溅射功率对直流磁控溅射Ti膜结构的影响

 采用直流磁控溅射方法制备了纯Ti膜,研究了不同功率下Ti膜的沉积速率、表面形貌及晶型结构,并对其应力进行了研究。研究表明：薄膜的沉积速率随溅射功率的增加而增加,当溅射功率为20 W时,原子力显微镜(AFM)图像显示Ti膜光洁、致密,均方根粗糙度最小可达0.9 nm。X射线衍射(XRD)分析表明薄膜的晶体结构为六方晶型,Ti膜应力先随溅射功率增大而增大,在60 W时达到最大值（为945.1 MPa）,之后随溅射功率的增大有所减小。     

钛扩散铌酸锂矩形波导中的双折射耦合对传播常数的影响

 从亥姆霍兹方程出发，得到了各向异性光波导在弱导近似下的耦合模理论。耦合系数包括偏振耦合项和双折射耦合项。并用马卡提里近似下的模式作为零级近似。用一级微扰法计算了折射率渐变分布的钛扩散铌酸锂矩形波导的传播常数。在给定参数的情况下，得到双折射项引起的传播常数的改变约为主微扰项的3%，因此双折射耦合对钛扩散铌酸锂矩形波导的性能影响不可忽略，这对设计和分析与它相关的光波导器件具有指导意义。     

双齿配位过渡金属化合物化学——Ⅲ.钒的邻巯基苯酚配合物的顺磁谱研究

测定了二个顺磁性化合物(Ph_1P)[V_2(mp)_6](Ⅰ)和(Ph_4P)_2[NaV(mp)_3 (MeCN)(MeOH)](Ⅱ)(H_2mp=邻巯基苯酚,o-HO_1C_6H_4SH)的固态和/或溶液中的顺磁波谱。(Ⅰ)的77K固态谱及(Ⅱ)的室温固态谱均经模拟计算,认为它们的钒原子处在S=l/2的Ⅰ=7/2状态,(Ⅱ)的低温(77K)溶液谱(乙腈)与Ⅱ的固态谱相同,均有特征的八条精细结构,认为非配对电子基本上定域在钒原子的周围。     

Ultrasound-assisted of alkali chloride separation using bulk ionic liquid membrane

An ultrasonic-assisted separation of alkali chloride (LiCl, NaCl, and KCl) salts have been carried out using of an hydrophobic ionic liquid membrane (ILM). The ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate and tributyl phosphate mixture have been used as ILM. An ultrasonic probe with different frequencies (25, 100, and 250) kHz have been applied as source of ultrasound generator with different times of sonication (2, 5, and 10) min in three phases system containing feed, ILM, and receiver in osmotic U-shaped tube. Also, 250, 500, and 1000 ppm of the feed (alkali chloride) concentration have been used to separate. The frequency of 250 kHz with higher sonication time provides optimum condition for separation of LiCl with lower feed concentration. The thermodynamic properties such as density and speed of sound and the related thermodynamic properties have been calculated to optimize ILM composition (x_IL = 0.45) for ultrasound-separation.     

CaCu3Ti4O12 陶瓷介电模量响应特性的研究

由于CaCu₃Ti₄O₁₂巨介电常数陶瓷的低频区直流电导较大, 本文采用模量 M"-f频谱表征与分析了低频和高频的两个松弛极化过程. 研究认为, 这两个特征峰属于晶界区Schottky 势垒耗尽层边缘深陷阱的电子松弛过程, 其中高频松弛峰起源于晶粒本征缺陷的电子松弛过程, 而低频松弛峰则为与氧空位有关的松弛极化过程. 对于CaCu₃Ti₄O₁₂这类低频下具有高直流电导的陶瓷材料, 采用模量频谱能更有效地分析研究其损耗极化机理. 关键词： 3Ti₄O₁₂陶瓷')" href="#">CaCu₃Ti₄O₁₂陶瓷 模量 松弛过程 电导     

Molecular dynamic studies of the solubility of sodium chloride: fast calculations using seed crystalline cluster probe

Theoretical predictions of solubility, typically accomplished by comparing the chemical potential of pure solid and solution, currently suffer from a lack of accuracy. We suggest an alternative method for predicting solubility based on molecular dynamics simulations of the behaviour of a small seed crystalline cluster probe in solutions of varying concentrations. The size dynamics of a properly chosen seed cluster that dissolves in unsaturated solutions and grows in size in supersaturated solutions is indicative of the saturation point. This approach is illustrated by its application to NaCl in water.     

