ZnO/Ag复合纳米粒子的制备与表征

以乙酸锌为前驱物,乙醇为溶剂,油酸钠为表面修饰剂,采用溶液化学法,在乙醇体系中制得纳米Zn O。然后缓慢加入一定量的硝酸银乙醇溶液,在乙醇的还原作用下将Ag+还原为Ag纳米粒子,制得Zn O/Ag复合纳米粒子。通过紫外-可见吸收光谱(UV-Vis)、荧光光谱(FL)、透射电子显微镜(TEM)和X射线衍射(XRD)等方法对所制备的氧化锌-银复合纳米粒子样品进行表征。结果表明,所合成的Zn O/Ag复合纳米粒子为球形,尺寸为20-30nm且粒径分布较窄。Ag纳米粒子附着于Zn O纳米粒子表面,并起到良好的表面修饰作用。对制备Zn O/Ag复合纳米粒子的机理进行了初步探究。     

Effect of nanoparticle network formation on electromagnetic properties and cell morphology of microcellular polymer nanocomposite foams

Adding high loadings of nanoparticles can remarkably alter the functionality of polymer nanocomposite foams. Therefore, this dramatic change was studied at the percolation threshold as a point to predict the properties of foamed nanocomposites using the viscoelastic characteristics of un-foamed ones. In this research, the effect of incorporating 10–40 wt% of ZnO nanoparticles on rheological properties of PS/ZnO samples was investigated. Then, these samples were foamed at processing temperatures of 80 and 120 °C to study morphology and electromagnetic properties. First, the rheological study showed that the storage modulus of nanocomposites increased significantly above 20 wt% of nanoparticles. A connected network of nanoparticles altered the microstructure of nanocomposite at this rheological percolation. The morphological results show a higher cell density for foamed samples above the rheological percolation. From electromagnetic properties, the effect of ZnO connected network is obvious on the absorption enhancement for 30 and 40 wt% and only for 40 wt% of ZnO at 80 and 120 °C, respectively. Therefore, the viscoelastic properties of samples are still dominant at the lower temperature, but the foam structure became more important at the higher temperatures. This shows that the role of the filler network faded at the higher temperature and electromagnetic properties were changed with the foam structure. The microstructure expansion results in the decrease of filler amount at a fixed volume of foams, so more filler fraction is required to form a connected network of nanoparticles.     

Structural,thermal, optical and conductivity studies of Co/ZnO nanoparticles doped CMC polymer for solid state battery applications

In this study, a simple chemical precipitation method was used to synthesize ZnO: Co²⁺ as nanoparticles. The solution casting technique was used for the preparation of polymer films of Carboxymethyl cellulose (CMC) doped with different contents (0.5, 1.5, 3, and 5 wt%) of ZnO/Co NPs. As shown by the X-ray diffraction, the average size of ZnO/Co crystallite of the NPs is 25.6 nm. Meanwhile, the addition of ZnO/Co reduced the semi-crystallinity of CMC. The Fourier transform infrared (FTIR) confirmed the interaction between the ZnO/Co NPs and the polymer CMC. The direct and indirect band gap (Eg) was reduced from (5.32–5.01 eV and 5.20 to 4.99 eV respectively) with the increase in ZnO/Co NPs content up to 3 wt% after this content the Eg is increased as shown by the UV–Vis spectra. In addition, the results of TGA displayed the decomposition of the nanocomposite to be little compared to that of the pure CMC indicating the success of fabrication of products. The improvement of the ionic conductivity was noticed upon the addition of ZnO/Co NPs into the polymer CMC system which can be explained in terms of an increase in amorphicity as shown by the impedance spectroscopic study. It was found that the optimum ionic conductivity (3.209 × 10⁻⁶ Scm⁻¹) at ambient temperature was higher for the sample containing 1.5 wt% ZnO/Co NPs with highest of amorphicity and the lowest total loss of weight. Therefore, the improvements in optical properties, thermal stability, and AC conductivity which were observed represent a strong support for the use of the nanocomposite films in the solid state battery applications.     

氧分压对磁控溅射制备ZnO薄膜的结构及光学特性的影响

采用射频反应磁控溅射法在玻璃衬底上成功制备出具有c轴高择优取向的ZnO薄膜,利用X射线衍射及紫外-可见吸收和透射光谱研究了氧分压变化对ZnO薄膜的微观结构及光吸收特性的影响。结果表明,当工作气压恒定时,用射频反应磁控溅射制备的ZnO薄膜的生长行为主要取决于成膜空间中氧的密度,合适的氧分压能够提高ZnO薄膜的结晶质量;薄膜在可见光区的平均透过率达到90%以上,且随着氧分压的增大,薄膜的光学带隙发生了一定程度的变化。采用量子限域模型对薄膜的光学带隙作了相应的理论计算,计算结果与对样品吸收谱所作的拟合结果符合较好,二者的变化趋势完全一致,表明ZnO纳米晶粒较小时,薄膜光学带隙的变化与量子限域效应有很大关系。     

