods, UV–vis, FTIR and EMF measurement. The first relies on the use of solvatochromic probes whose spectra are sensitive to solution composition. It is applicable to W/LiCl/DMAc solutions but not to TBAF.xW/DMSO, because the charge-transfer complex bands of the probes are suppressed by strong interactions with the latter electrolyte. Integration of ν_OH band of water may be employed in order to determine [W], hence [electrolyte] by weight difference. EMF measurement uses ion-selective electrodes in order to determine [electrolyte], hence [W] by weight difference. Results of the latter method were in excellent agreement with those of FTIR. The reason for the failure of Karl Fischer titration is addressed, and the relevance of the results obtained to functionalization of cellulose under homogenous solution conditions is briefly commented on.