层状氢氧化苯甲酸锌的水热合成与表征

在110～180 ℃范围内, 以Zn(OH)2与苯甲酸为原料水热法成功合成了层状氢氧化苯甲酸锌化合物. 通过XRD、TG-DTA、SEM、TEM和元素分析研究了合成产物的结构、形貌、性质和化学组成, 探讨了合成条件对水热反应产物的影响. 当C6H5COOH/Zn的摩尔比为0.9～1.0, 水热温度130～150 ℃及水热反应12 h, 合成的层状化合物具有纤维状粒子特征, 层间距为1.44 nm, 化学组成为Zn(OH)1.12•(C6H5COO)0.88.     

反相微乳液助水热法可控合成FeNi3合金纳米结构

利用水热法处理表面活性剂/正辛烷/正己醇/水四元微乳体系成功合成FeNi3合金纳米结构. 通过改变表面活性剂的用量和类型来调控产物粒径与形貌. 当表面活性剂为聚乙二醇4000(PEG4000)时, 产物为球状, 粒径约为75 nm. 当表面活性剂为十六烷基三甲基溴化铵(CTAB)时, 产物为海胆状.单个海胆状颗粒是由许多纳米棒构成, 其直径约为42 nm, 长度为0.4-1.2 μm. 利用X射线粉末衍射(XRD), 穆斯堡尔谱, 扫描电子显微镜(SEM), 透射电子显微镜(TEM), 选区电子衍射(SAED), 多功能磁天平(MMVFTB)等测试手段对产物的组成、形貌和磁性能进行了表征. 球状和海胆状的FeNi3样品在室温下呈现典型的铁磁性特征, 其饱和磁化强度(Ms)值分别为114.4和97.4 emu·g-1, 矫顽力(Hc)值分别为94.0和329.0 Oe.     

用水热法在铁铬铝合金片上原位合成MCM-22沸石膜

 采用水热法在铁铬铝合金片载体上原位合成了MCM-22沸石膜,并采用X射线衍射和扫描电子显微镜对沸石膜进行了表征,探讨了成膜的影响因素. 结果表明,载体预处理条件对合成沸石膜的品质有较大的影响. 载体仅经碱处理后合成的沸石膜稀疏而不连续; 载体先经碱处理再经酸处理后可得到连续致密的沸石膜,且晶片取向均一; 载体预先涂覆Al2O3胶过渡层后制得的MCM-22沸石膜经超声波清洗后不会脱落,表明沸石膜与载体间的结合力增强. 此外,增大晶化母液量有利于沸石膜的生长.     

铁铬合金团簇点阵中与成分相关的磁性耦合

本文采用气相团簇束流沉积法制备了不同铁铬比的铁铬合金密集团簇点阵,研究了团簇点阵中复杂的多相结构和各种耦合效应.当合金中铬含量较大时,在团簇中能够观测到一种晶格失配的类四方结构,这种结构的出现导致了不同铁铬比的合金团簇中交换偏置效应的不同.随着铬的含量增加,合金团簇的交换偏置场减小,而团簇间的偶极相互作用增强.在合金团簇的铁磁-超顺磁转变温度以上,能明显观察到在类四方结构团簇中有更大的残存矫顽力与剩磁.在场冷条件下,对矫顽力和偏置场随温度变化的研究表明含有更多类四方结构的合金团簇有更好的热稳定性和更大的各向异性.     

Mesoporous Rh Emerging from Nanophase‐separated Rh‐Y Alloy

Mesoporous precious metals with abundant active sites and high surface area have been widely recognized as high‐performance catalytic materials. However, the templated synthesis is complex and costly. Herein, we report a mesoporous rhodium (m‐Rh) that can be readily synthesized from entangled nanofibres of Rh and Y₂O₃ without templates. The entangled nanofibres, prepared from uniform Rh‐Y alloys under redox atmosphere, were the key precursor in the synthesis processes. Moreover, the m‐Rh efficiently catalyzed carbon dioxide reforming of methane (DRM) at a low reaction temperature of 683 K. Further, electrochemical methods of CO electro‐oxidation were innovatively used to demonstrate the stability of CO and oxygen species for the DRM reaction.     

Thermal stability of microstructures and mechanical properties in a Fe-based Fe-Cr-Mn-Cu-Mo multi-component alloy

A Fe-based multi-component alloy, 60Fe-12Cr-10Mn-15Cu-3Mo, was designed and fabricated for nuclear applications in the present study. The crystal structure of the alloy is a ～85% body – and 15% face–centered cubic. A detailed microstructure analysis indicated that Cu segregated in the alloy to form Cu-rich precipitates, and the Cu precipitates grew during high temperature annealing at up to 773?K. The high temperature tensile test of the alloys showed that both the yield stress and tensile strength of the 60Fe-12Cr-10Mn-15Cu-3Mo were greater than those of typical austenitic and ferritic stainless steels at 773?K. The Vickers microhardness of the designed alloy did not change after high temperature annealing for 1?h at up to 1073?K. The results indicated that the designed alloy has the potential to be used for high temperature applications.     

Analysis of precipitates in ultrafine-grained metallic materials

In the present work, new possibilities of the X-ray diffraction for investigations of the phase composition, size, shape and volume fraction of particles in ultrafine-grained ferritic/martensitic steel and the Cu-Cr-Zr alloy have been demonstrated. For the first time, the method of X-ray diffraction in the transmission mode was used to identify particles with a volume fraction of less than one percent in the ultrafine-grained materials studied. The small-angle X-ray scattering method was used to estimate the size and shape of dispersed particles. Specific features of the ultrafine-grained structure determined by the X-ray diffraction and transmission electron microscopy studies were used for estimation of dispersion hardening in the samples obtained by equal-channel angular pressing in comparison with the samples subjected to standard treatment.     

Mass and thermal transport in liquid Cu-Ag alloys

In this paper, the diffusion, thermodynamic and thermotransport properties in Cu–Ag liquid alloys are extensively investigated with molecular dynamics over a wide composition and temperature range. The simulations are performed with the most reliable EAM potential. The Green-Kubo formalism is employed for calculating transport properties. It is found that the reduced heat of transport in Cu–Ag is very small (about 0.10?eV in absolute value) and almost temperature independent. Further it is found that the interdiffusion coefficient together with both self-diffusion coefficients are almost composition independent. In Cu–Ag, the thermodynamic factor is found to be less than unity whereas the Manning factor is greater than unity (with significant composition and temperature dependence) and their product is very close to 1.     

硫原子在镍基合金825(001)面吸附的第一性原理研究

元素硫在镍基合金表面吸附产生严重的电化学腐蚀,为从原子尺度研究硫腐蚀机理,采用第一性原理方法,构建并优化了镍基合金825的晶胞结构模型,计算分析了S原子在镍基合金825耐蚀性较差面(001)晶面的吸附及电子转移情况.结果表明:Ni原子占据顶角, Cr原子和Fe原子对称占据面心是镍基合金825稳定的晶胞结构;原子S在镍基合金825(001)面上最稳定的吸附位为四重穴位,吸附能为-6.51 eV; S吸附前后的态密度(DOS)和二维电荷差分密度图(DCD)对比发现,镍基合金825中Fe与S之间电荷偏移明显,形成离子键,易生成腐蚀产物Fe_xS_y. S的吸附对镍基合金825中Cr原子的电子分布影响不大,且合金中Cr和Ni抑制了合金中Fe与S之间的相互作用,从而提高了合金耐蚀性.