Resistivity and Thermal Expansion (4.2–820 K) of Skutterudites after Severe Plastic Deformation via HPT

Thermoelectric materials with a high figure of merit, ZT, are the essential basis to build thermoelectric generators, which can directly convert heat into electricity. Severe plastic deformation (SPD) via high-pressure torsion (HPT) was successfully applied to enhance ZT of ball-milled and hot-pressed skutterudites as well as to produce bulk nanostructured skutterudites directly from powders. SPD introduces many defects into the sample and in parallel the crystallite size is significantly reduced. During measurement-induced heating these defects anneal partially out, and the grains grow. In this work for the first time systematically the changes of the temperature-dependent electrical resistivity and of thermal expansion were compared. It could be shown that for p- and n-type skutterudites, being hot-pressed and HPT-processed as well as directly HPT-processed from compacted powder, these changes occur more or less simultaneously within the same temperature ranges. This evaluation gives a much deeper insight into the thermoelectric behavior of HPT samples under the influence of changing temperature.     

CaNa[Cr(OH)6] – A Layered Hydroxochromate(III) with Ordered Brucite Structure and its Thermal Decomposition

Green single-crystals of the hydroxochromate(III) CaNa[Cr(OH)₆] were grown under highly alkaline hydrothermal conditions at about 200 °C. The starting materials Ca(NO₃)₂ · 6H₂O and Cr(NO₃)₃ · 9H₂O were reacted in a mixture of water and sodium hydroxide with the molar ratio of 2.8:1. CaNa[Cr(OH)₆] crystallizes in the non-centrosymmetric trigonal space group R3 with the lattice parameters a = 583.86(2) pm and c = 1428.73(6) pm [T = 100(1) K]. Characteristically, the crystals are reverse-obverse as well as inversion twins. The crystal structure is a stack of uncharged metal hydroxide layers, which can be regarded as a cation-ordered rhombohedral variant of the Mg(OH)₂ (brucite) structure type. The oxidation state of chromium(III) and its coordination by hydroxide groups was confirmed by UV/Vis and IR spectroscopy, respectively. Temperature-dependent magnetic measurements revealed paramagnetic behavior with an effective moment of 3.82 μ_B per chromium atom. The thermal decomposition of CaNa[Cr(OH)₆] takes place at about 225 °C, where the fast elimination of 1.5 equivalents of water is followed by the oxidation of chromium(III) to chromium(VI). Upon further heating to 1000 °C and 1200 °C, the intermediate decomposition products CaCrO₄ and Na₂CrO₄ transform into the oxochromates(V) Ca₅(CrO₄)₃O_0.5 and Ca₃(CrO₄)₂, respectively.     

Influence of molecular weight on the thermal decomposition of hydroxyl terminated polybutadiene

Thermogravimetric analysis of hydroxyl terminated polybutadiene (HTPB) and its fractions of different molecular weights separated by preparative GPC shows two major stages of weight loss of different nature in a nitrogen atmosphere. The first stage is primarily depolymerisation, cyclisation and crosslinking of molecules and the second stage is mainly the decomposition of the residue from the first stage. The kinetic parameters, viz. activation energy E and pre-exponential factor A using four different non-isothermal integral equations show a systematic increase with increase in molecular weight for the first stage, whereas for the second stage, the effect of molecular weight on E and A values is not prominent. The increase in E and A values for the first stage is attributed to the formation of greater number of cyclised and crosslinked products from molecules of higher dimensions. Quantitative correlations between the kinetic constants and the molecular weight parameters were derived for the first stage as a quadratic curve following the equation: E or ln A = K₁ − K₂/M (where K₁ and K₂ are empirical constants whose values are different for the different molecular weight averages, viz. M_n, M_w and M_z and for the different equations).     

