Sol-gel polyimide-silica composite membrane: gas transport properties

The effect of introduction of silica particles prepared by the sol-gel technique on the gas transport properties of a polyimide film was studied. The sorption and permeation of N₂, O₂, CO₂, H₂ and CH₄ were studied and correlated with morphological changes in the polymer structure. From sorption isotherms, we observed that the composite membrane presents higher solubility coefficients than the polyimide one. The solubility coefficient ratio between the composite and the polyimide is about 1.5–2.0. The isotherms were analyzed in terms of the dual mode sorption. The Henry's coefficient and the Langmuir's affinity and saturation constants were obtained allowing to calculate the Langmuir to Henry concentration ratios as function of the gas pressure. These ratios decrease until zero within a certain pressure range as long as the Langmuir's mode is acting and they are higher for the polyimide membrane when compared with the composite one. This study was completed with calorimetric measurements during the sorption. The gas interaction energy in kJ/mol decreases within the same pressure range as previously described. The measured energies are higher for the polyimide film when compared with the composite one because the polyimide membrane presents a stronger energetic effect caused by a higher Langmuir's contribution. From permeation studies at 3.15⁵ Pa, the composite membrane showed higher permeability coefficients and permselectivities than the polyimide one. All these results were explained, taking into account the difference on the imidization degree of both membranes and the morphological changes which may be induced by the silica nodules in the organic/inorganic interphases.     

互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体，水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂），制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM），透射电镜（TEM），X射线衍射（XRD），热重分析（TGA）对其结构进行表征；采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面，形成多层次结构，并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构；MnO₂纳米片具有典型的K-Birnessite 型晶体结构；复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1；随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极，活性炭（AC）为负极，1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器，发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V，容量可达86F·g^-1，且表现出良好的电容特性和大电流放电性能.     

Fine characterization of the ethylene and ethane sorption in poly(amide 12-block-tetramethylenoxide) copolymer/AgBF4 membranes

Ethylene/ethane sorption characteristics were determined for dry Pebax™ (poly(amide 12-block-tetramethylenoxide) copolymer)/AgBF₄ membranes by using an electronic microbalance. The membranes containing 0.7 and 22 wt.% AgBF₄ showed a dual-mode sorption isotherm. The ethane isotherms for all the membranes were of the Henry-type, which is the normal sorption for gases in rubbery polymers. The abnormal presence of Langmuir sorption sites only for ethylene in the rubbery copolymer, never reported sofar, is attributed to the silver-based specific complexation sites. The silver salt which dissolved in limited amounts in the rubbery copolymer had a much smaller Langmuir sorption capacity than the salt that crystallized in the copolymer. The sorption kinetics indicate that the crystallized salt did adsorb slowly ethylene according to a zeroth-order kinetics, but not ethane. The gas uptake kinetics resulting from a step of the pressure surrounding the copolymer exhibited one stage for ethane but two stages for ethylene. For the latter, there was first a fast Fickian sorption stage, then a drift of the zeroth-order sorption of ethylene on salt crystals, which contributes for a large part to the total uptake. The zeroth-order sorption suggests that the sorbed ethylene amount in the second-stage is independent of the crystal-surface coverage. The value of the Fickian diffusion coefficient calculated by fitting the kinetics with a solution of the second Fick’s law was 5 × 10⁻¹² m²/s for both ethylene (the first stage) and ethane, and is typical for small organic compounds in a rubbery material.     

Molecular imprinting in ultrathin titania gel films via surface sol-gel process

Recent progresses of molecular imprinting in metal oxide matrices were summarized. Application of the surface sol-gel process to mixtures of organic carboxylic acids and titanium alkoxide provides ultrathin layers of titania gel (10-20 nm thick), in which molecule-sized cavities are kept intact upon removal of the organic templates. The imprinted cavity reflects the structural and functional features of the template molecule, and the enantioselective imprinting of dipeptide isomers is observed. Robustness and flexibility of the ultrathin titania layer is demonstrated by the formation of interconnected titania hollow structures. Possible practical applications and unsolved problems of this technique are discussed.     

Pervaporation of ethanol-water mixtures through temperature-sensitive poly(vinyl alcohol-g-N-isopropyacrylamide) membranes

Novel temperature-sensitive membranes have been synthesized by grafting poly(N-isopropyacrylamide) (poly(NIPAAm)) onto a poly(vinyl alcohol) (PVA) backbone using hydrogen peroxide-ferrous ion as initiator. Due to the grafting of poly(NIPAAm), the hydrophilic/hydrophobic balance and the polarity of the pendent groups within the membranes are modified. Significant temperature sensitivity of the grafted membranes is observed close to the LCST of linear poly(NIPAAm) in the pervaporation processes for ethanol-water separation. Both the pervaporation and sorption selectivities for water show a maximum value in the vicinity of 30–32°C for an ethanol content of 75 and 80%. The temperature sensitivity of the grafted membranes also depends on the ethanol concentration. The maxima of pervaporation and sorption selectivities disappear when the ethanol content is lower than 75% because the much larger degree of swelling reduces the size screening effect of the membranes.     

