氧化石墨烯调控钼酸铋在可见光下选择性光催化降解环境水中的抗生素

以氧化石墨烯(GO)作为增强光催化剂活性的调节剂, 采用一步水热法制备钼酸铋/氧化石墨烯(Bi₂MoO₆/GO)异质结光催化剂, 其可见光响应拓展至570 nm, 带隙能降至2.56 eV. 当m_Bi2MoO6/m_GO=100∶1时, Bi₂MoO₆/GO(100∶1)光催化剂在可见光的辐射下, 对水溶液中四环素和喹诺酮类抗生素选择性的高效催化降解去除能力为Bi₂MoO₆的2.1倍. Bi₂MoO₆/GO(100∶1)光催化剂活性的提高依赖于范德华力作用下的二维Bi₂MoO₆纳米片-二维GO纳米片界面的紧密接触. 有效的界面接触改善了光生电子的转移和光生载流子的分离. 自由基清除实验结果表明, ?OH起主要作用. 结合高效液相色谱-质谱(HPLC-MS)法对降解产物的分析, 提出了不同光催化剂催化降解恩诺沙星具有相似的降解途径和降解产物.     

ZnCl2、KOH和HNO3改性MWCNT对苯酚的吸附行为研究

通过扫描电子显微镜、X射线衍射仪、N₂吸附分析仪及Boehm滴定法获得ZnCl₂、KOH和HNO₃化学处理对高纯多壁碳纳米管的结构和表面含氧官能团的影响,通过批处理实验考察吸附条件（吸附时间、初始浓度、温度）对处理前后的碳纳米管吸附苯酚行为的影响,并采用准一级、准二级、Evolich动力学模型和热力学方程拟合其吸附数据,分析其动力学行为、热力学行为和吸附机理。结果表明,虽然ZnCl₂、KOH和HNO₃化学处理法均未对碳纳米管BET比表面积产生显著影响,但会影响其表面化学性质（即,对于ZnCl₂和KOH化学处理降低表面羧基、内酯基含量和增大碱性官能团量,而对于HNO₃化学处理可以增大表面羧基、内酯基含量,而碱性官能团略有增加）;改性处理影响碳纳米管去除苯酚效率：由于ZnCl₂和KOH改性处理降低碳纳米管表面羧基量,故其提高了苯酚去除率,而HNO₃处理则略减小碳纳米管的苯酚去除率,可能是由于碳纳米管结构和表面化学性质共同影响所致;碳纳米管的苯酚去除率均随苯酚溶液初始浓度的增大而减小;高温不利于吸附;热力学研究发现碳纳米管吸附苯酚过程是自发的和放热的,属于物理吸附;动力学研究表明,吸附过程符合准二级动力学方程。通过ZnCl₂和KOH化学处理,可以显著提高碳纳米管对苯酚的吸附性能。     

Ni-Co、Ni-Cu双金属合金催化剂用于CO甲烷化

以钙钛矿型复合氧化物LaNi_(0.9)Co_(0.1)O_3和LaNi_(0.9)Cu_(0.1)O_3为前驱体制备了Ni-Co/La_2O_3和Ni-Cu/La_2O_3双金属合金催化剂。结果表明,双金属合金催化剂中,各组分间相互稀释,具有较强的抗烧结性能;催化剂表面的积炭主要取决于CO在催化剂表面的吸附形态,Ni-Co双金属催化剂中,Co掺杂改变了CO在催化剂表面的吸附形式和吸附强度,使得Ni-Co双金属催化剂具有较强的抗积炭性能。Ni-Co双金属合金催化剂用于CO甲烷化反应时,显现出较好的活性、选择性和稳定性。     

