多通道反应O(3P)＋CH2F的理论研究

用密度泛函理论研究了氧原子与氟代甲基自由基的反应.反应中出现的所有物种的平衡构型用B3LYP方法在6-311＋＋G（2d, 2p）基组水平上进行了优化，同时对各物种进行了频率分析；在同一理论水平上计算了各反应通道的势能面变化，分析了反应物、中间体、过渡态、产物的振动模式随反应途径的变化关系，阐明了该多通道反应的反应机理.     

Influence of Al2O3 Nanoparticles on the Thermal Stability of Ultra-Fine Grained Copper Prepared by High Pressure Torsion

Summary.  Ultra-fine grained (UFG) Cu (grain size 80 nm) containing 0.5 wt.% Al₂O₃ nanoparticles (size 20 nm) was prepared by high pressure torsion (HPT). Positron lifetime spectroscopy was employed to characterize the microstructure of this material, especially with respect to types and concentration of lattice defects. The evolution of microstructure with increasing temperature was studied by positron lifetime spectroscopy and X-ray diffraction measurements. The thermal stability of the Cu + 0.5 wt.% Al₂O₃ nanocomposite was compared with that of pure UFG Cu prepared by the same technique. The processes taking place during thermal recovery of the initial nanoscale structure in both studied materials are described. Received October 5, 2001. Accepted (revised) December 20, 2001     

Density functional theory study of vibrational spectra, and assignment of fundamental vibrational modes of succinimide and N-bromosuccinimide

This work deals with the vibrational spectroscopy of succinimide and N-bromosuccinimide. The mid and far FTIR and FT-Raman spectra were measured in the condensed state. The fundamental vibrational frequencies and intensity of vibrational bands were evaluated using density functional theory (DFT) using standard B3LYP/6-31G(*) and B3LYP/6-311+G(**) methods and basis set combinations. The vibrational spectra were interpreted, with the aid of normal coordinate analysis based on a scaled quantum mechanical force field. The infrared and Raman spectra were also predicted from the calculated intensities. Comparison of simulated spectra with the experimental spectra provides important information about the ability of the computational method to describe the vibrational modes. Unambiguous vibrational assignment of all the fundamentals were made using the total energy distribution (TED).     

A new electrolytic dissolution of aluminum alloys and determination of some constituents by inductively coupled plasma optical emission spectrometry

The new electrolytic dissolution in batch of aluminum alloys samples as grains or turns and the determination of Fe, Cu, Mn, Mg, Cr, Ni, Zn, Pb and Ti by ICP OES was investigated. In on-line electrodissolution procedures described in the literature, samples were restricted to be in the form of solid blocks or plates with one polished flat face. Here, the sample was loaded in the barrel of a modified disposable syringe (the anodic semi-cell) and pressed with a modified plunger fitted with a platinum disk to establish electrical contact with the analyte. This arrangement was introduced in a beaker containing the electrolyte (1 mol L⁻¹ HNO₃) and a platinum wire as the cathode. The resulting solution from electrodissolution (0.6 A) was used for the ICP OES determinations. The influence of the aluminum concentration increase on the determination of the elements was evaluated. Electrodissolution of certified reference materials and commercial samples revealed relative errors lower than 10% for the elements Fe, Cu, Mg, Ni, Cr, Zn and Ti (when their content is above 0.1%). Higher inaccuracies (>10%) were observed for Mn and for Fe in B.C.S. 268/1 reference material certified. The proposed method presented a relative standard deviations (R.S.D.) lower or circa 10% to all of the elements (except Pb). In comparison with traditional acid dissolution, the proposed electrodissolution method is relatively fast (about 30 min), it is clean (there is no projection of solution) and simple (heating and fumes exhaust system were not necessaries).     

Darstellung, 11B-NMR-, Schwingungsspektren und Kristallstruktur von [(C5H5N)2CH2][1-(O2N)B10H9]

Preparation, ¹¹B NMR, Vibrational Spectra, and Crystal Structure of [(C₅H₅N)₂CH₂][1-(O₂N)B₁₀H₉] By reaction of [B₁₀H₁₀]^2? in aqueous acetonitrile with a saturated solution of NO₂ in dichloromethane [1-(O₂N) · B₁₀H₉]^2? and [B₁₀H₉(NO)B₁₀H₉]^3? are formed which can be separated by ion exchange chromatography on diethylaminoethyl(DEAE) cellulose from the starting compound. The X-ray structure determination of [(C₅H₅N)₂CH₂][1-(O₂N)B₁₀H₉] (triclinic, space group P1 , a = 7.1530(9), b = 8.3753(8), c = 15.198(2) Å, α = 96.00(1), β = 95.48(1), γ = 95.60(1)°, Z = 2) reveals the coordination of the NO₂ group via N with a B1? N distance of 1.535(5) Å and an O2? N? O1 angle of 119.3(3)°. The ¹¹B NMR spectrum exhibits the characteristic feature (1 : 1 : 4 : 4) of an apical monosubstituted B₁₀ cluster with a strong downfield shift of the ipso-B atom at +13.4 ppm. The IR and Raman spectra show strong NO stretching vibrations at 1381 und 1420 cm^?1.     

