毛细管电泳柱端酶微反应器研究进展

微反应器是指使物理、化学、生化等反应在微小的空间内发生的装置。微反应器能减少试剂消耗和样品污染,且反应条件易于控制,特别适合于酶促反应分析,因而多为酶微反应器。微反应器与电泳联用时,可将毛细管柱端作为微反应器,集反应与分离于一根毛细管柱上,可实现反应与分离一次性完成。根据酶微反应器制备原理的不同进行分类,综述了近2年来毛细管电泳柱端酶微反应器的研究进展。     

电泳中介微分析法测定超氧化物歧化酶

基于超氧化物歧化酶(SOD)对邻苯三酚自氧化的抑制作用和电泳中介微分析(EMMA)技术建立了一种测定SOD的新方法。采用“三明治”式不同pH缓冲液部分填充法,有利于邻苯三酚的自氧化反应,便于观察SOD的抑制作用,有利于反应产物与反应物的分离。对溶液填充模式、反应条件等实验参数进行了优化。在最优条件下,邻苯三酚自氧化反应的抑制率I与SOD浓度C在1.00×102~6.00×102μg/L范围内呈良好的线性关系,回归方程为:I(%)=0.0895C(μg/L) 17.633(r=0.9973)。     

Spectrochemical analysis of powder using 355 nm Nd-YAG laser-induced low-pressure plasma

The applicability of spectrochemical analysis of minute amounts of powder samples was investigated using an ultraviolet Nd-YAG laser (355 nm) and low-pressure ambient air. A large variety of chemical powder samples of different composition were employed in the experiment. These included a mixture of copper(II) sulfate pentahydrate, zinc sulfide, and chromium(III) sulfate n-hydrate powders, baby powder, cosmetic powders, gold films, zinc supplement tablet, and muds and soils from different areas. The powder samples were prepared by pulverizing the original samples to an average size of around 30 μm in order to trap them in the tiny micro holes created on the surface of the quartz subtarget. It was demonstrated that in all cases studied, good quality spectra were obtained with low background, free from undesirable contamination by the subtarget elements and featuring ppm sensitivity. A further measurement revealed a linear calibration curve with zero intercept. These results clearly show the potential application of this technique for practical qualitative and quantitative spectrochemical analysis of powder samples in various fields of study and investigation.     

Electron probe microanalysis of SiO2-coated minerals: Subsurface phases in quartz

Crystal fragments of biotite, garnet, and spinel were mounted together in one block which afterwards was sawn into several pieces; each piece was coated with SiO₂ of varying thickness, up to 7.9m. Electron probe microanalysis was carried out at various accelerating voltages of the major elements present, using the non-SiO₂-coated minerals as reference standard.Calibration curves, depth below the surface versus ratios of X-ray yields, have been established with the ultimate goal to use them for a (semi)-quantification of elements present in subsurface phases in quartz, a common host mineral in rocks.     

Combined EPMA and AES depth profiling of a multilayer Ti-Al-O-N coating

In order to compare thin-film electron probe microanalysis (EPMA) and Auger electron spectroscopy (AES) regarding reliability in quantifying chemical compositions of Ti-Al-O-N coatings with depth, a multilayer was prepared on a silicon wafer by using reactive ionized cluster beam deposition technique. Within a total thickness of about 25 nm the composition of the multilayer varied step by step from Ti-Al-O-N at the bottom to Al-O at the top. AES and, as an innovation, EPMA crater edge profiling was applied to measure the composition with depth. For quantification special thin-film EPMA techniques based on Monte Carlo simulations were applied. The chemical binding states of Al and Ti with depth were analysed using a high resolution energy analyser (MAC 3) for the AES investigations working in the direct mode. According to the deposition procedure the concentration profiles of the components varied with depth for both AES and EPMA measurements. AES provided a better depth resolution than EPMA. To get a true calibration of the depth scale an in-situ measurement method like an optical interferometry will be required. Assuming that the relative sensitivity factors are available AES depth profiling delivers concentration profiles with good accuracy. The new EPMA application provided quantitative depth profiles concerning concentration and coverage. For EPMA crater edge profiling the coating needs to be deposited on a foreign substrate because depth distributions of elements being present in both the layer and the substrate cannot be resolved.The combination of AES-depth profiling with EPMA crater edge profiling techniques is a powerful tool to analyse heterostructures quantitatively.     