碳化终温对β-Mo2C催化喹啉加氢脱氮性能影响

以MoO_3为前驱物,CH_4/H_2为碳源,采用程序升温直接还原碳化法制备不同碳化终温(640、660、680、700和720℃)的碳化钼催化剂,通过XRD、N_2吸附-脱附、SEM、TEM、XPS和Raman表征研究碳化钼的物理性质和结构性质,并研究不同碳化终温碳化钼对喹啉加氢脱氮的催化性能。结果表明,不同碳化终温的碳化钼催化剂均为β-Mo_2C,碳化终温可显著改变碳化钼表面物种含量、平均孔径和介孔分布。碳化终温为680℃时,催化剂碳化程度较高,表面氧物种含量最低,表面C/Mo物质的量比最高,对应的催化活性也最佳,在340℃、4 MPa条件下,喹啉的转化率和脱氮率均高达99%以上,芳香族类化合物的选择性可达37.8%,显示出较低的芳环破坏性。表面组成尤其是表面氧对于β-Mo_2C上喹啉加氢脱氮反应途径的调控至关重要。     

Electrochemical codeposited polypyrrole–tungsten oxide composite materials with wide potential windows

The three-dimensional morphology has sufficient interface contact and can be in favor of the electronic transport process. In this work, the demand for high-performance electrodes such as energy storage devices has been designed. Polypyrrole and tungsten oxide composite materials (PPy-WO₃) have been synthesized by cyclic voltammetry (CV) technology at −0.6 to 0.9 V versus saturated calomel electrode (SCE) for 20 cycles. The PPy-WO₃^{20 mV/s}, PPy-WO₃^{60 mV/s}, and PPy-WO₃^{120 mV/s} electrodes have been prepared by CV technology at sweep rates of 20, 60, and 120 mV/s. The influences of scan rate on morphologies and charge storage properties of the composites are discussed. Among them, a three-dimensional flake structure for PPy-WO₃^{20 mV/s} with a size of up to several micrometers was synthesized. PPy-WO₃^{20 mV/s} composites as electrode materials exhibit a wide charge storage potential window of 1.4 V (between −0.9 and 0.5 V vs. SCE) and a specific capacitance of 145.13 F/g at 1 mA/cm². Moreover, the long-term stability of PPy-WO₃^{20 mV/s} and PPy has been investigated in 5 M LiCl aqueous electrolyte. The stability of the materials can be improved by inorganic and organic composites.     

RuII and RuIII Chloronitrile Complexes: Synthesis,Reaction Chemistry,Solid State Structure,and (Spectro)Electrochemical Behavior

The synthesis of [Ti₆O₄(OiPr)₈(O₂CPh)₈] ( 3 ) and [RuCl(N≡CR)₅][RuCl₄(N≡CR)₂] ( 4a , R = Me; 4b , R = Ph), [Ru(N≡CPh)₆][RuCl₄(N≡CPh)₂] ( 5 ) and [H₃O][RuCl₄(N≡CMe)₂] ( 7a ) is discussed. Crystallization of 5 from CH₂Cl₂ gave trans-[RuCl₂(N≡CPh)₄] ( 6 ). The solid-state structures of 3 , 4a , b , 5 , 6 and 7a are reported. Complex 4b forms a 3D network, while 6 displays a 2D structure, due to π-interactions between the benzonitrile ligands. The (spectro)electrochemical behavior of 4a , b and 6 was studied at 25 and –72 °C and the results thereof are compared with [NEt₄][RuCl₄(N≡CMe)₂] ( 7b ) and [RuCl(N≡CPh)₅][PF₆] ( 8 ). The electrochemical response of the cation and the anion in 4a , b are independent from each other. [RuCl(N≡CR)₅]⁺ possesses one reversible Ru^II/Ru^III process. However, [RuCl₄(N≡CMe)₂]^– was shown to be prone to ligand exchange and disproportionation upon formation of either a Ru^IV and Ru^II species at 25 °C, while at –72 °C the rapid conversion of the electrochemically formed species is hindered. In situ IR and UV/Vis/NIR studies confirmed the respective disproportionation reaction products of the aforementioned oxidation and reduction, respectively.     

