Separate Polarization Modes Synchronization and Synchronization Switches between Vertical-Cavity Surface-Emitting Lasers

For vertical-cavity surface-emitting lasers (VCSELs) with polarization-rotated feedback, there exist several synchronization types such as synchronizations between total powers and synchronizations between separate polarization modes. Based on the two-mode rate equations, we study and compare numerically the performances of different synchronization types. Our results show that three synchronization types exhibit good performances when their synchronization conditions are satisfied. They are the complete synchronization between total powers, complete synchronization between x-polarized modes, and generalized synchronization between x-polarized and y-polarized modes. The former two types are sensitive to the injection rate and spontaneous emission, while the third type is contrary. Synchronization type with the best performance may switch from one to another, with changing of injection rate and spontaneous emission factor.     

Surface and interfacial properties of PVDF/acrylic copolymer blends before and after UV exposure

Morphological and chemical properties of both the surface and interface of poly(vinylidene fluoride)/poly(methyl methacrylate)-co-poly(ethyl acrylate) (PVDF/PMMA-co-PEA) blend films have been investigated before and after the samples were exposed to ultraviolet (UV) irradiation using a xenon arc lamp at 50 °C and 9% relative humidity (RH) for 7 months. Surface and interfacial morphologies were studied by atomic force microscopy (AFM). Chemical composition information was obtained by confocal Raman microscopy, attenuated total reflection-FTIR spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), and contact angle measurements. Results show an enrichment of the PVDF material at the air surface, while the acrylic copolymer enriches the interface. Blends having greater than 50% mass fraction of PVDF show little change in the surface morphology after UV exposure for 7 months. However, for a lower PVDF content, blends exhibit significant degradation of PMMA-co-PEA copolymer and a much rougher surface after UV exposure. Microstructural changes in the PVDF spherulites are also observed after UV degradation. It is found that the surface and interfacial morphologies are correlated with the chemical properties.     

Mode beating in spot-size converter lasers

An anomalous modulation in the wavelength spectrum has been observed in lasers with spot-size converters. This intensity modulation is shown to be caused by beating between the fundamental lasing mode and radiation modes in the taper. This results in a periodic modulation in the net gain spectrum, which causes wavelength jumps between adjacent net gain maxima, and a drive current dependent spectral width that is expected to affect system performance. The amplitude of this spectral modulation is reduced significantly by either using an angled rear-facet which reflects the beating radiation modes away from the laser axis, or by using a nonlinear, adiabatic taper.     

The Properties of Light Pressure Force with High Order in Laser Fields

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｉｎｒｅｃｅｎｔｙｅａｒｓ,ｂｏｔｈｔｈｅｔｈｅｏｒｅｔｉｃａｌａｎｄｅｘｐｅｒｉｍｅｎｔａｌｉｎｖｅｓｔｉｇａｔｉｏｎｓｏｎｌａｓｅｒｃｏｏｌｉｎｇａｎｄｔｒａｐｐｉｎｇｈａｖｅｂｅｃｏｍｅｏｎｅｏｆｔｈｅｍａｊｏｒｆｉｅｌｄｓｉｎａｔｏｍｉｃ,ｍｏｌｅｃｕｌａｒａｎｄｏｐｔｉｃａｌ ｐｈｙｓｉｃｓ[1～ 8] .Ｔｈｅｄｅｖｅｌｏｐｍｅｎｔｏｆｌａｓｅｒｃｏｏｌｉｎｇａｎｄｔｒａｐｐｉｎｇｔｅｃｈｎｏｌｏｇｙｉｓｉｍｐｏｒｔａｎｔｆｏｒｔｈｅａｐｐｌｉｃａｔｉｏｎｓｓｕ…     

Pulsed laser deposition of nanostructured Ag films

Ultra-thin (0.5-5 nm) films of Ag have been prepared by pulsed laser deposition in vacuum using a 26 ns KrF excimer laser at 1 J cm⁻². The deposition was controlled using a Langmuir ion probe and a quartz crystal thickness monitor. Transmission electron microscopy showed that the films are not continuous, but are structured on nanometer size scales. Optical absorption spectra showed the expected surface plasmon resonance feature, which shifted to longer wavelength and increased in strength as the equivalent film thickness was increased. It is shown that Maxwell Garnett effective medium theory can be used to calculate the main features of optical absorption spectra.     

