Facile one‐pot method of initiator fixation for surface‐initiated atom transfer radical polymerization on carbon hard spheres

An efficient and novel one‐pot process is developed to immobilize the atom transfer radical polymerization (ATRP) initiators onto the surface of fully pyrolyzed carbon hard spheres (CHSs) via a radical trapping process from the in situ thermal decomposition of bis(bromomethylbenzoyl)peroxide. The CHSs do not require any additional preparative treatment prior to the initiator immobilization. Styrene and methyl methacrylate are polymerized onto initiator‐immobilized CHSs by surface‐initiated atomic transfer radical polymerization (SI‐ATRP). Samples are characterized using Fourier transform infrared, thermogravimetric analysis, scanning electron microscopy, and transmission electron microscopy. These methods of characterization confirmed that all the CHSs are coated with a uniform layer of grafted polymer. This efficient, one‐pot immobilization of ATRP‐initiators represents an exceptionally simple route for the rapid preparation of various polymer‐coated carbon‐based nanomaterials using SI‐ATRP. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3314–3322     

Halocarbons in Antarctic Surface Waters

Abstract

Surface water samples taken during the 1988–89, 1989–90 and 1990–91 Italian expeditions were analyzed for the presence of carbon tetrachloride, trichloroethylene and tetrachloroethylene. The sample analysis was carried out by solvent extraction and capillary GC-ECD-MS determination. The above-mentioned halocarbons were at ng/l level in all water samples investigated.     

Sampling and Analysis of Odorous Compounds in Water Treatment Plants

Abstract

The following analytical method has been used to identify some odorous compounds in the air of the water treatment plant Werdholzli, Zurich: sampling of contaminated air with the help of activated carbon, desorption by the solvents carbon disulphide and methylene chloride, separation of the carbon disulfide extract into a polar and a nonpolar fraction by adsorption column chromatography on silica. Hereafter gaschromatographic analysis of the polar fraction on glass capillary column (Ucon HB 5100); detection and identification were achieved by flame ionisation, thermoionic nitrogen selective detector and computerized mass spectrometry (Finnigan 3200 F, data system 6110).

The results show the presence of sulfur compounds: thiophenes, thiazoles; nitrogen compounds: pyrazines; oxygen compounds: phenols, alcohols and some unsatured hydrocarbons. The malodorous compounds were sulfur and nitrogen compounds in the range of 0.01-0.1 ppm.     

HCSE method for detection of small carbon–carbon couplings and their signs,comparison with SLAP pulse sequence

Performance of homonuclear coupling sign edited (HCSE) experiment applied to detection of signed carbon–carbon couplings is discussed using a set of already measured samples of nine monosubstituted benzenes. It is shown that coupling sign detection is insensitive to the settings of carbon–carbon polarization transfer delays. The HCSE spectra of ten from the total of 43 measured carbon–carbon couplings were considerably influenced by relaxations and proton–proton strong couplings. These effects are quantitatively discussed. The results of HCSE and SLAP experiments are compared. It is shown that the two methods may complement each other in detection of signed carbon–carbon couplings. Copyright © 2013 John Wiley & Sons, Ltd.     

Influence of the Interaction between Two Neighboring Periodically Curved Fibers on the Stress Distribution in a Composite Material

A method is developed for a stress analysis in an infinite elastic body containing two neighboring periodically cophasaly curved fibers located along two parallel lines. The stress distribution is studied when the body is loaded at infinity by uniformly distributed normal forces in the fiber direction. The investigation is carried out within the framework of a piecewise homogeneous body model with the use of exact three-dimensional equations of elasticity theory. Numerical results related to the stress distribution considered and the influence of interaction between the fibers on this distribution are given.     

