Design and Application of a Set of Vitreous Standards for EDS-SEM Microanalysis of Melting Shop Slags

Non-metallic inclusions in steel are formed due to interactions between liquid steel and its environment in the melting shop (refractories and slags). Particles not trapped in the slag remain in the cast steel, impairing steel properties in service. Inclusion composition varies and certified standards covering the whole compositional range are unavailable.The present study describes the preparation of a set of homogeneous, glassy and crystalline standards with a wide compositional range for use in analysing non-metallic steel inclusions. For this, materials were designed based on knowledge of the compositional range of interest in the Al₂O₃–SiO₂–CaO–MgO–CaF₂ system, which is the matrix of the most frequent steel inclusions. The composition and microstructural homogeneity of the reference materials was verified.     

Fast solid-phase extraction-gas chromatography-mass spectrometry procedure for oil fingerprinting. Application to the Prestige oil spill

A rapid and simple fractionation procedure using solid-phase extraction (SPE) cartridges was developed for an accurate determination of aliphatic and polycyclic aromatic hydrocarbons in petroleum residues and further application in chemical fingerprinting of oil spills by gas chromatography-mass spectrometry (GC-MS). Among the adsorbents evaluated, SiO2/C3-CN exhibited the best selectivity, providing, by elution with n-hexane (4 ml) and n-hexane-CH2Cl2 (1:1) (5 ml), two well-resolved aliphatic and aromatic hydrocarbon fractions, with recoveries of 97 +/- 7.2 and 99.7 +/- 13.9%, respectively. The SPE fractionation procedure was compared with the conventional silica-alumina adsorption chromatography showing similar results but practical advantages in terms of reproducibility, analysis time, solvent reduction and cost. Moreover, is particularly suitable for routine analysis with a high sample throughput. The developed methodology was tested in the characterization of fuel-oil samples collected along the Spanish north-west coast, after the Prestige oil spill accident.     

Determination of As, Sb, Se, Te and Bi in milk by slurry sampling hydride generation atomic fluorescence spectrometry

A simple and fast analytical procedure has been developed for the determination of As, Sb, Se, Te and Bi in milk samples by hydride generation atomic fluorescence spectrometry (HG-AFS). Samples were treated with aqua regia for 10 min in an ultrasound water bath and pre-reduced with KBr for total Se and Te determination or with KI and ascorbic acid for total As and Sb, the determination of Bi being possible in all with or without pre-reduction. Slurries of samples, in the presence of antifoam A, were treated with NaBH₄ in HCl medium to obtain the corresponding hydrides, and AFS measurements were processed in front of external calibrations prepared and measured in the same way as samples. Results obtained by the developed procedure compare well with those found after microwave-assisted complete digestion of samples. The proposed method is simple and fast, and only 1 ml of milk is needed. The values obtained for detection limit are 2.5, 1.6, 3, 6 and 7 ng l⁻¹ for As, Sb, Se, Te and Bi respectively in the diluted samples, with average relative standard deviation values of 3.8, 3.1, 1.9, 6.4 and 1.2% for three independent analysis of a series of commercially available samples of different origin. Data found in Spanish market samples varied from 3.2±0.3 to 11.3±0.2 ng g⁻¹ As, from 3.1±0.2 to 11.6±0.4 ng g⁻¹ Sb, from 10.7±0.5 to 25.5±0.4 ng g⁻¹ Se, from 0.9±0.2 to 9.4±0.6 ng g⁻¹ Te and from 11.5±0.1 to 27.7±0.4 ng g⁻¹ Bi.     

Liquid chromatographic determination of aliphatic amines in water using solid support assisted derivatization with 9-fluorenylmethyl chloroformate

Summary A simple and sensitive method has been developed for the liquid chromatographic determination of short-chain aliphatic amines in water. Analytes are retained in solid-phase extraction (SPE) cartridges, and then derivatized by drawing an aliquot of the fluorogeneic reagent 9-fluorenylmethyl chloroformate (FMOC) through the cartridges. After a certain reaction time the derivatives formed are desorbed with acetonitrile. The collected extracts are then chromatographed on a LiChrospher 100 RP₁₈ 125 mm×4 mm i.d., 5 μm, column using an acetonitrile-water gradient. The influence of experimental conditions (SPE material, volume of sample, concentration of FMOC, time of reaction and pH) has been investigated. Optimal results have been obtained with C₁₈ SPE cartridges using a sample volume of 5.0 mL. For derivatization, 0.25 mL aliquots of 25 mM FMOC have been used, the reaction time being only 2 min. The method has been applied to the quantification of several aliphatic amines: methylamine, ethylamine, dimethylamine,n-butylamine,n-pentylamine andn-hexylamine. Under the proposed conditions the percentages of analytes retained plus derivatized were of about 54–107% compared to those obtained with direct solution derivatization. The method provided good reproducibility, linearity and accuracy within the 0.050–1.0 mg L⁻¹ concentration range. The limits of detection were in the 0.25–5.0 μg L⁻¹ range. The utility of the described approach has been tested by analysing tap water, river water and industrial waste water.     