DSC study of cold and heat denaturation processes of β-lactoglobulin A with guanidine hydrochloride

The cold and heat denaturations of bovine P-lactoglobulin A ((β-lg A) has been studied in solutions of guanidine hydrochloride (GuHCI) by differential scanning calorimetry (DSC). The experimental results are presented and discussed. It is shown that the number of protons bound by the monomeric molecules of β-lg A was unchanged before and after its heat denaturation below pH 3, and that the activation energy of the heat denaturation was depressed owing to the presence of GuHCI. In the solutions with 2.50 and 3.06 mol/L of GuHCI, both the cold and heat denaturations of P-lg A were observed. In comparison with the heat denaturation, the activation energy of cold denaturation was far lower and the number of GuHCl molecules bound by the unfolded polypeptide chains after culd denaturation increased a lot. The absolute value of the enthalpy of cold denaturation was larger than that of heat denaturation. It was found by the analysis that the contribution to the total denaturational enthalpy of conformational change itself of the monomeric molecules of β-lg A was the lowest among the globulins, according to the average of the number of heavy atoms. Project supported by the National Natural Science Foundation of China, and by the fund for excellent items under Director of the Institute of Chemistry.     

Preparation, Structure, and Thermal Decomposition of Co(II) Complexeswith 2,3- and 2,5-Dichlorobenzoic Acid and Imidazole

Summary.  The reaction products of Co(II)-2,3- and -2,5-dichlorobenzoate with imidazole (1, 2; CoL ₂⋯2imdċ2H₂O, L=C₇H₃Cl₂O, imd=imidazole) were characterized by their spectroscopic and thermochemical properties. The compounds crystallize in the monoclonic system with space group = P2₁/c, a=13.848(3), b=12.841(3) ?, c= 7.064(2) ?, β=98.12 °, V=1243.5(4) ?³, Z=2 for 1 and space group =P2₁/n, a=13.293(3), b= 6.964(2), c=13.800(3) ?, β=108.92(3) °, V=1208.6(4) ?³, Z=2 for 2. The complexes lose their crystal water in one step at 333 K and subsequently decompose to CoO with intermediate formation of Co₃O₄. Received August 9, 1999. Accepted (revised) February 11, 2000     

Analysis of DSC Data Relating to Proteins Undergoing Irreversible Thermal Denaturation

New approaches to the analysis of differential scanning calorimetry (DSC) data relating to proteins undergoing irreversible thermal denaturation have been demonstrated. The experimental approaches include obtaining a set of DSC curves at various scanning rates and protein concentrations, and also reheating experiments. The mathematical methods of analysis include construction of a linear anamorphosis and simultaneous fitting of a theoretical expression for the dependence of the excess heat capacity on temperature to a set of experimental DSC curves. Different kinetic models are discussed: the one-step irreversible model, the model including two consecutive irreversible steps, the Lumry and Eyring model with a fast equilibrating first step, and the whole kinetic Lumry and Eyring model. This revised version was published online in July 2006 with corrections to the Cover Date.     

中空TiO_2微球的制备及对聚丙烯酸酯薄膜性能的影响

采用阳离子聚苯乙烯微球作为模板,钛酸四丁酯为钛源,氨水为催化剂,制备了中空TiO_2微球.采用X射线衍射、扫描电镜及比表面测定仪对其形貌和结构进行了表征,并考察了模板粒径、钛源用量以及催化剂用量对中空TiO_2微球形貌的影响.通过物理共混法将其引入至聚丙烯酸酯乳液中并成膜,研究了复合薄膜的保温性能、抗紫外性能及力学性能.结果表明,锐钛矿相中空TiO_2微球模板粒径、钛源用量以及催化剂用量影响中空TiO_2微球的空心尺寸、壁厚及壳层致密性.中空TiO_2微球可显著提升聚丙烯酸酯薄膜的保温性能、抗紫外性能和力学性能.采用不同粒径的模板制备的中空TiO_2微球对复合薄膜的各项性能均有影响,其中模板粒径为140 nm时复合薄膜性能最优,光反射率提升63%,导热系数降低27%,且在波长小于360 nm范围内,紫外透过率几乎为0,抗张强度增加100%,断裂伸长率提升62%.     

Modeling of a counterflow plasma reactor

Modeling of a counterflow plasma reactor is presented, using liquid injection for the synthesis of fine particles. An experimental reactor has been developed in this laboratory, and feasibility has been demonstrated for synthesizing advanced ceramic powders. The flow field calculations show two major recirculating regions which are of importance for increasing the particles' residence time inside of the reactor. In addition, the temperature within these recirculation zones remains relatively uniform. For simulation, water droplet trajectories have been calculated for droplets produced by an injection probe. It is shown that the droplets in a size range below 50 m in diameter will follow the streamlines and evaporate completely within a short traveling distance. This finding suggests that this reactor configuration provides a favorable environment for the synthesis of fine particles using liquid precursors.