聚氯乙烯—丁腈橡胶—氯丁橡胶三元共混物的研究

测定了聚氯乙烯（ＰＶＣ）－丁脯橡胶（ＮＢＲ－２９）－氯丁橡胶（ＣＲ）三元共混物的冲击性能和应力－应变行为，用动态力分析、扫描电和透射电镜研究了共混物的相容性和形态结构。结果表明，ＮＢＲ－２９对ＰＶＣ，ＣＲ有良好的增容作用，三元共混物是部分相容的二相体系，具有良好的抗冲击性能。     

Loss and recovery in hydrophobicity of silicone rubber exposed to corona discharge

This paper describes the loss and recovery in the hydrophobicity of unfilled high temperature vulcanized silicone rubber (HTV-SR) resulting from corona discharge. In this study, HTV-SR specimens were exposed to corona stress generated by a parallel needle-plane electrode system, and physicochemical analyses on the surface layer of SR before and after corona discharge treatment were carried out by using Fourier transform infra-red (FTIR) spectroscopy, scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). It is demonstrated that hydrophilic OH groups that are by-products of ageing can be formed instead of hydrophobic CH₃ groups on the surface of aged SR and the corona discharge plays an important role on the temporary loss of hydrophobicity. After a substantial period of ‘rest’, the hydrophobic recovery of SR results from the diffusion of low-molecular weight (LMW) silicone fluid from the bulk onto the aged layer.     

高抗冲聚苯乙烯的增韧机理

概述了以高抗冲聚苯乙烯（ＨＩＰＳ）为中心的有关橡胶增韧机理的理论，并且总结了界面，性能、粒子尺寸、粒 距及缠结密度等因素对橡胶／高分子共混体系性能的影响。     

Dependence of mechanical and aging properties of chloroprene rubber on silica and ethylene thiourea loadings

The interaction between precipitated silica and chloroprene rubber (CR) was investigated using a nuclear magnetic resonance (NMR) technique. The results reveal that the silanol groups on silica surface could chemically react with CR. Crosslinking of CR is therefore possible in the presence of silica at high temperature. The effects of silica and ethylene thiourea (ETU) loadings on properties of the silica-filled CR were thereafter investigated. With increasing silica loading, the compound viscosity increases considerably due to the dilution effect. As silica could act as a curative for CR, increasing silica loading results in both faster cure rate and increased crosslink density. The optimum tensile strength is found at approximately 30 phr of silica loading. The results also show that silica loading has little effect on most aging properties, except the relative modulus in which it increases rapidly with increasing silica loading due to the post curing effect. Similar to the effect of silica loading, the compound viscosity, cure rate and crosslink density are all increased with increasing ETU loading. The tensile strength is, on the other hand, slightly affected by ETU loading. Exception is found at high loading where the tensile strength drops noticeably. Interestingly, aging resistance of the vulcanizate is found to improve with the addition of ETU. Explanation is given by the hindrance capability of ETU to post curing.     

Morphology of peroxide-prevulcanised natural rubber latex: effect of reaction time and deproteinisation

A non-uniform mesh structure, i.e. a dense network near the surface of peroxide-prevulcanised natural rubber latex particles, was observed under transmission electron microscopy. In the initial period of prevulcanisation, the swelling ratio of the latex sheet decreased with longer reaction time while an increase in crosslink density of rubber particles containing polystyrene, prepared using the phase transfer/bulk polymerisation process, was noticed. The modulus of the rubber sheet increased up to maximum crosslinking and thereafter decreased. After removal of proteins from the latex membrane layer, derived from protein-lipid originally existing at the rubber particle surface, could not be detected. The absence of proteins, which act as free radical scavengers, resulted in a rapid diffusion of alkoxy radicals into the rubber phase of deproteinised latex and, therefore, a uniform crosslink distribution inside each particle was obtained.     