Comparative Characteristics of Some Physicochemical Properties of Azoles

We have carried out a correlation analysis of some physicochemical characteristics of pyrrole, pyrazole, imidazole, triazole, and tetrazole, calculated by the semiempirical quantum-chemical AM1 method. We have found the linear dependences of the ionization potential, the dipole moment, and the acidity on the -electron excess, and also the dependence of the ionization potential on the enthalpy of formation of the studied azoles.     

Coupling continuous ultrasound-assisted extraction, preconcentration and flame atomic absorption spectrometric detection for the determination of cadmium and lead in mussel samples

Continuous ultrasound-assisted extraction has been coupled with preconcentration and flame atomic absorption spectrometry for the determination of cadmium and lead in mussel samples. Experimental designs were used for the optimisation of the leaching and preconcentration steps. The use of diluted nitric acid as extractant in the continuous mode at a flow rate of 3.5 ml min⁻¹ and room temperature was sufficient for quantitative extraction of these trace metals. A minicolumn containing a chelating resin (Chelite P, with aminomethylphosphoric acid groups) was proved as an excellent material for the quantitative preconcentration of cadmium and lead prior to their flame atomic absorption detection. A flow injection manifold was used as interface for coupling the three analytical steps, which allowed the automation of the whole analytical process. A good precision of the whole procedure (2.0 and 2.3%), high enrichment factors (20.5 and 11.8) and a detection limit of 0.011 and 0.25 μg g⁻¹ for cadmium and lead, respectively, were obtained for 80 mg of sample. The sample throughputs were ca. 16 and 14 samples h⁻¹ for cadmium and lead, respectively. The accuracy of the analytical procedures was verified by using a standard reference material (BCR 278-R, mussel tissue) and the results were in good agreement with the certified values. The method was successfully applied to the determination of trace amounts of cadmium and lead in mussel samples from the coast of Galicia (NW, Spain).     

Metal speciation measurement by diffusive gradients in thin films technique with different binding phases

Since its invention in the mid-1990s, the diffusive gradients in thin films (DGT) technique has rapidly become one of the most promising in situ sampling techniques for trace metal measurement in natural waters. We investigated here the possibility of using DGT devices with different binding phases to determine different DGT labile fractions of Cd and Cu in laboratory solutions and in natural waters. Several binding phases were studied, including conventional Chelex 100 resin imbedded polyacrylamide hydrogel (Chelex) and several recently developed binding phases, poly(acrylamide-co-acrylic acid) (PAM-PAA) gel, poly(acrylamidoglycolic acid-co-acrylamide) (PAAG-PAM) gel, Whatman P81 cellulose phosphate ion-exchange membrane (P81), and poly(4-styrenesulfonate) (PSS) aqueous solution. Laboratory testing in metal solutions spiked with EDTA or humic acid suggested that all the DGT devices measured only free metal ions and inorganic metal complexes. Upon field testing at both freshwater and seawater sites it was found that the DGT labile metal concentrations measured by different binding phases can be significantly different, suggesting that the DGT labile metal fractions were dependent on binding strength of the binding phase. By designing binding phases that can compete with different natural water complexing ligands to varying extents, it is possible to use these different DGT devices to measure metal speciation in natural waters.     

A molecular mechanics and semiempirical conformational analysis of the herbicide diuron inhibitor of photosystem II

The potential energy surface (PES) for the herbicide diuron (DCMU), a photosystem II inhibitor, has been extensively investigated using the quantum-mechanical semiempirical molecular orbital methods AM1 and PM3 and molecular mechanics method. A detailed conformational search has been carried out which revealed the occurrence of four genuine minimum energy structures. The relative stability of the conformers and rotational barriers to conformational interconversion were evaluated using distinct theoretical approaches. The results showed that thetrans form of the diuron molecule is more stable than thecis form in all methods, and so it may possibly be the biologically active isomer.