微波合成铝掺杂钻酸锂材料及性能研究

以LiOH·H2O，Al2O3和Co3O4为原料，微波加热合成Li离子电池正极材料LiAlxCo（1-x）O2．通过XRD测试表征了不同Al加入量时合成产物的晶体结构，确定当x≤0．4时，产物为单一相层状结构．计算了不同x时LiAlxCo（1-x）O2的晶胞参数，随着x的增大，a值减小，c值增大．对合成LiAlxCo（1-x）O2样品进行DSC—TGA测试，结果表明，当x不同时，合成样品的热稳定性不同．SEM测试表明，合成晶体粒度较均匀，粒径在5μm左右．电化学测试表明，LiAl0.2Co0.8O2的电化学性能最好，首次循环放电容量为127mAh／g，多次循环容量损失率小于LiCoO2．     

Surface structure and electrochemical characteristics of natural graphite fluorinated by ClF3

Natural graphite samples with average particle sizes of 5, 10 and 15 μm (NG5 μm, NG10 μm and NG15 μm, respectively) were fluorinated by ClF₃ (3 × 10⁴ Pa) at 200 and 300 °C for 2 min. X-ray photoelectron spectra of surface-fluorinated samples showed that surface fluorine concentration increased with increase in the particle size of graphite and reaction temperature. Small amounts of chlorine were also detected in all the fluorinated samples. Raman spectra of original and surface-fluorinated samples indicated that the surface disordering was increased for NG10 μm and NG15 μm. Surface areas were decreased by the fluorination for NG5 μm and NG10 μm but unchanged for NG15 μm. The mesopores with diameter of 1.5-2 nm increased while those of 2-3 nm decreased for all the samples. First coulombic efficiencies for NG10 μm and NG15 μm were highly increased by surface fluorination in 1 mol/dm³ LiClO₄-EC/DEC/PC (EC: ethylene carbonate, DEC: diethyl carbonate, PC: propylene carbonate) solution.     

Synthesis and electrochemical properties of spinel LiMn2O4 prepared by the rheological phase method

Pure-phase and well-crystallized spinel LiMn₂O₄ powders were successfully synthesized by a simple rheological phase method. The thermal behavior and structure properties of the powders prepared by the rheological phase method compared with the solid-state reaction were investigated by thermogravimetry, powder X-ray diffraction , scanning electron microscopy and transmission electron microscopy. According to the results of the electrochemical tests, it is obvious that the sample resulting from the rheological phase method shows higher discharge capacity and better cycling stability than one formed in the solid-state reaction. The cyclic voltammogram and columbic efficiency curves also confirm that the product by the rheological phase method has a good cycling performance due to its fine cubic spinel structure and morphology.     

氯化钠对锂离子电池石墨负极的修饰改性

Numerous carbonaceous materials have been studied as anodes of lithium ion batteries during the past several years[1￣4].Graphite was favored for battery applications because it exhibits a high specific capac- ity, low working potential close to that of l…     

A DFT study of lithium battery materials: application to the β-VOXO4 systems (X=P, As, S)

VOXO₄ systems have been considered as potential lithium battery electrodes. They mainly present two distinct structural types: the tetragonal “α” type with a two-dimensional framework, and the three-dimensional orthorhombic “β”. DFT calculations were performed on this latter system for several β-Li_xVOXO₄ compounds (x=0, 1; X=P, As, S). They allowed to propose structural models for VOAsO₄ and LiVOSO₄, not fully crystallographically well described yet. Based on an experimental model of two-phase processes, these calculations led also to a good simulation of electrochemical potential values. A density of states analysis put in evidence the “inductive effect” and the role played by (XO₄)ⁿ⁻ groups inside the host frameworks on these potentials.     

