Previous studies of the initial stage of oxidation on clean single crystal of Cu(1 0 0) have been extended to the case of the Cu(1 1 0) surface. The dynamic observation of the nucleation and growth of Cu oxide by means of in situ ultra high vacuum transmission electron microscopy (UHV-TEM) shows a highly enhanced oxidation rate on Cu(1 1 0) surface as compared to Cu(1 0 0). The kinetic data on the nucleation and growth of the three-dimensional oxide islands agree well with our heteroepitaxial model of surface diffusion of oxygen. 相似文献
The foam behaviour of low molecular weight polypropylene glycols (PPG) was investigated as a function of concentration and molecular weight (190–2000 g mol−1). For each polypropylene glycol, foam stability increases with concentration and passes through a maximum, beyond which foamability is suppressed as the solubility limit of the glycol is exceeded and droplets of glycol form. Light-scattering data as well as static and dynamic surface tension results provide the key information leading to these interpretations. A maximum in foamability was observed for the PPG molecules with increasing molecular weight (caused by a change in molecular conformation at the interface). This suppresses the Marangoni effect and leads to a decrease in foam stability. 相似文献
The local and the terminal velocities, the size and the degree of bubbles’ shape deformations were determined as a function of distance from the position of the bubble formation (capillary orifice) in solutions of n-octyltrimethylammonium bromide, n-octyldimethylphosphine oxide, n-octyl-β-D-glucopyranoside and n-octanoic acid.
These surface-active compounds have different polar groups but an identical hydrocarbon chain (C8) in the molecule. The motion of the bubbles was monitored and recorded using a stroboscopic illumination, a CCD camera, and a JVC professional video. The recorded bubble images were analyzed by the image analysis software. The bubbles accelerated rapidly and their shape was deformed immediately after detachment from the capillary. The extent of the bubbles’ shape deformation (ratio of horizontal and vertical diameters) was 1.5 in distilled water and dropped rapidly down to a level of ca. 1.05–1.03 with increasing surfactant concentration. After the acceleration period the bubbles either attained a constant value of the terminal velocity (distilled water and high concentrations of the solutions), or a maximum in the velocity profiles was observed (low concentrations). The values of the terminal velocity diminished drastically with increasing concentration, from the value of 35 cm/s in water down to about 15 cm/s, while the bubble diameter decreased by ca. 10% only. The surfactant adsorption at the surface of the bubbles was evaluated and the minimum adsorption coverages required to immobilize the bubbles’ surface were determined. It was found that this minimum adsorption coverage was ca. 4% for n-octyldimethylphosphine oxide, n-octyl-β-D-glucopyranoside, n-octanoic acid and 25% for n-octyltrimethylammonium bromide. The difference in the adsorption coverage together with the surfactants’ surface activities indicate that it is mainly the adsorption kinetics of the surfactants that governs the fluidity of interfaces of the rising bubbles. 相似文献
This paper presents in-time motion adjustment in laser cladding manufacturing process as a means to improve dimensional accuracy and surface finish of the built part. Defects occurring during laser cladding degrade the part quality such as dimensional accuracy and surface finish. In this paper, in-time motion adjustment strategy was presented to remedy and eliminate defects occurring during laser cladding to improve the dimensional accuracy and surface finish. Based on the relationship between the motion of laser head relative to the growing part and other parameters in effects on clad profile, the laser traverse speed, stand-off distance and laser approach orientation to the existing clad layer were adjusted by instructions from a close-loop control system in real time to remedy and eliminate defects. The results of the experiments verified the effects of in-time motion adjustment on dimensional accuracy and surface finish. 相似文献
STM, STS, LEED and XPS data for crystalline θ-Al2O3 and non-crystalline Al2O3 ultra-thin films grown on NiAl(0 0 1) at 1025 K and exposed to water vapour at low pressure (1 × 10−7-1 × 10−5 mbar) and room temperature are reported. Water dissociation is observed at low pressure. This reactivity is assigned to the presence of a high density of coordinatively unsaturated cationic sites at the surface of the oxide film. The hydroxyl/hydroxide groups cannot be directly identify by their XPS binding energy, which is interpreted as resulting from the high BE positions of the oxide anions (O1s signal at 532.5-532.8 eV). However the XPS intensities give evidence of an uptake of oxygen accompanied by an increase of the surface coverage by Al3+ cations, and a decrease of the concentration in metallic Al at the alloy interface. A value of ∼2 for the oxygen to aluminium ions surface concentration ratio indicates the formation of an oxy-hydroxide (AlOxOHy with x + y ∼ 2) hydroxylation product. STM and LEED show the