Vibrational frequencies and structural determination of phosphirane

The normal mode frequencies and corresponding vibrational assignments of phosphirane in are examined theoretically using the GAUSSIAN 98 set of quantum chemistry codes. All normal modes were successfully assigned to one of nine types of motion (C–C stretch, P–C stretch C–H stretch, P–H stretch, CH₂ scissors, CH₂ wag, CH₂ rock, CH₂ twist, and P–H wag) predicted by a group theoretical analysis. Comparing the vibrational frequencies with IR and Raman spectra available in the literature, a set of scaling factors are derived. Predicted infrared and Raman intensities are reported.     

Vibrational spectrum of BiH3: Six-dimensional variational calculations on high-level ab initio potential energy surfaces

We report a theoretical study of the ground electronic state of BiH₃. The potential energy surface (PES) is obtained from coupled cluster CCSD(T) calculations with a large basis set (289 contracted Gaussian functions). The previously available quartic force field (P4) is extended by adding the dominant quintic and sextic stretching terms to yield improved potential functions in symmetry coordinates (P6) and Morse-type coordinates (M4). Second-order rovibrational perturbation calculations on the P4-PES and full variational calculations on the P6-PES and M4-PES yield almost identical vibrational term values which is rationalized by considering the local mode behavior of BiH₃ and the Morse-type character of the M4-PES. The remaining deviations between the computed and observed vibrational term values must thus be caused by imperfections in the CCSD(T) surface. A refinement of this ab initio surface by a restrained fit to experimental data allows an essentially perfect reproduction of the observed vibrational term values. Variational calculations on this refined surface provide predictions for several overtone and combination bands that have not yet been observed. Dedicated to Hermann Stoll on the occasion of his 60th birthday     

Comparison of zinc and cadmium plasma parameters produced by laser-ablation

We report the measurement of the zinc and cadmium plasma parameters produced by the fundamental, second, and third harmonics of the neodymium-doped yttrium aluminium garnet laser. The excitation temperature has been determined from the Boltzmann plot method, whereas the electron number density is estimated from the Stark broadened profile of several spectral lines. The temporal evolution of the plasma has also been investigated. Besides, we present experimental relative transition probabilities of the Zn (4s5s ³S₁ → 4s4p ³P_0,1,2) and Cd (5s6s ³S₁ → 5s5p ³P_0,1,2) triplets and compare our data with that listed in the National Institute of Standards and Technology database. The experiments have been performed in air but also in He, Ne and Ar atmosphere to study the effects of ambient gas environment on the emission intensity of the atomic and ionic lines and on the plasma parameters.     

Analysis of the effects of catalytic bleaching on cotton

Hydrogen peroxide can be catalyzed to bleach cotton fibers at temperatures as low as 30°C by incorporating dinuclear tri-μ-oxo bridged manganese(IV) complex of the ligand 1,4,7-trimethyl-1,4,7-triazacyclononane (MnTACN) as the catalyst in the bleaching solution. The catalytic system was found to be more selective under the conditions applied than the non-catalytic H₂O₂ system, showing better bleaching performance while causing slightly lower decrease in degree of polymerization (DP) of cellulose. In order to gain fundamental knowledge of the bleach effect on cotton fibers and cellulose as its main component, especially after catalytic bleaching, X-ray Photoelectron Spectroscopy (XPS) was used to study surface chemical effects. The Washburn method was applied to investigate wetting properties, and liquid porosity was used to obtain pore volume distribution (PVD) plots. Parallel analyzes performed on model cotton fabric, i.e. “clean” cotton fabric stained with morin - a pigment regularly found in native cotton fiber, helped to differentiate between pigment oxidation and other bleaching effects produced on the (regular) industrially scoured cotton fabric. Bleaching was not limited to the chemical action but also affected cotton fiber capillary parameters most likely due to the removal of non-cellulosic materials as well as chain-shortened cellulose.