Surface polarity of cellulose derivates observed by coumarin 151 and 153 as solvatochromic and fluorochromic probes

Solvent‐dependent ultraviolet–visible (UV–vis) absorption and Stokes shifts including strong hydrogen‐bond‐donating (HBD) solvents such as 2,2,2‐trifluoroethanol and 1,1,1,3,3,3‐hexafluoro‐2‐propanol of two coumarine dyes (Co 151 and Co 153) were analyzed with multiple‐square analyses of linear solvation energy relationships and the Kamlet–Taft solvent parameter set to α (HBD capacity), β (hydrogen‐bond‐accepting capacity), and π* (dipolarity/polarizability). The UV–vis absorption and emission spectra of Co 151 and Co 153 were measured when adsorbed on various polysaccharides such as different cellulose batches, carboxymethylcelluloses with different degrees of substitution, and chitine. As a result of this evaluation, Co 153 is recommended as an alternative UV–vis probe for evaluating the dipolarity/polarizability of cellulose and cellulose derivates. Multiple adsorption of Co 153 on Linters cellulose took place indicating a wide‐surface polarity distribution, which makes the determination of a rigid polarity parameter questionable. Thus, fluorescence measurements of adsorbed Co 153 are suitable to detect inhomogenities on a surface but not for the determination of empirical polarity parameters. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1210–1218, 2003     

Laser spectroscopic investigation of a new precursor-type polyparaphenylenevinylene

Optical, structural and morphological properties of thin films of polyparaphenylenevinylene (PPV) formed by an alkyl sulfinyl precursor route have been studied. Thin films were fabricated on an optical glass and on quartz glass either by spin-coating of the precursor solution or by layer-by-layer deposition using Langmuir–Blodgett technique. PPV precursor films were also spin-coated on gold-coated glass in order to study thin-film optical parameters by surface plasmon spectroscopy. We have been successful in forming about 40 precursor mono layers on quartz glass by Langmuir–Blodgett technique using optimized surface pressure and dipping conditions. After thermal conversion of the precursor layers good quality fluorescent PPV films of yellow colour have been obtained. Optical characterization of the films was carried out by linear absorption and emission spectroscopy, ellipsometry, and surface plasmon spectroscopy. Structural and morphological studies on the thin films were carried out by using X-ray scattering and atomic force microscopy. Wave-guided travelling-wave laser action has been achieved in a PPV film on quartz glass. The sample was transversally pumped with picosecond laser pulses (wavelength 347.15 nm, duration 35 ps). Laser emission occurred at 550 nm for pump pulse energy densities above .     

Photochemical Reactions of Protein Tryptophanyls in the Eye Lenses of Rats in the Presence of Chloroform

The modifying action of chloroform on photochemical reactions induced in the eye lenses of rats by UVB radiation is revealed. In anesthetic concentrations, halogenmethane increases the quantum yield of photodisintegration of protein tryptophanyls with formation of a new photochemical product that absorbs radiation in the UVA range and possesses the photosensitizing activity.     

Changes in the Laser-Induced Fluorescence Spectrum of Myocardium Tissue with Decrease in Its Viability

We investigated the laser-induced fluorescence spectra (LIF) of porcine cardiac tissues with different degrees of viability. The data obtained are compared with the results of routine histological investigations and also with the experiments performed with the use of fluorescent probes. It has been found with a high degree of reliability that the loss of the viability of the myocardium tissue leads to the alteration of its LIF spectra. This can be used for low-invasive rapid control of transplant viability in the process of its preparation and during surgery.     

Submicrometric Displacement and Vibration Measurement Using Optical Feedback in a Fiber Laser

A very simple and efficient technique for the remote sensing of a noncooperative target is presented. This technique is based on the frequency-shifted reinjection of light in a class B laser. Ytterbium- and erbium-doped fiber lasers have both been used to measure displacements with a submicrometric resolution and the vibration power spectrum of an object.