Micro fabrication of microlens arrays by micro dispensing

In this study, master of the microlens arrays is fabricated using micro dispensing technology, and then electroforming technology is employed to replicate the Ni mold insert of the microlens arrays. Finally, micro hot embossing is performed to replicate the molded microlens arrays from the Ni mold insert. The resin material is used as the dispensing material, which is dropped on a glass substrate. The resin is exposed to a 380 W halogen light. It becomes convex under surface tension on the glass substrate. A master for the microlens arrays is then obtained. A 150‐nm‐thick copper layer is sputtered on the master as an electrically conducting layer. The electroforming method replicates the Ni mold insert from the master of the microlens arrays. Finally, micro hot embossing is adopted to replicate the molded microlens arrays. The micro hot embossing experiment employs optical films of polymethylmethacrylate (PMMA) and polycarbonate (PC). The processing parameters of micro hot embossing are processing temperature, embossing pressure, embossing time, and de‐molding temperature. Taguchi's method is applied to optimize the processing parameters of micro hot embossing for molded microlens arrays. An optical microscope and a surface profiler are utilized to measure the surface profile of the master, the Ni mold insert and the molded microlens arrays. AFM is employed to measure the surface roughness of the master, the Ni mold insert and the molded microlens arrays. The sag height and focal length are determined to elucidate the optical characteristics of the molded microlens arrays. Copyright © 2009 John & Sons, Ltd.     

A Nonenzymatic Glucose Sensor Based on a Copper Nanoparticle–Zinc Oxide Nanorod Array

A non-enzymatic sensor for glucose based on copper nanoparticles and zinc oxide nanorod array modified fluorine-doped tin oxide conductive glass electrode was constructed by two-step electrodeposition. The electrode was characterized by scanning electron microscopy and X-ray diffraction. The electrochemical behavior of the modified electrodes was investigated by cyclic voltammetry and electrochemical impedance spectroscopy. Under the optimal conditions, the modified electrode offered a rapid response to glucose in the range from 5 × 10^?6 M to 1.1 × 10^?3 M (R = 0.9975) with a detection limit of 3 × 10^?7 M (S/N = 3) and a sensitivity of 609.8 µA · mM^?1. The preparation and operation of the biosensor was simple, had lower cost, and offered excellent performance due to its high sensitivity, good stability, reproducibility, and selectivity against other substances. The satisfactory results illustrated that it was promising for the determination of glucose in alkaline solutions.     

An Amperometric Glucose Sensor Based on Isoporous Crystalline Protein Membranes as Immobilization Matrix

Abstract

S-layer ultrafiltration membranes (SUMs) with an active filtration layer composed of coherent two-dimensional, isoporous protein crystals (S-layers) have been used as matrix for immobilizing monolayers of enzymes. Since S-layers are formed by periodic repetition of identical protein subunits, functional groups are present on the crystalline array in an identical position and orientation. As a consequence monolayers of enzymes can bind in a geometrically well defined way. For the covalent immobilization of enzymes carboxyl groups from the S-layer protein were activated with carbodiimide and allowed to react with amino groups of the enzyme. SUMs were employed as a new type of immobilization matrix for the developement of an amperometric glucose sensor using glucose oxidase (GOD) as the biologically active component. Glucose oxidase covalently bound to the surface of the S-layer protein retained approximately 40% of its activity. The enzyme loaded SUMs were covered with a layer of gold or platinum to function as working electrodes. These sensors yielded high signals (150nA/mm²/mmol glucose), fast response times (10–30s) and a linearity range up to 12 mM glucose. The stability under working conditions was more than 48 hours. There was no loss in activity after a storage period of 6 month.     

ZnO纳米线/棒阵列的水热法制备及应用研究进展

氧化锌(ZnO)纳米线/棒阵列的质量决定了所构建光电器件的性能. 为了制备出比表面积更大、垂直性更好以及无根部融合的高质量ZnO纳米线/棒阵列, 本文概述了近几年两步水热法可控制备ZnO纳米线/棒阵列的研究进展, 分别探讨了种子层、生长液和生长方法对纳米线/棒阵列形貌的影响, 详细分析了氨水、六次甲基四胺和聚乙烯亚胺对于促进纳米线/棒阵列生长的作用机理, 提出了通过微流控技术可控制备ZnO纳米线阵列提高纳米线生长效率的方法. 最后介绍了ZnO纳米线/棒阵列的形貌对于提高染料敏化太阳能电池、纳米发电机、气体传感器和场发射器件性能的重要作用, 并对未来两步水热法制备ZnO纳米线/棒阵列的发展趋势进行了展望.     

