Sound velocity in different reacting thermal plasma systems

In most cases the energy dissipated in plasma jets used either,for heating or spraying is varied by changing the are current, the total gas floc+rate, and composition. However, when doing so, conditions are reached where the plasma jet may become supersonic. To predict such conditions or to characterize supersonic plasma jets the knowledge of the sound velocitya is mandatory The goal of this paper is to calculatea versus plasma forming gas composition, temperature, and pressure. Rigorous calculation would imply the knowledge of the chemical reaction kinetics, sound velocity depending strongly on this. Unfortunately such kinetics are generally lolknown for plasma jet floras and the only possibility is to determine the equilibrium sound velocitya calculated through the isentropic coefficient T. This coefficient has been calculated taking into account the dissociation and ionization reactions at equilibrium for temperatures ranging from 300 to 25,000 K and pressures between 0.1 and 1 Mpa for Ar, H₂, He, Ar-He, Ar-H₂, O₂, N₂, air, .steam, and methane.a often called the frozen sound velocity, was also calculated using (ratio of specific heats) instead of .     

用热分析技术测定碳化硅粉体对聚乙二醇的吸附量

用热分析技术TG-DTA(thermal gravimetric and differential thermal analysis)测定浆料中碳化硅粉体对分散剂聚乙二醇PEG(polyethylene glycol)的吸附量. 结果显示PEG在Ar气氛中411.5 ℃时完全分解; 碳化硅表面分散剂PEG的吸附量随着pH的增大而下降, 在较高pH下大多数分散剂仍存在于溶液中; 分散剂PEG的吸附量通过公式(1)进行计算. 该方法简单方便, 可以应用于测量氧化物或非氧化物吸附紫外-可见分光光度法不能测定的一些有机聚合物分子.     

Plasma Thermal Conversion of Methane to Acetylene

This paper describes a re-examination of a known process for the direct plasma thermal conversion of methane to acetylene. Conversion efficiencies (% methane converted) approached 100% and acetylene yields in the 90–95% range with 2–4% solid carbon production were demonstrated. Specificity for acetylene was higher than in prior work. Improvements in conversion efficiency, yield, and specificity were due primarily to improved injector design and reactant mixing, and minimization of temperature gradients and cold boundary layers. At the 60-kilowatt scale cooling by wall heat transfer appears to be sufficient to quench the product stream and prevent further reaction of acetylene resulting in the formation of heavier hydrocarbon products or solid carbon. Significantly increasing the quenching rate by aerodynamic expansion of the products through a converging–diverging nozzle led to a reduction in the yield of ethylene but had little effect on the yield of other hydrocarbon products. While greater product selectivity for acetylene has been demonstrated, the specific energy consumption per unit mass of acetylene produced was not improved upon. A kinetic model that includes the reaction mechanisms resulting in the formation of acetylene and heavier hydrocarbons, through benzene, is described.     

Na3Fe(C2O4)3·5H2O的热解过程和FAB-MS断裂规律

以红外光谱法为主要手段，原位“跟踪”测定铁（Ⅲ）与乙二酸形成的配合物Ｎａ３Ｆｅ（Ｃ２Ｏ４）３．５Ｈ２Ｏ的热解过程，分析了气、固相热解产物。并以色谱分析、差热－热重分析和Ｘ－射线粉末衍射法定性、定量地验证其结果。测定了该配合物快原子轰击质谱，提出了断裂规律。铁的二元羧酸配合物的质谱尚属首见。     

Thermal properties of rare earth dodecaborides

We have measured heat capacity and thermal expansion of rare earth dodecaborides REB₁₂ (RE=Y, Tb-Tm, Lu). YB₁₂ and LuB₁₂ are diamagnetics whereas the other dodecaborides are ordered antiferromagnetically. The amplitude of the heat capacity discontinuity at the Néel temperature and the shape of the heat capacity variation in the critical region for all these antiferromagnetics are characteristics for amplitude-modulated magnetic structures. In the ordered state TbB₁₂ reveals two first-order phase transitions, most likely due to magnetic structure changes. The heat capacity of ErB₁₂ just below the Néel point shows an anomaly of unclear origin. From the Schottky contribution to the heat capacity we have determined crystal field parameters. They are completely different than that is estimated from Point Charge Model.     