Morphology, crystallization behavior and properties of impact-modified polypropylene copolymer with or without sodium benzoate as a nucleating agent

 The morphology, crystallization behavior, and properties of an impact-modified polypropylene (PP) copolymer with or without sodium benzoate were investigated. The contents of ethylene–propylene rubber (EPR) in the reactor-made PP copolymer is about 15 wt%. For comparison, blends of PP and EPR containing the same EPR composition were prepared by melt-mixing. Morphological studies by scanning probe microscopy indicated that the impact-modified copolymer consists of three different phases, i.e., polyethylene, PP, and EPR phases, which is considerably different from the morphology of the conventional PP/EPR blend of the corresponding composition. The impact-modified PP copolymer exhibited a higher crystallization rate in terms of the lower crystallization half-time and thus higher thermal and mechanical properties, such as impact strength and hardness, than the PP/EPR blend did. The addition of sodium benzoate as a nucleating agent to the copolymer increased the crystallization rate and the mechanical properties. Received: 4 June 2001 Accepted: 31 October 2001     

醋酸乙烯酯在硅橡胶上的辐射接枝研究

研究了不同溶剂中的醋酸乙烯酯在硅橡胶上的辐射接技状况及接枝后硅橡胶表面结构情况．结果表明：（１）在硅橡胶－乙酸乙酯－醋酸乙烯酯体系中，接枝有自加速效应；（２）适量加入对苯二酚，接枝诱导期延长，接枝速率下降，凝胶效应消失，辐射接技经验关联式为ＲＰ＝０．２７×［Ｄ］（－０．５６０）×［Ｉ］（０．４９０）×［Ｃ］（０．９２０），接核反应为扩散控制反应；（３）不同的溶剂对硅橡胶接枝有不同的影响，如甲醇发生敏化作用，提高接枝速率，而苯发生惰化作用，降低接枝速率；（４）在合适的甲醇和苯配比时，接枝反应几乎恒速进行，用扫描电镜（ＳＥＭ）观察断面，接枝区比较均一，出现微相分离．     

The preparation of thick-film glass capillary columns

A detailed method for the routine preparation of glass capillary columns is presented. The method consists of coating a glass tube with quartz powder prior to pulling the tube into a capillary. The inner surface of the capillary consists of an even distribution of quartz particles fused to the walls. This surface has been found readily deactivated by standard procedures and ideal for the preparation of thick-film glass capillary columns. The method has been thoroughly tested in two independent laboratories to ensure that the procedures described are reproducible.     

Surface modified precipitated calcium carbonates at a high degree of dispersion

Calcium carbonates of different degrees of surface hydrophobicity were obtained when sorbic acid or polyoxyethylene glycol were present during the precipitation. In the presence of trace amounts of divalent cations carbonates with high surface hydrophilicity and improved monodisperse character are obtained. Surface modification of the calcium carbonates by several proadhesive compounds can markedly improve the chemical affinity of the carbonates to polymers. Very effective are isostearoyl titanate and two polyoxyethylene compounds. Precipitated calcium carbonates modified with 2 to 3 percent (wt/wt) of isostearoyl titanate increased the tensile strenght of butadiene-styrene rubber by approximately 100%. Polyurethane is only strengthened when 30 wt/wt of a filler are introduced independently of the type proadhesive compounds. The best strength and hysteresis of polyurethanes are obtained with calcium carbonate modified with 2 percent (wt/wt) of polyoxyethylene glycol.     

交联助剂对PPC／NBR弹性体结构和性能的影响

研究了马来酸酐（ＭＡ）及异氰脲酸三烯丙酯（ＴＡＩＣ）对聚丙撑碳酸酯／丁腈橡胶共混弹性体结构和性能的影响，发出加入ＭＡ或ＴＡＩＣ能有效地改善交联网络；加入适量ＭＡ能显著改善共混弹性体热氧老化稳定性；加入ＴＡＩＣ使共混弹性体具有优良的高弹特性和力学性能。