Facile Synthesis of MOF-derived Mn3O4@N-doped Carbon with Efficient Oxygen Reduction

Integration of MnO_x into the carbon matrix proves a viable strategy to improve the electrochemical performance of MnO_x materials. Mn₃O₄ nanoparticle-decorated N-doped carbon composites (Mn₃O₄@N-doped carbon) were facilely prepared from a non-porous eight-fold interpenetrated Zn^II-based MOF, which involves first synthesis of bimetallic Mn/Zn-MOF in one-pot reaction followed by direct pyrolysis at 1000 °C. In 0.1 m KOH solution, the optimal Mn₃O₄@N-doped carbon exhibits decent oxygen reduction activity with the onset potential (E_onset) of 0.94 V (vs. RHE) and half-wave potential (E_1/2) of 0.81 V (vs. RHE), excellent methanol tolerance as well as good durability.     

Synthesis and Assembly of Zinc Oxide Microcrystals by a Low-Temperature Dissolution–Reprecipitation Process: Lessons Learned About Twin Formation in Heterogeneous Reactions

Cobalt-doped zinc oxide single crystals with the shape of hexagonal platelets were synthesized by thermohydrolysis of zinc acetate, cobalt acetate, and hexamethylenetetramine (HMTA) in mixtures of ethanol and water. The mineralization proceeds by a low-temperature dissolution–reprecipitation process from the liquid phase by the formation of basic cobalt zinc salts as intermediates. The crystal shape as well as twin formation of the resulting oxide phase can be influenced by careful choice of the solvent mixture and the amount of doping. An understanding of the course of the reaction was achieved by comprehensive employment of analytical techniques (i.e., SEM, XRD, IR) including an in-depth HRTEM study of precipitates from various reaction stages. In addition, EPR as well as UV/Vis spectroscopic measurements provide information about the insertion of the cobalt dopant into the zincite lattice. The Langmuir–Blodgett (LB) technique is shown to be suitable for depositing coatings of the platelets on glass substrates functionalized with polyelectrolyte multilayers and hence is applied for the formation of monolayers containing domains with ordered tessellation. No major differences are found between deposits on substrates with anionic or cationic surface modification. The adherence to the substrates is sufficient to determine the absolute orientation of the deposited polar single crystals by piezoresponse force microscopy (PFM) and Kelvin probe force microscopy (KPFM) studies.     

纳米银/二维石墨相氮化碳/还原氧化石墨烯复合材料的制备及其光催化降解抗生素

为优化石墨相氮化碳(g-C₃N₄)光催化剂的结构,改善其对污染物的降解性能,本文以三聚氰胺为前驱体,通过高温煅烧和热氧化剥离制备了二维石墨相氮化碳(2D-C₃N₄),并用光还原法一步合成纳米银/二维石墨相氮化碳/还原氧化石墨烯(Ag/2D-C₃N₄/rGO)复合光催化剂。通过X射线粉末衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、紫外-可见漫反射光谱(UV-Vis DRS)、光致发光光谱(PL)、X射线光电子能谱(XPS)、氮气吸附脱附等温曲线(BET)等对材料进行表征。 以头孢曲松钠为目标污染物,探究pH值、催化剂用量、头孢曲松钠初始浓度等因素对催化剂的吸附、降解性能的影响,并探究降解反应机理。 当pH=6.0,催化剂用量为0.3 g/L,头孢曲松钠初始浓度为10.0 mg/L时,复合材料对头孢曲松钠的降解率可达到89.1%。 催化剂的稳定性较强,具有实际应用价值,可用于处理含头孢类抗生素的废水。     

无电沉积法AuNPs-MWCNTs的制备及其对黄酮类化合物的电化学催化性能研究

利用多壁碳纳米管具有较低的还原电位,以多壁碳纳米管作为还原剂和负载基底,通过无电沉积法制备了负载纳米金粒子的碳纳米管催化剂。此种材料具有更多的活性位点,避免了纳米金粒子表面保护剂的存在造成其催化活性降低的缺陷,发现其对典型黄酮类化合物-芦丁和黄芩苷具有良好的电化学催化性能和较高的灵敏度,并将其应用于电化学分析检测黄酮类化合物。