Analytical,structural and electrical characterization of SiGe layers by electron microbeam techniques

k-ratios of Ge-L and Si-K measured at different beam energies allow to evaluate simultaneously composition and thickness of SiGe layers on a Si substrate. A simple technique applying backscattered electrons also enables estimation of composition of bulk SiGe and of composition and thickness of relatively thick (200 nm) SiGe layers on Si. Electron channeling patterns of pseudomorphic SiGe/Si structures and of pure Si substrate show no significant differences whereas in relaxed structures a smearing of the pattern with increasing density of misfit dislocations is observed. Under particular conditions the technique of the electron beam induced current permits imaging of recombination-active misfit dislocations with a spatial resolution around 0.2 m. Moreover, a repulsion of holes due to the valence-band offset in a n-Si/SiGe heterostructure was detected.     

新材料的发展与分析化学

文章介绍了新材料的重要性及发展方向,分析化学在新材料研制中起着耳目的作用,另一方面新材料也为分析化学的进展提供了课题与条件。微量分析、微区分析、表面分析是此领域中的重点。在未来的发展中,分析化学在材料的发展中的地位不会改变,并期待着分析灵敏度与空间分辩率的进一步提高。     

Screening of aromatase inhibitors in traditional Chinese medicines by electrophoretically mediated microanalysis in a partially filled capillary

An electrophoretically mediated microanalysis method with partial filling technique was developed for screening aromatase inhibitors in traditional Chinese medicine. The in‐capillary enzymatic reaction was performed in 20 mM sodium phosphate buffer (pH 7.4), and sodium phosphate buffer (20 mM, pH 8.0) was used as a background electrolyte. A long plug of coenzyme reduced β‐nicotinamide adenine dinucleotide 2′‐phosphate hydrate dissolved in the reaction buffer was hydrodynamically injected into a fused silica capillary followed by the injection of reaction buffer, enzyme, and substrate solution. The reaction was initiated with a voltage of 5 kV applied to the capillary for 40 s. The voltage was turned off for 20 min to increase the product amount and again turned on at a constant voltage of 20 kV to separate all the components. Direct detection was performed at 260 nm. The enzyme activity was directly assayed by measuring the peak area of the produced β‐nicotinamide adenine dinucleotide phosphate and the decreased peak area indicated the aromatase inhibition. Using the Lineweaver–Burk equation, the Michaelis–Menten constant was calculated to be 50 ± 4.5 nM. The method was applied to the screening of aromatase inhibitors from 15 natural products. Seven compounds were found to have potent AR inhibitory activity.     

A New Method to Examine Interfacial Reactions of a Multilayered System NiAl–Hf–hBN on a Sapphire Fibre

Fibre reinforced NiAl offers new possibilities for the development of high strength structural materials of low density applicable in gas turbines at high operating temperatures. The properties of composite materials are strongly influenced by the strength of the fibre–matrix interface. In addition, if fibre and matrix differ in their thermal expansion coefficients, a well controlled interface reaction at high temperature changes is demanded. Therefore, two layers consisting of BN and Hf were embedded between a sapphire fibre and NiAl and heated at 1350 °C to find a compromise between adhesion and ductility. The control and characterization of the reaction zone is essential for the development of these new materials. Especially, the characterization of the fibre-coating interface is a challenge. The different hardness of fibre and coating makes it nearly impossible to use a conventional cross-section preparation. Further, the small dimension of the reaction zone requires the use of analytical techniques providing high lateral resolution. In order to accomplish these requirements, a newly developed technique FIB (Focused Ion Beam)-EPMA (Electron Probe Microanalysis) was combined with XRD (X-ray diffraction). XRD was performed for the identification of the phases. The reaction zone was exposed by a special FIB preparation technique and examined by surface-sensitive EPMA. This allowed to determine the spatial distribution of the different phases.     

Characterization of SiC-platelets

Three fractions of SiC platelets were characterized using polarizing microscopy, X-ray diffraction, high resolution Auger electron spectroscopy (AES), electron spectroscopy for chemical analysis (ESCA) and scanning electron microscopy with energy dispersive analysis (SEM/EDX). The chemical analysis of the three fractions is given. The determination of the SiC polytypes (4H, 6H, 15R, 3C) was done and has been correlated with the chemical analysis. The results of the X-ray diffraction investigations confirm the polarizing microscopy observations. Using microanalytical techniques important conclusions about the impurity elements (e.g. B, Al, Fe) and their local distribution could be drawn. Most of them were found to be present on the outermost surfaces of the platelets. Some conclusions concerning the processing of the platelets are suggested.Dedicated to Professor Günther Tölg on the occasion of his 60th birthday