常温直接沉淀法制备ZnO纳米棒

在常温下, 以PEG-400(聚乙二醇400)为表面活性剂, 采用直接沉淀法合成了ZnO纳米棒. 产物用XRD, TEM, SAED和 HRTEM等进行了表征. 结果表明, 所得ZnO为一维的纳米棒, 属于六方纤维矿的单晶结构. ZnO纳米棒的直径在20~40 nm之间, 长度在300~800 nm范围. (0001)面为ZnO纳米棒的生长方向. 讨论了ZnO相的生成和ZnO纳米棒的形成机理以及PEG-400在其形成过程中的作用.     

水溶性ZnO量子点制备及其光学性质

利用3-巯丙基三乙氧基硅烷对ZnO进行表面修饰后沉积SiO2, 制备出水溶性SiO2包覆ZnO的量子点. 与直接采用正硅酸乙酯沉积包覆SiO2的ZnO量子点相比, 362 nm处的激子荧光发射峰的强度提高了将近4倍. 由于表面引入了巯基官能团, 量子点的水溶性明显提高, 稳定性增强, 即使在较高的盐浓度下也不会团聚. 通过改变条件, 制备出了发光波长在420 nm的蓝色荧光量子点.     

紫外光激发下氧化锌纳米线的发光特性研究

室温条件下,用355 nm的激光激发氧化锌纳米线,测量了其发光光谱.观察到半宽度较小、峰值波长约382 nm的紫光峰和半宽度较宽、峰值波长约507 nm的绿光峰;两峰的发光强度随激发光功率密度的变化而变化,且均存在饱和效应,但各自的变化规律及饱和值的大小不同;紫光峰的中心波长随激发光功率密度的增加而发生了明显的红移.对两峰产生的机理、强度饱和值存在的原由、强度随激发光功率密度变化及紫光峰红移的起因进行了分析.     

用锌有机源和CO2/H2混合气源PECVD沉积ZnO薄膜

在等离子体作用下,以CO2/H2混合气为氧源,Zn(C2H5)2锌为锌源,在单晶硅上生长出高度择优取向的氧化锌薄膜。X射线衍射分析表明,薄膜为六方结构,c轴高度择优;原子力显微镜观察到晶粒是有规律地按六方排布,薄膜的表面粗糙度较小;从光致发光谱还发现在380 nm处有非常强的紫外峰。     

常压化学气相沉积技术生长ZnO:H薄膜的光学性质

采用常压金属有机物化学气相沉积技术(AP-MOCVD),以二乙基锌(DEZn)为Zn源,去离子水(H2O)为氧源,N2作载气,在外延ZnO薄膜的反应气氛中通入少量氢气,在c-Al2O3衬底上生长出了ZnO∶H薄膜。用X射线双晶衍射和光致发光谱对ZnO∶H薄膜的结晶性能和光学性质进行表征。结果表明,ZnO∶H薄膜(002)和(102)面的Ω扫描半峰全宽分别为46.1 mrad和81.4 mrad,表明该薄膜具有良好的结晶性能;室温下,ZnO∶H薄膜具有较强的紫外光发射(380 nm),在低温10 K光致发光谱中观测到位于3.3630 eV处与氢相关的中性施主束缚激子峰(I4)及其位于3.331 eV处的双电子卫星峰(TES)。采用退火的方法,通过观测I4峰的强度变化,研究了氢在ZnO∶H薄膜中的热稳定性。发现随着退火温度的升高,I4峰的强度逐渐减弱,表明在高温下退火,氢会从ZnO薄膜中逸出。     

高温高压下氧化锌纳米晶的晶粒演化动力学

用GS-1B型六面顶压机研究了ZnO纳米晶高温高压下的晶粒演化动力学, 用MDI/JADE5 X射线衍射仪(Cu靶)和XL30S-FEG场发射扫描电子显微镜对高压样品的相组成、晶粒尺寸及微观形貌进行了表征. 实验发现300 ℃(包括300 ℃)以下, ZnO纳米材料中晶粒生长速率随着压力的升高先增大后减小, 1～3 GPa烧结体晶粒尺寸随着压力的升高而增大, 4～6 GPa烧结体晶粒尺寸随着压力的升高而减小. 利用高压下晶粒生长速率方程求出1～3 GPa, 4～6 GPa的激活体积分别为－5.82, 9.66 cm³/mol. 400 ℃(包括400 ℃)以上, 1～6 GPa烧结体的晶粒尺寸随着压力的升高而不断增大.