Effect of solution chemistry on the surface charge of polymeric reverse osmosis and nanofiltration membranes

A streaming potential analyzer has been used to investigate the effect of solution chemistry on the surface charge of four commercial reverse osmosis and nanofiltration membranes. Zeta potentials of these membranes were analyzed for aqueous solutions of various chemical compositions over a pH range of 2 to 9. In the presence of an indifferent electrolyte (NaCl), the isoelectric points of these membranes range from 3.0 to 5.2. The curves of zeta potential versus solution pH for all membranes display a shape characteristic of amphoteric surfaces with acidic and basic functional groups. Results with salts containing divalent ions (CaCl₂, Na₂SO₄, and MgSO₄) indicate that divalent cations more readily adsorb to the membrane surface than divalent anions, especially in the higher pH range. Three sources of humic acid, Suwannee River humic acid, peat humic acid, and Aldrich humic acid, were used to investigate the effect of dissolved natural organic matter on membrane surface charge. Other solution chemistries involved in this investigation include an anionic surfactant (sodium dodecyl sulfate) and a cationic surfactant (dodecyltrimethylammonium bromide). Results show that humic substances and surfactants readily adsorb to the membrane surface and markedly influence the membrane surface charge.     

Sol-gel processing of inorganic membranes

Basic principles involved in sol-gel processing of ceramic membranes are described. This process has been applied to ceramic ultrafiltration membranes and is now investigated to prepare ceramic nanofilters. In this paper special emphasis is put on new developments concerning microporous zirconia membranes obtained by the polymeric route. A zirconium alkoxide precursor modified with an acetylacetone ligand has been used in order to control particle growth in the sols and pore size distribution in the membranes. N₂ adsorption and X-ray diffraction analysis have been performed on membrane materials showing the influence of process parameters (molar ratio r = acacH/Zr and sintering temperature T) on membrane structural evolution.     

Sol–gel preparation and properties of hydroxypropylcellulose–titania hybrid thin films

Hydroxypropylcellulose (HPC)–titania hybrid thin films were prepared by sol–gel method where titanium tetraisopropoxide Ti(OC₃H₇ ⁱ )₄ was hydrolyzed under acidic conditions in the presence of HPC, followed by dip-coating and drying at 120 °C for 24 h. The viscosity average molecular weight of HPC was 55,000–70,000 or 110,000–150,000, and the TiO₂/(HPC + TiO₂) mass ratio ranged from 0 to 1, which was calculated on the assumption that all Ti(OC₃H₇ ⁱ )₄ is converted into TiO₂. The films were 0.35–1.0 μm thick, transparent in visible region and opaque in ultraviolet (UV) region, where the optical absorption coefficient in UV region increased with increasing titania content. The refractive index increased with increasing titania content, ranging from 1.6 to 1.8 for the hybrid thin films. The pencil hardness increased from 6B to 5H, the durability in hot water significantly increased and the contact angle of water on films increased from 35° to 89° with increasing titania content. Crack-free films could be deposited on organic polymer substrates irrespective of titania or HPC contents, where cracking did not occur at higher HPC contents even when the substrate was bent.     

Electrochemistry of capillary systems with narrow pores. IV. Dialysis potentials

The dialysis potentials of different collodion membranes with graded pore sizes and electrochemical activities have been measured in dilute aqueous KCl solutions as functions of concentration. It is possible to predict the value of the diffusion potential within a few millivolts on the basis of electrical conductivity data obtained with the same membranes. In general, the measured values are lower than those calculated. It is assumed that this difference is caused by the membranes having a distribution of pore sizes.     

Microfiltration of protein solutions at thin film composite membranes

An experimental study of the interaction of the enzyme yeast alcohol dehydrogenase (YADH) with polysulfone thin film composite microfiltration membranes (Dow-Danmark) has been carried out. It was found that the membranes adsorbed only 3/4 of a monolayer of the enzyme under the conditions studied. Even so, under filtration conditions, the membrane permeation rate decreased continuously with time. This decrease in permeation rate was due neither to concentration polarisation nor to protein adsorption alone. However, it could be quantified using the standard blocking filtration law, which describes a decrease in pore volume due to deposition of protein in the interior structure of the membrane. Reversal of the membrane, so that the supporting matrix faced the feed solution, gave more stable permeation rates. Implications for the microfiltration of industrial fermentation broths are discussed.