amorphisation and roughening of the oxide film. At P(H2O) = 1 × 10−7 mbar, only the surface of the oxide film is modified, with formation of nodules of ∼2 nm lateral size covering homogeneously the surface. STS shows that essentially the valence band is modified with an increase of the density of states at the band edge. With increasing pressure, hydroxylation is amplified, leading to an increased coverage of the alloy by oxy-hydroxide products and to the formation of larger nodules (∼7 nm) of amorphous oxy-hydroxide. Roughening and loss of the nanostructure indicate a propagation of the reaction that modifies the bulk structure of the oxide film. Amorphisation can be reverted to crystallization by annealing under UHV at 1025 K when the surface of the oxide film has been modified, but not when the bulk structure has been modified. 相似文献
The local adsorption geometry of CO adsorbed in different states on Ni(1 0 0) and on Ni(1 0 0) precovered with atomic hydrogen has been determined by C 1s (and O 1s) scanned-energy mode photoelectron diffraction, using the photoelectron binding energy changes to characterise the different states. The results confirm previous spectroscopic assignments of local atop and bridge sites both with and without coadsorbed hydrogen. The measured Ni–C bondlengths for the Ni(1 0 0)/CO states show an increase of 0.16 ± 0.04 Å in going from atop to bridge sites, while comparison with similar results for Ni(1 1 1)/CO for threefold coordinated adsorption sites show a further lengthening of the bond by 0.05 ± 0.04 Å. These changes in the Ni–CO chemisorption bondlength with bond order (for approximately constant adsorption energy) are consistent with the standard Pauling rules. However, comparison of CO adsorbed in the atop geometry with and without coadsorbed hydrogen shows that the coadsorption increases the Ni–C bondlength by only 0.06 ± 0.04 Å, despite the decrease in adsorption energy of a factor of 2 or more. This result is also reproduced by density functional theory slab calculations. The results of both the experiments and the density functional theory calculations show that CO adsorption onto the Ni(1 0 0)/H surface is accompanied by significant structural modification; the low desorption energy may then be attributed to the energy cost of this restructuring rather than weak local bonding. 相似文献
The surface tension versus temperature data of homologous series of n-alkanes and n-alkenes is analyzed. Critical temperatures are shown to be predicted from these data, with a very high precision, after some
corrections are made. The corrections are shown to arise from the effect of the critical pressure on the extrapolated data
to surface tension approaching zero.
Received: 29 October 1996 Accepted: 13 December 1996 相似文献
We show that, contrary to earlier reports, application of the one-parameter variational technique to the classical (image) model for H in front of an Al surface leads to energy shifts for the ground state which are very close to those obtained numerically with a more sophisticated model of the system. 相似文献
Contaminant uranium poses unique problems for decontamination of former weapons processing and nuclear power facilities, as well as chemical plants, waste storage sites and former mining facilities. In addition, dealing with the possibility of intentional (i.e., a terrorist act) or accidental release of radioactive material in a populated area requires an accurate understanding of the nature of the association of such material with structural surfaces. These surfaces must also be considered in the context of repeated contamination, and the importance of atmospheric exposure, interaction with other possible contaminants, and corrosion or surface degradation due to such exposure must be taken into account. Complementary spectroscopic techniques, especially surface spectroscopies, are essential in developing models for the interaction of contaminants with surfaces and interfaces. In this review (which also presents new data on uranium association with corroding steel surfaces), we collect models of this association as determined by spectroscopic techniques, assess the important considerations in the development of more accurate models, and address some of the questions which remain. 相似文献
Influences of oxygen exposure on the magnetic properties of Co/Ge(1 1 1) ultrathin films have been investigated by surface magneto-optic Kerr effect technique. As the oxygen exposure increases on Co/Ge(1 1 1) films, their magnetic properties could be modified. As an example for 15 ML Co/Ge(1 1 1) films, the coercivity increases from 730 to 920 Oe and the remanence Kerr intensity is reduced for 500 Langmuir (L) of oxygen exposure. Corresponding compositions analyzed by Auger electron spectroscopy measurement shows that the amount of oxygen on the surface layers increases with increasing the oxygen exposure time. Oxygen distributes on the topmost layers of the film. The adsorbed oxygen influences the electronic density of states of Co and results in the changes of the magnetic properties. Besides, the appearance of O/Co/Ge interface could modify the stress anisotropy, and as a result the coercivity of ultrathin Co/Ge(1 1 1) film is enhanced. 相似文献