PVC DISULFIDE AS CATHODE MATERIALS FOR SECONDARY LITHIUM BATTERIES

PVC disulfide (2SPVC) was synthesized by solution crosslink and its molecular structure was confirmed by infrared spectrum. 2SPVC's specific area is 36.1 m2·g-1 tested by stand BET method, and granularity experiment gives out the particle size of d0.5= 11.3μm. With SEM (Scanning Electron Microscope) experiment the surface morphology and particle shape of 2SPVC were observed. Cyclic voltammetry (scan rate: 0.5 mV·s-1) shows that 2SPVC experience an obvious S-S redox reaction in charge-discharge process. When 2SPVC was used as cathode material for secondary lithium battery in a 1 mol·L-1 solution of lithium bis(trifluoromethylsulfonyl) imide (Li(CF3SO2)2N) in a 5:45:50 volume ratio mixture of o-xylene (oxy), diglyme (DG) and dimethoxymethane (DME) at 30℃, the first discharge capacity of 2SPVC is about 400.3 mAh·g-1 which is very close to its theoretical value (410.5 mAh·g-1) at a constant discharge current of 15 mA·g-1. It can retain at about 346.1 mAh·g-1 of discharge capacity after 30 charge-discharge cycles. So 2SPVC is a very promising cathode candidate for rechargeable lithium batteries.     

聚1-氨基蒽醌在二次锂电池正极材料中的应用

采用化学方法合成聚1-氨基蒽醌并用于二次锂电池正极材料,通过红外光谱、扫描电镜、粒度测试、循环伏安以及充放电测试等方法对材料的官能团结构、微观形貌、颗粒大小以及电化学性能等进行了研究与分析.实验表明,与金属锂组成二次锂电池后,聚1-氨基蒽醌达到了218.3 mAh•g－1的首次放电容量,经过25次循环后仍可保持较高的充放电效率.由于材料具有较高的能量密度且不含对环境有污染的元素S,因此是二次锂电池非常有希望的正极材料.     

高温固相法合成LiNi1/3Mn1/3Co1/3O2及其性能研究

采用高温固相法合成出层状锂离子电池正极材料LiNi_1/3Mn_1/3Co_1/3O₂。通过XRD、ICP、SEM和电化学测试手段对产物的结构、组成、形貌及电化学性能进行了研究。XRD结果表明此方法合成的LiNi_1/3Mn_1/3Co_1/3O₂具有标准的α-NaFeO₂型层状结构，SEM照片显示颗粒粒径大约在500 nm左右，粒径分布较窄。以20 mA·g^-1电流密度放电，充放电电压在2.8～4.4 V之间，其首次放电比容量为170 mAh·g^-1，40次循环容量保持率为85.3%。进一步加入石墨导电剂后，同样条件下首次放电比容量变为179 mAh·g^-1，50次循环容量保持率为89.6%。容量衰减主要发生在前10次循环。XRD和SEM测试表明循环初期容量衰减的原因是由材料本体结构变化和界面反应共同作用的结果。     

利用湿法反应制备的LiV3O8的锂离子扩散特性

利用V2O5•nH2O湿凝胶和Li2CO3作原料,通过溶液反应和低温焙烧的方法合成了用于锂离子电池正极的LiV3O8.对其前驱体和产品分别进行DTA-TG、XRD表征.LiV3O8用作锂离子电池正极的电化学性能利用恒电流充放电测试进行研究.实验表明活性材料LiV3O8具有较高的充放容量和良好的循环性能.LiV3O8电极的锂离子化学扩散系数由恒电位间歇滴定技术(PITT)来确定，其值依据Li1＋xV3O8中x值的不同在10－8～10－10 cm2•s－1的变化范围内.获得的锂离子的扩散活化能为：Ea=25～42 kJ•mol－1(x=0.18～2.5).认为锂离子扩散的最大活化能是由锂离子在Li4V3O8相中的扩散决定的.     

Impact Responses of Prismatic Lithium-Ion Battery Based on the Membrane Factor Method北大核心CSCD

Aimed at the internal short circuit problem due to large deformation of the prismatic lithium-ion battery cell under impact loadings, a simplified battery model was first established. Then the motion equations of velocity and displacement based on the membrane factor method were proposed. With the effects of the face-sheet thickness and the densification region on the normalized final deflection, impact response characteristics of prismatic battery cells were investigated in detail. The results show that, the improved motion equations involving the membrane factor can reflect the dynamic response mechanisms of the prismatic battery cell under impact loadings, and the large deflection under high-speed impact can be predicted. With the increase of the face-sheet thickness, the deflection of the battery cell’s lower part decreases obviously. However, the densification region expands with the face-sheet thickness. The deflection and the densification region of the cell’s lower part both increase with the inner core density of the battery. This proposed impact model provides a theoretical guidance for the multi-functional integrated dynamic design of prismatic battery cells. © 2022 Editorial Office of Applied Mathematics and Mechanics. All rights reserved.