Effect of deposition power and pressure on rate deposition and resistivity of titanium thin films grown by DC magnetron sputtering

ABSTRACT

Based on magnetron sputtering deposition technology, titanium (Ti) thin films are deposited on silicon (Si) substrate using different preparation conditions such as sputtering power and pressure. The influence of altering these conditions on deposition rate and microstructure is studied. The results show that sputtering power significantly affects the rate of deposition and the resistivity. The deposition rate of the Ti thin film increases when the resistivity decreases under sputtering powers of 150–225?W with a pressure of 0.8?Pa and Argon (Ar) flux of 80 sccm. As sputtering power was increased further (from 225 to 250?W), the deposition rate reduced and the resistivity augmented. Pressure also has influence on the deposition rate and resistivity – when pressure increases from 0.6 to 0.8?Pa, the deposition rate escalates while the resistivity reduces; when the pressure is raised from 0.8 to 1.0?Pa with Ar flux of 100 sccm, the deposition rate decreases and resistivity increases. The surface chemical compositions and the structures of the Ti film were studied by using X-ray photoelectron spectroscopy (XPS) and X-ray diffractometer (XRD). Observing the cross-section of the thin-film samples produced by scanning electron microscope (SEM) reveals the influence of the preparation conditions used on the microstructure and confirms the influence of sputtering power and pressure on the resistivity.     

Flow‐Injection Online Reduction Atomic Fluorescence Spectrometry Determination of Se(IV) and Se(VI) with Electrochemical Hydride Generation

Abstract

A new flow‐injection online reduction electrochemical hydride generation system for the determination of Se(IV) and Se(VI) by atomic fluorescence spectrometry (AFS) was developed. In the system, an electromagnetic induction oven was used as heating resource to reduce Se(VI) to Se(IV) and a homemade tubular electrolytic cell as hydride generator. All analytical procedures were automatically controlled by a computer. The conditions of online reduction, including temperature, HCl concentration, and reduction time, have been studied in detail. The detection limits (3σ) of Se(IV) and Se(VI) in aqueous solution were 0.26 µg L^?1 and 0.23 µg L^?1, respectively. The precision for 11 replicate measurements of 50 µg L^?1 Se(IV) and Se(VI) was 2.2% and 2.5%. This proposed method has been applied to the determination of Se(IV) and Se(VI) in springwater samples.     

Flow Injection Kinetic Spectrophotometric Determination of Cerium Based on the Decolorization Reaction Between Arsenazo III and Cerium (IV)

ABSTRACT

Trace amounts of cerium were analyzed by flow injection kinetic spectrophotometry, based on the decolorization reaction between arsenazo III and Ce(IV) in sulfuric acid medium at room temperature. The absorbance difference (ΔA) of decolorization was linear with the concentration of Ce(IV). The flow injection technique was used to precisely control the timing. Under the optimum conditions, the determination of Ce(IV) in the range 0.0–8.0 µg mL^?1 with a correlation coefficient (r) of 0.9982, the regression equation was ΔA = 0.0014 + 0.0406c (µg mL^?1). The detection limit (3σ) of 0.2 µg mL^?1 was achieved at a sampling frequency of 60 h^?1. The proposed method was applied to the analyses of Ce in soil successfully.     

Determination of Chloride Content in Different Types of Cement Using Laser-Induced Breakdown Spectroscopy

The characterization and accurate determination of the chloride content in cement/concrete is very important for the assessment of the durability and safety of a concrete structure. The available analytical techniques are relatively expensive and time consuming. In this study, a laser-induced breakdown spectroscopy (LIBS) system was used for determination of elemental composition in three different types of cement samples. The plasma was generated by focusing a pulsed Nd: YAG laser at 1064 nm on the cement samples. The concentrations of different elements of significance for structural stability in cement samples were determined. The evaluation of the potential and the capabilities of LIBS as a rapid tool for characterization of cement samples is discussed. The optimum LIBS setup and experimental conditions to detect and measure chloride in building materials are reported. The LIBS results were compared with the results obtained using a standard analytical technique such as inductively coupled plasma emission spectroscopy (ICP–ES). The limits of detection were determined, and calibration curves were measured. The results of this investigation indicate the reliability of LIBS to characterize different cement samples and to assess the chloride content in these cements.