Fracture Model for a Thin Layer of a Fibrous Composite

A model for a flat isolated layer of a unidirectional fibrous composite with a regular structure is constructed to investigate the possible variants of its failure development. An integrodifferential equation for determining the forces in fibers is obtained. Primary attention is focused on examining the failure process after the rupture of one fiber. This causes a drastic redistribution of stresses, which can lead to a failure of adjacent fibers owing to the increased load on them, to an interfacial shear fracture, and to the matrix cracking. It is shown that the development of layer failure is determined by the strength of fibers, the crack resistance of the matrix in axial tension and transverse shear, and also by the adhesion strength of the matrix-fiber interface. The sufficient conditions of applicability of the brittle fracture model are formulated.     

The Effect of Adhesion Interaction on the Mechanical Properties of Thermoplastic Basalt Plastics

The effect of temperature, adhesion time, and surface treatment of a reinforcing filler on the mechanical properties of thermoplastic basalt plastics based on a high-density polyethylene and a copolymer of 1,3,5-trioxane with 1,3-dioxolan is investigated. An extreme dependence for the adhesive strength in a thermoplastic-basalt fiber system is established and its effect on the mechanical properties of basalt plastics and the influence of the adhesion contact time on the adhesive strength in the system are clarified. The surface modification of basalt fibers in acidic and alkaline media intensifies the adhesion of thermoplastics to them owing to a more developed surface of the reinforcing fibers after etching. It is found that the treatment in the acidic medium is more efficient and considerably improves the mechanical properties of basalt plastics.     

多孔细径微肋管内CO2流动蒸发换热特性的研究

对亚临界二氧化碳在带有微肋的微细通道内的蒸发换热特性进行了实验研究.实验段为长0.6 m,内径1.7 mm的八孔带0.16 mm高微肋的铝制扁管.实验中参数的变化为:蒸发温度1～15 ℃,质量流速100～300 kg/m2s,热流密度1.67～8.33 kW/m2,干度0.1～0.9.实验结果表明,二氧化碳在带有微肋的微细通道中的蒸发换热系数高于其在光滑微细通道内的换热.二氧化碳的流动蒸发换热系数主要受热流密度和蒸发温度的影响,基本上是换热系数随热流密度及蒸发温度的增加而增加,但同时临界干度前移及滞后,而质量流速对换热系数的影响较弱;压力损失随质量流速和热流密度的增加以及蒸发温度的降低而增加.     

Microencapsulation of TiO2 Nanoparticles with Polymer by Rapid Expansion of Supercritical Solution

A novel preparation method is reported for the microencapsulation of TiO₂ nanoparticles by rapid expansion of supercritical solution with a nonsolvent. A suspension of TiO₂ nanoparticles in carbon dioxide containing a cosolvent and dissolved polymer is sprayed through a nozzle to atmospheric pressure. After rapid expansion, polymer microspheres were obtained. The microspheres do not tend to agglomerate, since the pure cosolvent is a nonsolvent for the polymer. The structure and morphology of microspheres were investigated by SEM, TEM and XRD. The obtained polymer microspheres are microcapsules of TiO₂ nanoparticles. The mean particle diameter and particle size distribution of microcapsules, could be controlled by changing the polymer concentration, pre-expansion pressure, temperature and injection distance. The polymer feed compositions are more effective than other factors on the control of particle size.     

碳纳米管锁模双包层光纤激光器的实验研究

本文采用双包层掺镱光纤作为增益介质,用单壁碳纳米管作为饱和吸收体,获得最高输出功率为336 mW的锁模脉冲激光.用飞秒激光诱导水击穿法直接在单模光纤上制备出D形区,通过在D形光纤上滴涂单壁碳纳米管溶液,成功制备出碳纳米管饱和吸收体,并对其饱和吸收特性进行测试,发现其调制深度为27％.利用该饱和吸收体作为锁模器件,制备出具有环形腔结构的锁模光纤激光器.当抽运功率为4W时,获得了脉宽为93.8 fs,中心波长为1083.8 nm,3 dB谱宽为8.6 nm,重复频率为5.59 MHz,平均功率为336 mW的飞秒脉冲激光输出.