Scheduling orders for multiple product types to minimize total weighted completion time

We consider the problem of scheduling orders for multiple different product types in an environment with m dedicated machines in parallel. The objective is to minimize the total weighted completion time. Each product type is produced by one and only one of the m dedicated machines; that is, each machine is dedicated to a specific product type. Each order has a weight and may also have a release date. Each order asks for certain amounts of various different product types. The different products for an order can be produced concurrently. Preemptions are not allowed. Even when all orders are available at time 0, the problem has been shown to be strongly NP-hard for any fixed number (?2) of machines. This paper focuses on the design and analysis of efficient heuristics for the case without release dates. Occasionally, however, we extend our results to the case with release dates. The heuristics considered include some that have already been proposed in the literature as well as several new ones. They include various static and dynamic priority rules as well as two more sophisticated LP-based algorithms. We analyze the performance bounds of the priority rules and of the algorithms and present also an in-depth comparative analysis of the various rules and algorithms. The conclusions from this empirical analysis provide insights into the trade-offs with regard to solution quality, speed, and memory space.     

Study on the Baryon State X Produced in the Process J／ψ→p＋X,X→p＋P

The decay process J/ψ→p X X→p P，where p,p and P are the proton,antiproton and pseudoscalar states,respectively,has been studied in terms of the angular distribution and the generalized moment analysis methods.The result shows that we can identify the spin,but cannot determine the parity of the baryon resonance state X produced in the process J/ψ→p X X→p P.     

Mode beating in spot-size converter lasers

An anomalous modulation in the wavelength spectrum has been observed in lasers with spot-size converters. This intensity modulation is shown to be caused by beating between the fundamental lasing mode and radiation modes in the taper. This results in a periodic modulation in the net gain spectrum, which causes wavelength jumps between adjacent net gain maxima, and a drive current dependent spectral width that is expected to affect system performance. The amplitude of this spectral modulation is reduced significantly by either using an angled rear-facet which reflects the beating radiation modes away from the laser axis, or by using a nonlinear, adiabatic taper.     

分置式斯特林制冷机失效分析

斯特林制冷机是红外探测器组件中一个关键的组成部分。目前我国斯特林制冷机的性能指标与国外同类产品差距缩短 ,但可靠性问题一直没有很好解决。文中介绍了斯特林制冷机的原理、双活塞对动型分置式斯特林制冷机的结构特点及表征参数 ;通过对产品研制开发过程中成品率低的原因分析 ,揭示了主要失效机理 ,对改进工艺和设计起到了参考和指导作用。     

狭缝式高速摄影机胶片的计算机判读

根据狭缝摄影机胶片的成象原理,运用数字图象处理技术,对狭缝式高速摄影机胶片判读工作的计算机化进行研究.应用结果表明,该技术先进实用,极大地提高了判读的精度和效率,将是这种胶片判读技术的发展方向.     

Experimental identification of physical parameters of fluid-filled pipes using acoustical signal processing

A method is formulated for the identification of an unknown physical parameter of a fluid-filled pipe using the measurement of sound speed in the pipe. The method uses a simple formula which provides the relationship between the sound speed and a few physical parameters of the pipe: thickness, diameter, wall material constants and fluid constants. Once the sound speed in the pipe is measured, the simple formula can be used to extract one of the unknown parameters providing the remaining ones are known.The sound speed in the pipe is measured using a 3-transducer array. In order to demonstrate the potential of the technique the results of several measurements obtained in a water-filled steel pipe are presented.The required accuracy of the measurement of sound speed and of the specification of known parameters is analysed. The accuracy depends on the unknown parameter which is to be identified. For example, if the pipe thickness is the unknown parameter, the other parameters have to be known within a very narrow margin of error. On the contrary, if the fluid properties have to be identified the needed accuracy of known parameters gets much lower.     

Synthesis and structures of nitroxyalkyl methylphosphonates

The reactions of ethylene glycol mononitrate and glycerol 1,3-dinitrate with methylphosphonic dichloride afforded new nitroxyalkyl methylphosphonates.     

中学生男性性别角色期望的因子模型与应用

运用中学生男性性别角色期望调查表和因子分析方法对贵阳市中学生进行男性性别角色期望调查和定性与定量分析,为中学生树立适宜的性别角色观,促进其心理健康发展提供量化依据.分析显示:传统的男性角色并不被现代中学生完全接受,无论是男中学生还是女中学生都在力图探求一种新的男性性别角色模式,且两性中学生对这一新的男性性别角色模式的期望和把握是有一定差异的.     

Numerical analysis of the Toda lattice equations

Numerical solutions to three systems of integrable evolutionary equations from the Toda lattice hierarchy are analyzed. These are the classical Toda lattice, the second local dispersive flow, and the second extended dispersive flow. Special attention is given to the properties of soliton solutions. For the equations of the second local flow, two types of solitons interacting in a special manner are found. Solutions corresponding to various initial data are qualitatively outlined.     

Thermal treatment on composite γ-zirconium phosphate-silica

The prepared amorphous γ-ZrP\SiO₂ composite had a complicated composition, since a part of γ-ZrP is converted to α-form during the exfoliation of it. The γ-ZrP\SiO₂ composite have specific surface area of 421 m²g^–1. The acidic P–OH groups of the lamellae species placed on the surface (it is ≈1.0 meq g^–1), do not destroy until the temperature of 1030 K. During the thermal treatment the total mass loss of 7.79% was found. This value corresponds to 0.42 mole of H₂O per molecule unit. The water loss process was found very slow, because of the placing of bilamellar species in the composite.