THERMAL PROPERTY, MISCIBILITY AND CRYSTALLIZATION BEHAVIOR OF POLY（3-HYDROXYBUTYRATE-co- 3-YDROXYHEXANOATE） AND POLY（BUTYLENE SUCCINATE-ADIPATE） （PHBHHX/PBSA） BLENDS

Blends of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHHx) and poly(butylene succinate-adipate) (PBSA), both biodegradable semicrystalline polyesters, were prepared with the ratio of PHBHHx/PBSA ranging from 80/20 to 20/80 by melt mixing method. Differential scanning calorimetry (DSC), thermogravimetry analysis (TGA), dynamic mechanical thermal analysis (DMA), polarizing optical microscopy (POM) and wide angle X-ray diffractometer (WAXD) were used to study the miscibility and crystallization behavior of PHBHHx/PBSA blends. Experimental results indicate that PHBHHx is immiscible with PBSA as shown by the almost unchanged glass transition temperature and the biphasic melt.     

Thermal degradation of copolymers of styrene with dicarboxylic acids - II: Copolymers obtained by radical copolymerisation of styrene with maleic acid or fumaric acid

Thermal degradation processes in copolymers of styrene with two stereoisomers of 1,2-ethylenedicarboxylic acids (i.e. maleic acid (the cis-isomer) and fumaric acid (the trans-isomer)) have been studied by mass spectrometry, FTIR and TG measurements. The influence of the chemical composition on thermal degradation of copolymers with acid by non-isothermal thermogravimetric analysis (TG) was also studied. The stereo-configuration of carboxyl groups in copolymers was analysed by potentiometric titration. It was found that copolymers degrade in two main complex stages. The initial step in the decomposition involves the formation of cyclic five-membered anhydrides. The presence of trans configuration of carboxyl groups hinders the formation of cyclic anhydrides and shifts the decomposition to higher temperatures, making decarboxylation competitive. At higher temperatures anhydride decomposition takes place and finally the degradation of main chains occurs.     

A Study on Thermal Decomposition of K_3[Fe(CN)_6] and KFe[Fe(CN)_6] in Helium

K3 [Fe(CN)6] and KFe[Fe(CN)6] are classical coordination compounds. However, the mechanism of decomposition reactions has not been well expounded. The gas products of thermal decomposition were examined by gas chroma tography (GC) , and the structure of the solid products by Mossbauer spectroscopy(MS) and X-ray diffraction(XRD). The findings are explained in terms of the theory of coordination chemistry and a decomposition mechanism is proposed in this study. On the basis of various experimental results, the first stage of the decomposition of K3[Fe(CN)6] in He was found to be the evolution of(CN)2 resulting in the reduction of Fe(Ⅲ)12K3 [Fe(CN)6]→9K4[Fe(CN)6] + Fe2 [Fe(CN)6] + 6 ( CN )For KFe [Fe(CN) 6 ], the first stage of decomposition man be represented as6KFe[Fe(CN)6]→3K2Fe[Fe(CN)6] + 2Fe2[Fe(CN)6 + 3(CN)2At higher temperatures, the decomposition of both K3[Fe(CN)6) andKFe[Fe(CN)6] to form KCN and Fe2C was accomplished by the release of(CN)2 and N2.     

Solubilities,thermostabilities and flame retardance behaviour of phosphorus-containing flame retardants and copolymers

Thirteen phosphorus-containing flame retardants were synthesized in this work. The solubilities of flame retardant [(6-oxide-6H-dibenz[c,e][1,2]oxaphosphorin-6-yl)-methyl]-butanedioic acid (DDP) in selected solvents are measured. TGA measurements of the 13 phosphorus-containing flame retardants were carried out and thermal stabilities of three flame-resistant PET (FRPET) resins were investigated. A FRPET incorporated by DDP with terephthalic acid and ethylene glycol reported in literature was also discussed and compared. The thermal stability of the FRPET is improved by the incorporation of phosphorus-containing flame retardants. The LOI values of all phosphorus-containing polyesters are higher than 27%. The improvement of the flame-resistant ability is due to the formation of the char that is not only caused by the existence of phosphorus elements in the resin but also by the relative large number of carbon atoms of the phenyl group in the flame retardants.     

固相热分解反应最可几机制的判断

固相热分解反应最可几机制的判断高永煜，邹文樵，冯仰婕（华东理工大学化学系上海２００２３７）关键词热分解，动力学方程，反应机制固相热分解反应机制的判断，是热分析动力学中令人感兴趣的领域。常用的方法是从含机制函数的非等温积分动力学方程出发，分别用Ｓｅｓｔ...