Ti基ZnO纳米棒阵列的制备及其光催化性能研究

采用两电极体系中恒电流电沉积在Ti基底上制得较均一的ZnO纳米棒阵列,利用SEM和XRD观察表征样品,研究Zn(NO₃)₂浓度及电流密度对ZnO纳米棒阵列微观形貌的影响. 以甲基橙为目标降解物,考察该电极光催化性能. 结果表明,Zn(NO₃)₂浓度和电流密度对纳米棒阵列的形貌有显著影响;与ITO玻璃等其他基底相比,在Ti基底上也可沉积较好均一取向的ZnO纳米棒阵列;紫外灯照射下,ZnO/Ti电极对甲基橙（10 mg·L^-1）模拟印染废水降解2.5 h,降解率达到83.3%,光催化活性较佳;无光照时ZnO纳米棒的降解率仅7%.     

Tunable Surface‐Enhanced Raman Scattering from High‐Density Gold Semishell Arrays with Controllable Dimensions

A convenient reproducible technique is reported for the fabrication of large‐area gold semishell arrays by mechanically pressing porous anodic alumina (PAA) stamps into gold/polymer bilayer structures that serve as robust and cost‐efficient surface‐enhanced Raman‐scattering (SERS) substrates. The surface structure can be tuned further to optimize the enhancement factor according to optional PAA fabrication parameters and imprinting pressures. Finite‐difference time‐domain calculations indicate that the structure may possess excellent SERS characteristics due to the high density and abundance of hot spots.     

具有三维阵列结构的树枝晶CdS的制备及生长机理研究

采用电沉积和溶剂热相结合的方法,以树枝状金属Cd颗粒为模板和前驱体,在乙二胺溶剂中以六亚甲基四胺(HMTA)为表面修饰剂,制备出具有三维阵列结构的树枝晶CdS。利用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)结合X射线能谱仪(EDS)等对样品的物相、形貌、元素组分和结构进行了分析。结果表明:在溶剂热反应过程中,当不加入HMTA时,得到的产物是无序的CdS纳米线;而在HMTA的作用下,则生成的是具有三维阵列结构的树枝晶CdS;通过分析溶剂热反应过程中的化学反应,并结合产物形貌演变规律,提出了具有三维阵列结构的树枝晶CdS的形成机理。光催化性能测试表明具有三维树枝晶CdS纳米阵列在可见光照射下表现出良好的光催化活性。     

Determination of phthalate esters from environmental water samples by micro‐solid‐phase extraction using TiO2 nanotube arrays before high‐performance liquid chromatography

We describe a highly sensitive micro‐solid‐phase extraction method for the pre‐concentration of six phthalate esters utilizing a TiO₂ nanotube array coupled to high‐performance liquid chromatography with a variable‐wavelength ultraviolet visible detector. The selected phthalate esters included dimethyl phthalate, diethyl phthalate, dibutyl phthalate, butyl benzyl phthalate, bis(2‐ethylhexyl)phthalate and dioctyl phthalate. The factors that would affect the enrichment, such as desorption solvent, sample pH, salting‐out effect, extraction time and desorption time, were optimized. Under the optimum conditions, the linear range of the proposed method was 0.3–200 μg/L. The limits of detection were 0.04–0.2 μg/L (S/N = 3). The proposed method was successfully applied to the determination of six phthalate esters in water samples and satisfied spiked recoveries were achieved. These results indicated that the proposed method was appropriate for the determination of trace phthalate esters in environmental water samples.     

ZnO纳米棒阵列基-芴类共轭聚合物膜的制备及对TNT的检测评价

将共轭芴类荧光聚合物涂覆在纳米Zn O棒阵列上,制成荧光传感膜检测痕量TNT。通过水热法生长的Zn O纳米棒阵列具有较好的取向性,作为衬底可有效增大荧光膜荧光强度,同时,Zn O纳米棒阵列的高比表面积可提高膜对TNT气体的响应效率,使20s内的荧光猝灭率可达72%。     

气液界面胶体球刻蚀法制备二维有序多孔薄膜

作为一类重要的二维材料, 二维有序多孔薄膜受到人们的广泛关注. 气液界面胶体球刻蚀法是近些年发展起来的一种以漂浮在液面上的单层胶体晶体为模板来制备二维有序纳米结构的方法, 具有简单、高效、重现性好、适用范围广以及结构参数易调变等优点. 近年来, 我们课题组利用气液界面胶体球刻蚀法实现了包括多种无机物纳米网、纳米碗阵列和纳米网-纳米碗复合阵列在内的一系列自支撑二维有序多孔薄膜的可控制备, 考察了其二维光子晶体性质, 并研究了其在刻蚀掩膜、溶剂检测、生物传感、电阻开关器件、光电化学分解水等方面的应用. 本文在重点介绍我们课题组研究进展的同时, 也简要总结了该领域的整体发展状况并展望了该领域的今后发展方向.